pressure should be less in rear wheel as compare to front wheel because of a) high traction b) low draft c) high draft d) none of these Ans. a

pressure should be less in rear wheel as compare to front wheel because of a) high traction b) low draft c) high draft d) none of these Ans. a
by

1 Answer

Answer :

ans a
by

Related questions

pressure should be high in front wheel of the tractor because of a) high slippage b) low slippage c) high traction d) easy steer ability Ans. d

Description : pressure should be high in front wheel of the tractor because of a) high slippage b) low slippage c) high traction d) easy steer ability Ans. d

Last Answer : ans d

The traction on rear wheels can be increased by increasing a) Weight on rear wheels b) Weight on front wheels c) Decreasing inflation pressure d) Both a and c Ans. d

Description : The traction on rear wheels can be increased by increasing a) Weight on rear wheels b) Weight on front wheels c) Decreasing inflation pressure d) Both a and c Ans. d

Last Answer : ans d

In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a

Description : In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a

Last Answer : ans a

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a

Description : During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a

Last Answer : ans a

Differential lock in tractor is used to improve a) Lateral stability b) Braking performance c) Hydraulic lift d) Traction of a wheel

Description : Differential lock in tractor is used to improve a) Lateral stability b) Braking performance c) Hydraulic lift d) Traction of a wheel

Last Answer : Braking performance 

Differential lock in tractor is used to improve a) Lateral stability b) Braking performance c) Hydraulic lift d) Traction of a wheel

Description : Differential lock in tractor is used to improve a) Lateral stability b) Braking performance c) Hydraulic lift d) Traction of a wheel

Last Answer : ans d

Shortening of top link of tractor three-point hitch system a) Increases weight transfer on rear wheels b) Decreases weight transfer on rear wheels c) Increases penetration of implement d) Decreases penetration of implement Ans. d

Description : Shortening of top link of tractor three-point hitch system a) Increases weight transfer on rear wheels b) Decreases weight transfer on rear wheels c) Increases penetration of implement d) Decreases penetration of implement Ans. d

Last Answer :  Ans. d

Is my 2016 Chrysler Town and Country front or rear wheel drive?

Description : Is my 2016 Chrysler Town and Country front or rear wheel drive?

Last Answer : A 2016 Chrysler Town and Country is front wheel drive.

Front and rear wheel axle bearings may be washed and replaced once in a) four years b) three years c) two years d) one year

Description : Front and rear wheel axle bearings may be washed and replaced once in a) four years b) three years c) two years d) one year

Last Answer : d) one year

Handbrake is applicable to A. Only front wheels B. Only rear wheels C. Both front and rear wheel. D. All of the above.

Description : Handbrake is applicable to A. Only front wheels B. Only rear wheels C. Both front and rear wheel. D. All of the above.

Last Answer : B. Only rear wheels

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

The function of landside in mb plough is to a) Resist the side draft force b) Increase pulverization c) Decrease draft d) All of these Ans. a

Description : The function of landside in mb plough is to a) Resist the side draft force b) Increase pulverization c) Decrease draft d) All of these Ans. a

Last Answer : ans a

The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above

Description : The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above

Last Answer : rear 

Natural Draft or Hyperbolic towers have been used for • Large Capacity of water • Small Capacity of Water • High Efficiency • Low capital cost

Description : Natural Draft or Hyperbolic towers have been used for • Large Capacity of water • Small Capacity of Water • High Efficiency • Low capital cost

Last Answer : Large Capacity of water

The car has a locked rear wheel.

Description : The back wheel of the Favorit has blocked and is not moving.

Last Answer : Take a log about 30 cm long with a diameter of 2-3 cm. (eg a long extension from the Gola set) Lean it against the brake drum through a hole in the disc and tap it with a larger hammer. ... The brake will release at 90 percent. All this on a car with the parking brake enabled and number one engaged.

Explain Bicycle Rear Wheel Sprocket Working?

Description : Explain Bicycle Rear Wheel Sprocket Working?

Last Answer : Rear wheel sprocket works under the principle of ratchet and pawl.

The draft requirement in MB plough compared to disc plough for same depth of ploughing is: a) Less c) More b) Equal d) None of these

Description : The draft requirement in MB plough compared to disc plough for same depth of ploughing is: a) Less c) More b) Equal d) None of these

Last Answer : More

The nature of loading at various locations and other surfaces conditions called a.friction b.traction c.boundary condition d.surfacing

Description : The nature of loading at various locations and other surfaces conditions called a.friction b.traction c.boundary condition d.surfacing

Last Answer : c.boundary condition

The art of subdividing the structure into a convenient number of smaller elements is knownas a.discretization b.assemblage c.continuum d.traction

Description : The art of subdividing the structure into a convenient number of smaller elements is knownas a.discretization b.assemblage c.continuum d.traction

Last Answer : a.discretization

Hyperbolic cooling towers have become design standard for all natural draft structural towers because usage of . a. Their structural strength b. Minimum usage of material. c. Improving cooling efficiency d. All of the above.

Description : Hyperbolic cooling towers have become design standard for all natural draft structural towers because usage of . a. Their structural strength b. Minimum usage of material. c. Improving cooling efficiency d. All of the above.

Last Answer : All of the above.

__________ Cooling towers have become the design standard for all natural-draft cooling towers because oftheir structural strength and minimum usage of material. • HCT • CCT • Hyperboloid • None

Description : __________ Cooling towers have become the design standard for all natural-draft cooling towers because oftheir structural strength and minimum usage of material. • HCT • CCT • Hyperboloid • None

Last Answer : Hyperboloid

Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Description : Differential lock offers advantage of A. Better drawbar pull when drive wheel are under different conditions B. Easier to plant in straight rows C. Reduces stearing effort and side draft when operating with certain implements D. All of the above

Last Answer : D. All of the above

position in tractor is allows you to rest the bucket on the ground without down pressure or lift A. Boat. C. Draft control B. Float. D. None of the above

Description : position in tractor is allows you to rest the bucket on the ground without down pressure or lift A. Boat. C. Draft control B. Float. D. None of the above

Last Answer : Float.

In natural draft cooling tower the air flow is obtained by___________ a) Difference in air pressure b) difference in air temperature c) Difference in air speed d) none of the above

Description : In natural draft cooling tower the air flow is obtained by___________ a) Difference in air pressure b) difference in air temperature c) Difference in air speed d) none of the above

Last Answer : Difference in air pressure

In a sprayer overlapping can be increased by increasing a) Nozzle diameter b) Pressure c) Discharge d) Height of nozzle Ans. d

Description : In a sprayer overlapping can be increased by increasing a) Nozzle diameter b) Pressure c) Discharge d) Height of nozzle Ans. d

Last Answer : ans d

When I box up my bike to ship, do I have to remove the front and rear racks?

Description : When I box up my bike to ship, do I have to remove the front and rear racks?

Last Answer : I would look for info on that with the shipping service you’ll use.

why does adjusting the camber in the front and rear of your car enable race tires to last longer? I race a Porsche 911 and am hearing differing things about the benifits of camber settings.

Description : why does adjusting the camber in the front and rear of your car enable race tires to last longer? I race a Porsche 911 and am hearing differing things about the benifits of camber settings.

Last Answer : race tires are usually made of a softer rubber than normal street tires to enable better traction. changing the camber changes the weight distribution of the vehicle over the tire - and given that the ... sure that the right amount of pressure is being put on the tire to prevent uneven wear...

Do Front air bags are not designed to offer protection from crashes from the rear and side?

Description : Do Front air bags are not designed to offer protection from crashes from the rear and side?

Last Answer : What is the answer ?

What states require front & rear license plate installation on cars?

Description : What states require front & rear license plate installation on cars?

Last Answer : All states EXCEPT: Alabama, Arizona, Arkansas, Delaware, Florida, Georgia, Indiana, Kansas, Kentucky, Louisiana, Michigan, Mississippi, New Mexico, North Carolina, Oklahoma, Pennsylvania, South Carolina, Tennessee, and West Virginia

Is a front or rear window tint illegal anywhere in the United States?

Description : Is a front or rear window tint illegal anywhere in the United States?

Last Answer : Front windows tint is illegal is most states in the US. You can though get a permit that allows it with a prescription from a doctor saying you have sensitive eyes. See the website http://home ... in some of the states in the United States. Such states include Chicago, New York and Massachusetts.

how much would it cost to replace the front brake pads and rear drums on a 2001 honda odesey?

Description : how much would it cost to replace the front brake pads and rear drums on a 2001 honda odesey?

Last Answer : You have to make at least enough to pay your portion of the rent when you are on Section 8. But you cannot make no more than $28,250 for a family of four to remain on the program.

Whats the cost to replace front and rear brakes on a 2017 chevy sonic?

Description : Whats the cost to replace front and rear brakes on a 2017 chevy sonic?

Last Answer : Search Results Featured snippet from the web Chevrolet Sonic Brake Rotors/Discs Replacement costs $329 on average. Car Service Estimate 2017 Chevrolet SonicL4-1.8L Service typeBrake Rotor/Disc - ... 2017 Chevrolet SonicL4-1.4L Turbo Service typeBrake Rotor/Disc - Front Replacement Estimate$413.07

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

Hand brake is applicable to (A) only front wheels (B) only rear wheels (C) both front and rear wheels (D) all of the above

Description : Hand brake is applicable to (A) only front wheels (B) only rear wheels (C) both front and rear wheels (D) all of the above

Last Answer : (B) only rear wheels

A train travelling at a speed of 75 mph enters a tunnel 7/2 miles long. The train is 1/4 mile long. How long does it take for the train to pass through the tunnel from the moment the front enters to the moment the rear emerges? A.1 min B.3 min C.5 min D.6 min E.None of these

Description : A train travelling at a speed of 75 mph enters a tunnel 7/2 miles long. The train is 1/4 mile long. How long does it take for the train to pass through the tunnel from the moment the front enters to the moment the rear emerges? A.1 min B.3 min C.5 min D.6 min E.None of these

Last Answer : Answer – B (3 min) Explanation – Actually train is covering length of tunnel + its own length here so total distance = 7/2 + 1/4= 15/4 miles time= distance /speed time= (15/4) / 75 = 1/20 hour (1/20)x60 = 3 min

Which Bus connects CPU & level 2 cache: a. Rear side bus b. Front side bus c. Memory side bus d. None of these

Description : Which Bus connects CPU & level 2 cache: a. Rear side bus b. Front side bus c. Memory side bus d. None of these

Last Answer : b. Front side bus

With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is shackled and the rear end is pin joined (c) both end of the spring are shackled (d) both end of the spring are pin joined

Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined

Last Answer : (b) front end of the spring is shackled and the rear end is pin joined

Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of the disc harrow penetrates deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front

Last Answer : a) Concave

The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links

Last Answer : d) Between two lower links

Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Description : Blades of disc harrow are sharpened from the_______ side penetrate more readily than blades sharpened from the__________ side a) convex, concave c) concave, convex b) Front, rear d) Rear, front

Last Answer : c) concave, convex

If the queue is implemented with a linked list, keeping track of a front pointer and a rear pointer, which of these pointers will change during an insertion into a non-empty queue? (A) Neither of the pointers change (B) Only front pointer changes (C) Only rear pointer changes (D) Both of the pointers changes

Description : If the queue is implemented with a linked list, keeping track of a front pointer and a rear pointer, which of these pointers will change during an insertion into a non-empty queue? (A) Neither of ... (B) Only front pointer changes (C) Only rear pointer changes (D) Both of the pointers changes

Last Answer : (C) Only rear pointer changes

is not component of seed drill. a) Pressure regulator b) Frame c) Seed box d) Transport wheel

Description : is not component of seed drill. a) Pressure regulator b) Frame c) Seed box d) Transport wheel

Last Answer : Pressure regulator

In ……levelling board is attached to the rear side of the unit for levelling the tilled soil. a. Disc b. Mould board d. None of the above

Description : In ……levelling board is attached to the rear side of the unit for levelling the tilled soil. a. Disc b. Mould board d. None of the above

Last Answer : Ans - c. Rotary tiller

Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Description : Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Last Answer : (B) Backward curved

The draft of a trailed type implement can be measured using a) Brake dynamometer b) Torque meter c) Tension dynamometer d) Dial gauge

Description : The draft of a trailed type implement can be measured using a) Brake dynamometer b) Torque meter c) Tension dynamometer d) Dial gauge Ans. c

Last Answer : Ans. c

Notched disc blades on disc harrows are provided to a) Enhance penetration b) Improve balancing of gangs c) Save on steel d) Reduce draft

Description : Notched disc blades on disc harrows are provided to a) Enhance penetration b) Improve balancing of gangs c) Save on steel d) Reduce draft

Last Answer : ans a

Model registration fee payment can be done by... a. Demand draft c. Cash b. Online d. Both a & b

Description : Model registration fee payment can be done by... a. Demand draft c. Cash b. Online d. Both a & b

Last Answer : Both a & b