To ensure uniform pressure distribution, the thickness of the foundation, isA) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

To ensure uniform pressure distribution, the thickness of the foundation, is
A) Kept uniform throughout
(B) Increased gradually towards the edge
(C) Decreased gradually towards the edge
(D) Kept zero at the edge
by

1 Answer

Answer :

Answer: Option C
by

Related questions

Spacing of stirrups in a rectangular beam, is (A) Kept constant throughout the length (B) Decreased towards the centre of the beam (C) Increased at the ends (D) Increased at the centre of the beam

Description : Spacing of stirrups in a rectangular beam, is (A) Kept constant throughout the length (B) Decreased towards the centre of the beam (C) Increased at the ends (D) Increased at the centre of the beam

Last Answer : Answer: Option D

A wedge shaped thin has (a) Non-uniform thickness (b) Zero thickness at one end and it increasing towards other end (c) Zero thickness at both ends (d) Thickness increase and decrease alternately

Description : A wedge shaped thin has (a) Non-uniform thickness (b) Zero thickness at one end and it increasing towards other end (c) Zero thickness at both ends (d) Thickness increase and decrease alternately

Last Answer : b) Zero thickness at one end and it increasing towards other end

A wedge shaped thin has A. Non-uniform thickness B. Zero thickness at one end and it increasing towards other end C. Zero thickness at both ends D. Thickness increase and decrease alternately

Description : A wedge shaped thin has A. Non-uniform thickness B. Zero thickness at one end and it increasing towards other end C. Zero thickness at both ends D. Thickness increase and decrease alternately

Last Answer : B. Zero thickness at one end and it increasing towards other end

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

On an absolutely rigid foundation base, the pressure will (A) Be more at the edges of the foundation (B) Be uniform (C) Not be uniform (D) Be zero at the centre of the foundation

Description : On an absolutely rigid foundation base, the pressure will (A) Be more at the edges of the foundation (B) Be uniform (C) Not be uniform (D) Be zero at the centre of the foundation

Last Answer : Answer: Option C

Hardening of cement occurs at (A) Rapid rate during the first few days and afterwards it continues to increase at a decreased rate (B) Slow rate during the first few days and afterwards it continues to increase at a rapid rate (C) Uniform rate throughout its age (D) None of these

Description : Hardening of cement occurs at (A) Rapid rate during the first few days and afterwards it continues to increase at a decreased rate (B) Slow rate during the first few days and afterwards it continues to increase at a rapid rate (C) Uniform rate throughout its age (D) None of these

Last Answer : Answer: Option D

The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete is (a) Uniform compression throughout (b) Zero at one end and compression at the other end (c) Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Last Answer : (b) Zero at one end and compression at the other end

direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure developed during the test (C) As the test progresses the area under shear, gradually changes (D) None of these

Description : direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure ... C) As the test progresses the area under shear, gradually changes (D) None of these

Last Answer : Answer: Option C

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is increased by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Last Answer : Answer: Option C

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Description : In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Last Answer : [ B ] May be increased

The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these

Description : The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these

Last Answer : (a) Increased towards the centre of the span of the beam

Which of the following is the optimum operating condition for an exothermic reversible reaction taking place in a plug-flow reactor? (A) Temperature should be high in the beginning and decreased towards the end of the reaction (B) Very low temperature should be used throughout the reaction (C) Very high temperature should be used throughout the reaction (D) None of these

Description : Which of the following is the optimum operating condition for an exothermic reversible reaction taking place in a plug-flow reactor? (A) Temperature should be high in the beginning and decreased towards ... reaction (C) Very high temperature should be used throughout the reaction (D) None of these

Last Answer : (A) Temperature should be high in the beginning and decreased towards the end of the reaction

A square coil of edge I having n turns carries a curent i. it is kept on a smooth horizontal plate. A uniform magnetic field B exists in a direction p

Description : A square coil of edge I having n turns carries a curent i. it is kept on a smooth horizontal plate. A uniform magnetic field B exists in a direction p

Last Answer : A square coil of edge I having n turns carries a curent i. it is kept on a smooth horizontal plate. A uniform ... . `(Mg)/(4niL)` D. `(2Mg)/(niL)`

In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Description : In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Last Answer : (B) Increase gradually

When the flow in an open channel is gradually varied, the flow is said to be (A) Steady uniform flow (B) Steady non-uniform flow (C) Unsteady uniform flow (D) Unsteady non-uniform flow

Description : When the flow in an open channel is gradually varied, the flow is said to be (A) Steady uniform flow (B) Steady non-uniform flow (C) Unsteady uniform flow (D) Unsteady non-uniform flow

Last Answer : Answer: Option B

Gradually varied flow is (A) Steady uniform (B) Non-steady non-uniform (C) Non-steady uniform (D) Steady non-uniform

Description : Gradually varied flow is (A) Steady uniform (B) Non-steady non-uniform (C) Non-steady uniform (D) Steady non-uniform

Last Answer : Answer: Option D

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Last Answer : (C) Varies exponentially, being more near the torque-input end

A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its outside edge is: w) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Description : A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its ... ) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Last Answer : ANSWER: Z -- CIRCLES THE AXIS OF THE ROD

In wedge shaped film the interference pattern has nature (a) Parallel to the end where thickness is non-zero (b) Perpendicular to contact edge (c) Parallel to contact edge (d) Perpendicular to the end where thickness is non-zero

Description : In wedge shaped film the interference pattern has nature (a) Parallel to the end where thickness is non-zero (b) Perpendicular to contact edge (c) Parallel to contact edge (d) Perpendicular to the end where thickness is non-zero

Last Answer : (c) Parallel to contact edge

During drying of a solid, the critical moisture content increases with (A) Decreased drying rate (B) Increased thickness of the solid (C) Increased drying rate (D) Both (B) and (C)

Description : During drying of a solid, the critical moisture content increases with (A) Decreased drying rate (B) Increased thickness of the solid (C) Increased drying rate (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

In reference with antireflection coating which of the following statement is true? A. Thickness of the film should be changed for light of same wavelength but different intensity B. Thickness of the film need not be changed for light of same wavelength but different intensity C. Thickness of the film should be increased for light of same wavelength but higher intensity D. Thickness of the film should be decreased for light of same wavelength but higher intensity

Description : In reference with antireflection coating which of the following statement is true? A. Thickness of the film should be changed for light of same wavelength but different intensity B. Thickness of ... D. Thickness of the film should be decreased for light of same wavelength but higher intensity

Last Answer : B. Thickness of the film need not be changed for light of same wavelength but different intensity

For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (B) Is decreased

For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (C) Remains unchanged

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

Contact pressure beneath a rigid footing resting on cohesive soil is (A) Less at edges compared to middle (B) More at edges compared to middle (C) Uniform throughout (D) None of the above

Description : Contact pressure beneath a rigid footing resting on cohesive soil is (A) Less at edges compared to middle (B) More at edges compared to middle (C) Uniform throughout (D) None of the above

Last Answer : Answer: Option B

Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Description : Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Last Answer : Hoop shrinking technique is used to make the stresses on the cylinder walls evenly distributed around the circumference of the cylinder, which results in a uniform stress distribution. This is important for ... under load. It also makes sure that the cylinder can withstand the pressure inside it.

The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Description : The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Last Answer : (c) Uniform stresses

The range of spread from the wall base to outer edge of a brick work foundation does not exceed (A) 1/2 horizontal to 1 vertical (B) 2/3 horizontal to 1 vertical (C) 1 horizontal to 1 vertical (D) 2 horizontals to 1 vertical

Description : The range of spread from the wall base to outer edge of a brick work foundation does not exceed (A) 1/2 horizontal to 1 vertical (B) 2/3 horizontal to 1 vertical (C) 1 horizontal to 1 vertical (D) 2 horizontals to 1 vertical

Last Answer : Answer: Option C

For absorbing a sparingly soluble gas in a liquid (A) Gas side mass transfer co-efficient should be increased (B) Liquid side mass transfer co-efficient should be increased (C) Liquid side mass transfer co-efficient should be decreased (D) Mass transfer co-efficient must be kept constant

Description : For absorbing a sparingly soluble gas in a liquid (A) Gas side mass transfer co-efficient should be increased (B) Liquid side mass transfer co-efficient should be increased (C) Liquid side mass transfer co-efficient should be decreased (D) Mass transfer co-efficient must be kept constant

Last Answer : (B) Liquid side mass transfer co-efficient should be increased

In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Last Answer : Answer: Option B

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Description : When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Last Answer : The answer is 'Decreased'

When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Description : When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Last Answer : answer:

When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Description : When temperature is gradually decreased, what is the specific heat of substance? -General Knowledge

Last Answer : answer:

Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (C) Gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (D) None of these

Description : Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the ... specified amount at the junction of the transition curve with main curve (D) None of these

Last Answer : (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve

For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Description : For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Last Answer : (D) All the above

A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in volume during test, is not possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Description : A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in ... possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Last Answer : Answer: Option A

If the surface of liquid is convex, men (A) Cohesion pressure is negligible (B) Cohesion pressure is decreased (C) Cohesion pressure is increased (D) There is no cohesion pressure

Description : If the surface of liquid is convex, men (A) Cohesion pressure is negligible (B) Cohesion pressure is decreased (C) Cohesion pressure is increased (D) There is no cohesion pressure

Last Answer : Answer: Option C

Gradually varied flow in open channel is a/an __________ flow. (A) Steady uniform (B) Steady non-uniform (C) Unsteady uniform (D) Unsteady non-uniform

Description : Gradually varied flow in open channel is a/an __________ flow. (A) Steady uniform (B) Steady non-uniform (C) Unsteady uniform (D) Unsteady non-uniform

Last Answer : (B) Steady non-uniform

Gradually varying fluid flow is an example of __________ flow. (A) Non-steady uniform (B) Non-steady non-uniform (C) Steady uniform (D) Steady non-uniform

Description : Gradually varying fluid flow is an example of __________ flow. (A) Non-steady uniform (B) Non-steady non-uniform (C) Steady uniform (D) Steady non-uniform

Last Answer : (A) Non-steady uniform

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Last Answer : (A) Zero

The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross-section of the shaft, which is plane before twist remains plane after twist (D) All radii get twisted due to torsion

Description : The following assumption is not true in the theory of pure torsion:  (A) The twist along the shaft is uniform  (B) The shaft is of uniform circular section throughout  (C) Cross- ... , which is plane before twist remains plane after twist  (D) All radii get twisted due to torsion 

Last Answer : (D) All radii get twisted due to torsion 

If a constant section beam is subjected to a uniform bending moment throughout, its length bends to (A) A circular arc (B) A parabolic arc (C) A catenary (D) None of these

Description : If a constant section beam is subjected to a uniform bending moment throughout, its length bends  to  (A) A circular arc  (B) A parabolic arc  (C) A catenary  (D) None of these 

Last Answer : (A) A circular arc 

A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Last Answer : (D) Bending stress is same at every section along its longitudinal axis

A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Deflection is same throughout the beam (C) Bending stress is same throughout the beam (D) Shear stress is same throughout the beam

Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Deflection is same throughout the beam (C) Bending stress is same throughout the beam (D) Shear stress is same throughout the beam

Last Answer : (C) Bending stress is same throughout the beam

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

Due to scan geometry of a satellite sensor: (A) The off-nadir resolution is degraded (B) The ground distance swept by the senor, IFOV is proportional to sec2 of scan measured from the nadir (C) The details towards the edge of the scan get compressed (D) All of these

Description : Due to scan geometry of a satellite sensor: (A) The off-nadir resolution is degraded (B) The ground distance swept by the senor, IFOV is proportional to sec2 of scan measured from the nadir (C) The details towards the edge of the scan get compressed (D) All of these

Last Answer : Answer: Option D

In highway construction on super-elevated curves, the rolling shall proceed from (A) Sides towards the centre (B) Centre towards the sides (C) Lower edge towards the upper edge (D) Upper edge towards the lower edge

Description : In highway construction on super-elevated curves, the rolling shall proceed from (A) Sides towards the centre (B) Centre towards the sides (C) Lower edge towards the upper edge (D) Upper edge towards the lower edge

Last Answer : Answer: Option C