The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these

The centre to centre spacing of vertical stirrups, in a rectangular beam, is
(a) Increased towards the centre of the span of the beam
(b) Decreased towards the centre of the span of the beam.
(c) Increased at the ends.
(d) None of these
by

1 Answer

Answer :

(a) Increased towards the centre of the span of the beam
by

Related questions

Spacing of stirrups in a rectangular beam, is (A) Kept constant throughout the length (B) Decreased towards the centre of the beam (C) Increased at the ends (D) Increased at the centre of the beam

Description : Spacing of stirrups in a rectangular beam, is (A) Kept constant throughout the length (B) Decreased towards the centre of the beam (C) Increased at the ends (D) Increased at the centre of the beam

Last Answer : Answer: Option D

In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Description : In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Last Answer : [ B ] May be increased

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Last Answer : Answer: Option C

If a beam fails in bond, then its bond strength can be increased most economically by (A) Increasing the depth of beam (B) Using thinner bars but more in number (C) Using thicker bars but less in number (D) Providing vertical stirrups

Description : If a beam fails in bond, then its bond strength can be increased most economically by (A) Increasing the depth of beam (B) Using thinner bars but more in number (C) Using thicker bars but less in number (D) Providing vertical stirrups

Last Answer : Answer: Option B

Maximum allowable spacing of shear reinforcement for vertical stirrups is restricted to [ A ] d [ B ] 0.45 d [ C ] 0.75 d [ D ] 0.90 d

Description : Maximum allowable spacing of shear reinforcement for vertical stirrups is restricted to [ A ] d [ B ] 0.45 d [ C ] 0.75 d [ D ] 0.90 d

Last Answer : [ C ] 0.75 d

According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Last Answer : [ C ] lesser of 0.75 d or 300 mm

What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Last Answer : (a) Zero

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is (A) Safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Last Answer : Answer: Option A

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is increased by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Last Answer : Answer: Option C

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.

Description : The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.

Last Answer : (d) Increases with increase in stirrups and longitudinal steels.

According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Description : According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Last Answer : (a) Equal to

Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Description : Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Last Answer : [ D ] d

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (B) L/3 

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Description : A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Last Answer : Answer: Option A

The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Description : The maximum deflection of a simply supported beam of span L, carrying an isolated load at the  centre of the span; flexural rigidity being EI, is  (A) WL3 /3EL (B) WL3 /8EL (C) WL3 /24EL (D) WL3 /48EL

Last Answer : (D) WL3 /48EL

Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at support. 4. Increases the positive moment at the centre of span. Of these statements (A) 1 and 4 are correct (B) 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Description : Consider the following statements: Sinking of an intermediate support of a continuous beam 1. Reduces the negative moment at support. 2. Increases the negative moment at support. 3. Reduces the positive moment at ... 1 and 3 are correct (C) 2 and 3 are correct (D) 2 and 4 are correct

Last Answer : (A) 1 and 4 are correct

A simply supported beam carrying a uniformly distributed load over its whole span, is propped at the centre of the span so that the beam is held to the level of the end supports. The reaction of the prop will be (A) Half the distributed load (B) 3/8th the distributed load (C) 5/8th the distributed load (D) Distributed load

Description : A simply supported beam carrying a uniformly distributed load over its whole span, is propped at  the centre of the span so that the beam is held to the level of the end supports. The reaction of  ... B) 3/8th the distributed load  (C) 5/8th the distributed load  (D) Distributed load 

Last Answer : (C) 5/8th the distributed load 

Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Description : Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Last Answer : Answer: Option C

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

A simply supported beam AB is subjected to a concentrated load at C, the centre of the span. The area of the SF diagram from A to C will give a) BM at C b) Load at S c) SF at C d)Difference between BM values at A and C

Description : A simply supported beam AB is subjected to a concentrated load at C, the centre of the span. The area of the SF diagram from A to C will give a) BM at C b) Load at S c) SF at C d)Difference between BM values at A and C

Last Answer : d)Difference between BM values at A and C

The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Description : The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Last Answer : (d) Least of (a) , (b) or (c)

The depth of the centre of pressure on a vertical rectangular gate 8 m wide and 6 m high, when the water surface coincides with the top of the gate, is (A) 2.4 m (B) 3.0 m (C) 4.0 m (D) 5.0 m

Description : The depth of the centre of pressure on a vertical rectangular gate 8 m wide and 6 m high, when the water surface coincides with the top of the gate, is (A) 2.4 m (B) 3.0 m (C) 4.0 m (D) 5.0 m

Last Answer : Answer: Option B

For a beam having fixed ends, the unknown element of the reactions, is (A) Horizontal components at either end (B) Vertical components at either end (C) Horizontal component at one end and vertical component at the other (D) Horizontal and vertical components at both the ends

Description : For a beam having fixed ends, the unknown element of the reactions, is  (A) Horizontal components at either end  (B) Vertical components at either end  (C) Horizontal component at one end and vertical component at the other  (D) Horizontal and vertical components at both the ends 

Last Answer : (D) Horizontal and vertical components at both the ends 

A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2

Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of  moment M at its centre. The maximum bending moment in the beam is  (A) M (B) M/2  (C) M/3  (D) ML/2 

Last Answer : (A) M

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

The function of king post in a king post roof truss is (A) To support the frame work of the roof (B) To receive the ends of principal rafter (C) To prevent the walls from spreading outward (D) To prevent the tie beam from sagging at its centre

Description : The function of king post in a king post roof truss is (A) To support the frame work of the roof (B) To receive the ends of principal rafter (C) To prevent the walls from spreading outward (D) To prevent the tie beam from sagging at its centre

Last Answer : Answer: Option D

In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Description : In a perfect prismatic compass (A) Magnetic axis and geometric axis of the needle coincide (B) Ends of the needle and pivot are in same vertical and horizontal planes (C) Pivot is vertically over the centre of the graduated circle (D) All the above

Last Answer : (D) All the above

Tower diameter may be decreased by (A) Using higher reflux ratio (B) Use of increased tray spacing (C) Increasing the liquid flow rate (D) Increasing the vapour flow rate

Description : Tower diameter may be decreased by (A) Using higher reflux ratio (B) Use of increased tray spacing (C) Increasing the liquid flow rate (D) Increasing the vapour flow rate

Last Answer : (B) Use of increased tray spacing

To ensure uniform pressure distribution, the thickness of the foundation, isA) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Description : To ensure uniform pressure distribution, the thickness of the foundation, is A) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Last Answer : Answer: Option C

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

Maximum deflection in a S.S beam with UDL w over the entire span will be a. at the left hand support. b.at the right support. c. at the centre. d.none.

Description : Maximum deflection in a S.S beam with UDL w over the entire span will be a. at the left hand support. b.at the right support. c. at the centre. d.none.

Last Answer : c. at the centre.

The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Last Answer : (d) Zero

For a simply supported beam of span L, with point load W at the centre, the maximum B.M. will be (a) WL (b) WL/2 (c) WL/4 (d) WL/8

Description : For a simply supported beam of span L, with point load W at the centre, the maximum B.M. will be (a) WL (b) WL/2 (c) WL/4 (d) WL/8

Last Answer : (c) WL/4

A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Description : A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.

Last Answer : c.17.45 mm

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx