Description : In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a
Last Answer : ans a
Description : The plough bottom as combined unit consist of: a) None of these c) Coulter , jointer and frog b) Beam , handle and MB d) Share, landside , frog and MB
Last Answer : Share, landside , frog and Mb
Description : The draft requirement in MB plough compared to disc plough for same depth of ploughing is: a) Less c) More b) Equal d) None of these
Last Answer : More
Description : During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a
Description : The adjustment in MB plough for increasing the depth of operation a) Vertical suction b) Horizontal suction c) Gang angle d) Disc angle Ans. a
Description : Vertical section of plough influences 1. Pulverization 2. Depth of cut 3. Width of cut 4. direction of pull
Last Answer : ans 2
Description : Vertical section of plough influences A. Pulverization C. Width of cut B. Depth of cut D. Direction of pull
Last Answer : Depth of cut
Description : Stubble bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. a
Description : Sod bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. b
Last Answer : ans b
Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel
Last Answer : d) Soft centre steel
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : The two primary tillage equipments are 1. MB and disc harrow 2. Disc plough and disc harrow 3. Disc harrow and cultivator 4. MB and subsoiler
Last Answer : ans 4
Description : Dead furrow is made by 1. One way MB plough 2. 2 way MB plough 3. ridger 4. disc harrow
Last Answer : ans 1
Description : The two primary tillage equipments are A. MB and disc harrow B. Disc plough and disc harrow C. Disc harrow and cultivator. D. MB and. Subscriber
Last Answer : MB and disc harrow
Description : Dead furrow is made by A. One way MB plough. B. 2 way MB plough C. Ridger. D. Disc harrow
Last Answer : One way MB plough
Description : Jointer and coulter are the parts of :- A. Disc plough C. Indigenous plough B. Harrow plough D. MB plough
Last Answer : MB plough
Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above
Last Answer : D. All of the above
Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above
Last Answer : d) All the above
Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil
Last Answer : b) Suitability for pudding paddy field
Description : Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a
Description : Ridger is also known as riding plough and moulds board plough. a. Single c. Half d. None of the above. Ans - b. Double
Last Answer : Ans - b. Double
Description : pressure should be less in rear wheel as compare to front wheel because of a) high traction b) low draft c) high draft d) none of these Ans. a
Description : Find the odd mean out a. Share. c) body b. Shoe. d) Landside
Last Answer : Landside
Description : A boy and his dad put a rope around a tree and stand side by side. What force by the boy can resist a force of 800 N by the dad? a.231 b.246 c.192 d.107 dynes e.166
Last Answer : e. 166
Description : A mould board of MB plough is made of? a Cast iron b Chilled cast iron c Mild steel d Soft centre steel
Last Answer : d Soft centre steel
Description : For maximum moisture conservation ploughing is done with A. mb plough b. cultivator c. chisel plough d. dice harrow
Last Answer : c. chisel plough
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Does it take MB to run Ans Bangla ?
Last Answer : Yes, of course it takes MB. You can't drive for free.
Description : How to run Ans Bangla completely free i.e. without any MB or money ?
Last Answer : Ans Bangla Free Basic does not exist so it cannot be run for free at this moment. However, Free Basic will be added very soon. Then you can use it for free.
Description : The truss element can resist only a.surface force b.axial force c.point load d.none of the above
Last Answer : b.axial force
Description : A truss element a.107 dynes b.resists lateral forces c.is a two-force body d.is a three force body e.resist forces in compression only
Last Answer : c. is a two-force body
Description : The draft of ‘Victory plough’ is— (A) 80-100 kg (B) 40-50 kg(C) 70-80 kg (D) 10-20 kg
Last Answer : (A) 80-100 kg
Description : 1Heavy draft of a disc plough is due to: A. Blunt disc B. Furrows too wide C. Loose bearings D. All are currect
Last Answer : D. All are currect
Description : Heavy draft of a disc plough is due to: a) Blunt disc b) Furrows too wide c) Loose bearings d) All of the above
Last Answer : d) All of the above
Description : It is that part of the plough bottom which penetrates into the soil and makes a horizontal cut below the surface. a. Land side c. body d. None of the above
Last Answer : Ans – b. Share
Description : is not component of M.B. Plough a) Share. c) Land side b) Shoe. d) Tail piece
Last Answer : Shoe.
Description : is the component of mold board plough. a) Land side b) Soil c) Both a & b d) None
Last Answer : Land side
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : Functions of mold board plough a. Cutting the furrow slice. c) body to yoke b. Increase the depth of operation. d) length of the beam
Last Answer : Cutting the furrow slice.
Description : Select the function of Moldboard plough. a) Lifting the soil. c) Pulverizing the soil b) Cutting the furrow slice d) All of the above
Last Answer : All of the above
Description : The function of scraper is to . a) Remove soil stuck to the disc b) Provide support to the disc c) Used for holding plough d) None of the above
Last Answer : Remove soil stuck to the disc
Description : is the function of mold board plough. a) Cutting the furrow slice b) Lifting the soil c) Pulverizing the soil d) All of the above
Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on
Last Answer : ANSWER : B
Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft
Last Answer : a)pull
Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient
Last Answer : (C) Increase the shell side heat transfer co-efficient