Description : How do you service a cooling tower? • Ensure Proper Airflow. . Clean Your Tubes. • Inspect the Water Pump. • All of above
Last Answer : all of above
Description : What is the reason to service a cooling tower? a) to ensure proper air flow b) to clean the tubes c) to inspect the water pump d) all of these
Last Answer : all of these
Description : How is water circulated throughout the dry cooling tower system? a. Finned tubes b. Metal pipes c. Porous tubes d. Swifting tubes
Last Answer : a. Finned tubes
Description : How is water circulated throughout the dry cooling tower system? A] Finned tubes. B] Metal pipes C] Porous tubes. D] Swirling tubes
Last Answer : A] Finned tubes.
Description : Which among the following are the components of natural draft cooling tower a) Supply basin b) reinforced concrete c) Hot water distribution d) none of the above
Last Answer : reinforced concrete
Description : The ratio of dissolved solids in circulating water to the dissolved solids in makeup water is called a) Liquid gas ratio b) Cycle of concentration c) Cooling tower effectiveness d) None of the above
Last Answer : Cycle of concentration
Description : Which one of the following is true to estimate the range of cooling tower? a) Range = cooling water inlet temperature - wet bulb temperature b) Range = cooling water outlet temperature - wet bulb temperature ... = heat load in kcal per hour / water circulation in lines per hour d) None of the above
Last Answer : Range = heat load in kcal per hour / water circulation in lines per hour
Description : In which system is Cooling of hot water is done on tray as step by? a) Mechanical draught cooling system b) Hyperbolic cooling tower c) Atmospheric cooling tower d) Wet cooling tower
Last Answer : Atmospheric cooling tower
Description : Which of the following is the simplest method of cooling the condenser water? • Spray cooling pond • Cooling tower • Indirect air cooling • Hyperbolic cooling tower
Last Answer : Spray cooling pond
Description : In which system is Cooling of hot water is done on tray as step by? a. Mechanical draught cooling system b. Hyperbolic cooling tower c. Atmospheric cooling tower d. Wet cooling tower
Description : L/G ratio in a cooling tower is a ratio of _____. • Length and girth • Length and temperature gradient • Water flow rate and air mass flow rate • Air mass flow rate and water flow rate
Last Answer : Water flow rate and air mass flow rate
Description : The ratio of dissolved solids in circulating water to dissolved solids in makeup water is called. • Liquid gas ratio • Cycle of concentration • Cooling tower effectiveness • None of the above
Description : The ……….-induced response of cooling tower is the key factor to improve safety and to reduce tower crack. a) wind c) heat b) water d) steam
Last Answer : wind
Description : . In which system is Cooling of hot water is done on tray as step by? a) Mechanical draught cooling system b) Hyperbolic cooling tower c) Atmospheric cooling tower d) Wet cooling tower
Description : In ________ cooling tower there is no direct contact between the water and Air. • Dry type • Evaporative type • Once through • All of the above
Last Answer : All of the above
Description : The pollutants that are present depend on __________ building material, as well. • Cooling tower • Water tower • Steam tower • Fire tower
Last Answer : cooling water
Description : . How can we increase the efficiency of a cooling tower? a. Save energy. b. Reduce the amount of water being consumed. c. Decrease the amount of chemicals required for water treatment. d. All of above
Last Answer : All of above
Description : A ______ is a specialized heat exchanger in which air and water are brought into direct contact with each otherin order to reduce the water's temperature. a. Cooling tower b. Heating tower c. Both d. All are wrong
Last Answer : cooling tower
Description : How can we increase the efficiency of a cooling tower? a. Save energy. b. Reduce the amount of water being consumed. c. Decrease the amount of chemicals required for water treatment. d. All of above
Last Answer : d. All of above
Description : Pollution caused by cooling tower includes 1. Fouling 2. Limestone formation 3. Corrosion 4. All of above
Description : In hyperboloid cooling towers the material is filled at 1. Tower’s bottom 2. Tower’s top 3. Near tower 4. None of above
Last Answer : Tower’s top
Description : In the natural draft cooling tower_________ is not required a) Fan b) tower c) Nozzle d) none of the above
Last Answer : Fan
Description : In natural draft cooling tower the air flow is obtained by___________ a) Difference in air pressure b) difference in air temperature c) Difference in air speed d) none of the above
Last Answer : Difference in air pressure
Description : Cooling tower is a ______device a) Heat absorption b) heat rejection c) Both a and b c) neither a nor b
Last Answer : heat rejection
Description : Cooling tower effectiveness is the ratio of a) Range/( Range + approach) b) Approach/(range + approach) c) Range /(range - approach) d) Approach/ /(range - approach)
Last Answer : Range/( Range + approach)
Description : Natural draft cooling tower are mainly used in a) Steel Industry b) Alumina industry c) Fertilizer industry d) Power station
Last Answer : Power station
Description : How is air produced in mechanical draught cooling tower? a) Air Tuyeres b) Propeller fans c) Air blowers d) Louvre
Last Answer : Propeller fans
Description : The first hyperbolic cooling tower was built in... a. 1916 b. 1917 c. 1918 d. 1919
Last Answer : 1918
Description : Normally the guaranteed best approach a cooling tower can achieve is _____. • 5°C • 12°C • 8°C • 2.8°C
Last Answer : 2.8°C
Description : Cooling tower effectiveness is the ratio of _____. • Range/(range + approach) • Approach/(range + approach) • Range/ Approach • Approach/ Range
Last Answer : Range/(range + approach)
Description : A better indicators for cooling tower performance is _____. • Wet bulb temperature • Dry bulb temperature • Range • Approach
Last Answer : Approach
Description : Cooling efficiency of a cooling tower is significantly affected under cross-wind condition and might decrease to……… in the range of moderate to high wind velocity condition. a) 50% c) 25% b) 75% d) 90%
Last Answer : 75%
Description : The first hyperboloid shaped cooling tower was introduced by the Dutch engineers Frederik van Iterson andGerard Kuypers and built in ……….. a) 1918 c) 1919 b) 1870 d) 1920
Description : Which of the following faction affect the cooling tower performance? • The range • Heat load • Wet bulb temperature • All of the above
Description : In cooling tower ,higher temperature __________ corrosion potential • Decrease • Increase • Temperature has no effect on corrosion
Last Answer : Increase
Description : When sizing a cooling tower the highest anticipate__________ should be used? • Dry bulb • Wet bulb • Both dry and wet bulb • None of the above
Last Answer : Wet bulb
Description : Who do I call to inspect and clean a chimney?
Last Answer : Who do I call to inspect and clean a chimney?
Description : How to Inspect Gantry Cranes in Regular Service?
Last Answer : Gantry cranes are mostly designed to lift extremely heavyobjects and are very powerful machines. Almost always, they come inmassive sizes. Any malfunction can lead to serious injuries anddamages. Frequent ... noises, as wells as vibrations, andthe overall functioning of the gantry.2. Make sure
Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film coefficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'
Last Answer : (D) All 'a', 'b' & 'c'
Description : Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)? (A) Aluminium (B) Copper (C) Titanium (D) Stainless steel
Last Answer : Option C
Description : Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump
Last Answer : b. Economizer
Description : The bank of tubes at the back of domestic refrigerator are (a) condenser tubes (b) evaporator tubes (c) refrigerant cooling tubes (d) capillary tubes
Last Answer : Ans: a
Description : How the heat dissipation is improved by providing the cooling tubes?
Last Answer : The cooling tubes will improve the circulation of oil. The circulation of oil is due to effective pressure heads produced by columns of oil in tubes. The improvement in cooling is accounted by taking the specific heat dissipation due to convection as 35% more than that without tubes.
Description : Why cooling tubes are provided?
Last Answer : Cooling tubes are provided to increase the heat dissipating area of the tank.
Description : The bank of tubes located at the back of the domestic refrigerators are the __________ tubes. (A) Refrigerant cooling (B) Evaporator (C) Condenser (D) Throttling
Last Answer : C) Condenser
Description : The haemodialyzer has semi-permeable lining of tubes which help to: (a) To maintain osmotic pressure of blood. (b) To filter nitrogenous wastes from the dialyzing solution. (c) In passing the waste product, in the dialyzing solution. (d) To pump purified blood back into the body of the patient.
Last Answer : (c) In passing the waste product, in the dialyzing solution.
Last Answer : The cause of wind flow is diurnal motion.
Last Answer : Airflow causes cyclones.
Description : What is the layer that is the airflow directly next to rocket skin?
Last Answer : What is the answer ?
Description : How do you tell if you mass airflow sensor is faulty?
Last Answer : There are several ways to check your mass airflow sensor. You can measure the output voltage of the sensor, measure the hot film frequency of the sensor, or check the self-cleaning circuit. eHow has a great article that elaborates on these steps.