Description : The neutral axis of an over –reinforced section falls (a) On the critical neutral axis of balanced section. (b) Below the critical neutral axis of balanced section (c) Above the neutral axis o balanced section (d) Al l the above
Last Answer : (b) Below the critical neutral axis of balanced section
Description : The actual neutral axis of n under reinforced section is above the critical neutral axis of a balanced section (a) Correct (b) Incorrect (c) Not known (d) None of these
Last Answer : (a) Correct
Description : The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than
Last Answer : [ A ] equal
Description : The neutral axis corresponding to balanced section condition is termed as [ A ] Critical neutral axis [ B ] Centroidal neutral axis [ C ] Balanced neutral axis [ D ] All the above
Last Answer : [ A ] Critical neutral axis
Description : If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above
Last Answer : Option C
Description : With usual notations the depth of the neutral axis of a balanced section, is given by (A) mc/t = (d - n)/n (B) t/mc = (d - n)/n (C) t/mc = (d + n)/n (D) mc/t = n/(d - n)
Last Answer : Answer: Option D
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Last Answer : Answer: Option B
Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.
Last Answer : both b&c
Description : The section of the beam having greater width at the top in comparison to the width below neutral axis is known as. (a) Critical section (b) T-section (c) L-section (d) None of these
Last Answer : (b) T-section
Description : The depth of neutral axis for over reinforced section is ----------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above
Last Answer : [ B ] Greater than
Description : The depth of neutral axis for under reinforced section is --------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above
Last Answer : [ C ] Less than
Description : If the depth of actual axis in a beam is more than the depth of critical axis, then the beam is called (a) Over reinforced beam (b) Under-reinforced beam (c) Balanced beam (d) Deep beam
Last Answer : (a) Over reinforced beam
Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above
Description : In a singly reinforced beam, if the permissible stress in steel reaches earlier than that of concrete, the beam section as called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section
Last Answer : [ A ] Under reinforced section
Description : In a Singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section
Last Answer : [ B ] Over reinforced section
Description : The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ D ] i, ii and iii
Description : In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section
Last Answer : (b) Over-reinforced section
Description : The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section
Last Answer : (a) Under-reinforced section
Description : In a beam section, if the steel reinforcement is of such a magnitude that the permissible stresses in concrete and steel are developed simultaneously, the section is. (a) Balanced section (b) Economical section (c) Critical section (d) All the above
Last Answer : (d) All the above
Description : In a doubly-reinforced beam if and is the effective depth and is depth of critical neutral axis, the following relationship holds good (A) mc/t = n/(d - n) (B) (m + c)/t = n/(d + n) (C) (t + c)/n = (d + n)/n D) mc/t = (d - n)/t
Last Answer : Answer: Option A
Description : If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is (A) [m/(m - r)] d (B) [m/(m + r)] d (C) [(m + r)/m] d (D) [(r - m)/m] d
Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above
Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above
Description : If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above
Last Answer : [ A ] Concrete attains its permissible stress earlier
Description : Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of equal area (D) All the above
Last Answer : (D) All the above
Description : The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at the neutral axis, is (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A
Last Answer : (C) 3F/2A
Description : Pick up the correct statement from the following: (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres (B) The shear stress is zero at the outer ... (C) The bending stress at the outer fibres, is known as principal stress (D) All the above
Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F
Last Answer : (C) M/I = E/R = E/Y
Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section
Last Answer : (B) Depth of the neutral axis
Description : The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these
Last Answer : (A) Pass through the centroid of the section
Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section
Last Answer : (B) Top fibre
Description : The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to (A) r (B) 1/r (C) r2 (D) 1/r²
Last Answer : (A) r
Description : If is the shear force at a section of an I-joist, having web depth and moment of inertia about its neutral axis, the difference between the maximum and mean shear stresses in the web is, (A) Sd²/8I (B) Sd²/12I (C) Sd²/16I (D) Sd²/24I
Last Answer : (D) Sd²/24I
Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section
Last Answer : (D) Algebraic sum of the transverse forces of the section
Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis
Description : For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis
Last Answer : Answer: Option C
Description : The neutral axis in a T-beam section falls (a) Within the flange (b) Outside the flange (c) Either (a) or (b) (d) All the above
Last Answer : (c) Either (a) or (b)
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange
Last Answer : c. neutral axis of the section
Description : Maximum shear stress in a triangular section ABC of height H and base B occurs at _________ a. H b. H/2 c. H/3 d. neutral axis
Last Answer : b. H/2
Description : What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above
Last Answer : a. 2.66 (S/bh)
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2
Description : Define section modulus and neutral axis.
Last Answer : Section Modulus: It is the ratio of M. I. of the section about the neutral axis and the distance of the most extreme fiber from the neutral axis. Neutral Axis: It is the axis shown in cross ... The intersection of the neutral layer with any normal cross section of a beam is called as neutral axis.
Description : Steel Beam theory is a method of designing [ A ] Balanced sections [ B ] Critical sections [ C ] Singly reinforced beams [ D ] Doubly reinforced beams
Last Answer : [ D ] Doubly reinforced beams
Description : According to Whitney's theory, depth of stress block for a balanced section of a concrete beam is limited to (A) 0.43 d (B) 0.537 d (C) 0.68 d (D) 0.85 d Where d is effective depth of beam
Description : According to ISI recommendations, the maximum depth of stress block for balanced section of a beam of effective depth d is (A) 0.43 d (B) 0.55 d (C) 0.68 d (D) 0.85 d
Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3
Last Answer : 1,2,4
Description : For a balanced section, the moment of resistance obtained from compressive force will be ___________the moment of resistance obtained from the tensile force (a) Greater than (b) Less than (c) Equal to (d) None of these
Last Answer : (c) Equal to
Description : For an over -reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal ... c) The maximum stress developed by steel will be equal to the allowable (d) All the above
Last Answer : (b) The maximum stress developed by concrete will be equal to allowable stress in concrete