Description : Sod bottom mold board is used where a) Pulverization is needed b) Inversion is needed c) Both d) None of these Ans. b
Last Answer : ans b
Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom
Last Answer : b. General bottom
Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom
Last Answer : b. sod bottom
Description : The function of landside in mb plough is to a) Resist the side draft force b) Increase pulverization c) Decrease draft d) All of these Ans. a
Last Answer : ans a
Description : The slat type mold board is used in a) Sticky soil b) Hard soil c) Loose soil d) Stoney and trashy soil Ans. a
Description : Rotary tiller are wide adopted in rice cultivation due to a) Excessive pulverization b) Suitability for pudding paddy field c) Reduced draft requirement d) Complete inversion of soil
Last Answer : b) Suitability for pudding paddy field
Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom
Last Answer : a. Sod bottom
Description : is the component of mold board plough. a) Land side b) Soil c) Both a & b d) None
Last Answer : Land side
Description : Vertical section of plough influences 1. Pulverization 2. Depth of cut 3. Width of cut 4. direction of pull
Last Answer : ans 2
Description : Vertical section of plough influences A. Pulverization C. Width of cut B. Depth of cut D. Direction of pull
Last Answer : Depth of cut
Description : Ridger is also known as riding plough and moulds board plough. a. Single c. Half d. None of the above. Ans - b. Double
Last Answer : Ans - b. Double
Description : This type mould boars plough is used for sticky soil. b. Sod or breaker c. Stubble d. None of the above
Last Answer : Ans –a. Slat type
Description : This type mould boards plough is used for tough soil of grasses. a. slat c. Stubble d. None of the above
Last Answer : Ans- b. Sod or breaker
Description : Moldboard consists of following types : a) General purpose. c) Sod or breaker b) Stubble. d) All of the above
Last Answer : All of the above
Description : turns the furrow slice used in stubble soils. a) Stubble type b) Slat type c) Share d) Jointer
Last Answer : <!-- [endif] -->Stubble type
Description : is the general purpose lying. a) Between stubble and sod b) Between soil and mud c) Between man and machine d) None
Last Answer : <!-- [endif] -->Between stubble and sod
Description : are the types of moldboards. a) General purpose b) Stubble c) Slat d) All of above
Last Answer : all of above
Last Answer : All of above
Description : Functions of mold board plough a. Cutting the furrow slice. c) body to yoke b. Increase the depth of operation. d) length of the beam
Last Answer : Cutting the furrow slice.
Description : Components of mold board plough a. Share. c) forg b. Mould board. d) All of the above
Description : Ploughs used to break through shatter compacted or imperable soil layers. a) Disc plough b) Mold board plough c) Chisel plough d) Country plough
Last Answer : Chisel plough
Description : is the function of mold board plough. a) Cutting the furrow slice b) Lifting the soil c) Pulverizing the soil d) All of the above
Description : What is the bottom note in a first inversion triad?
Last Answer : In 1st inversion, the 3rd of the chord is on the bottom. For theexample of C major, the E is the lowest note.
Description : The radiation emitted by a body as a result of its temperature. a. Blackbody Radiation b. Thermal Inversion c. Thermionic Inversion d. Thermal Radiation
Last Answer : Thermal Radiation
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above
Last Answer : D. All of the above
Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above
Last Answer : d) All the above
Description : The difference between seed drill and planter is a) Variation in hill to hill spacing b) Number of seed per hill is more uniform in planter c) Seed delivery tube d) Furrow opener e) Both a and b Ans. e
Last Answer : ans e
Description : The traction on rear wheels can be increased by increasing a) Weight on rear wheels b) Weight on front wheels c) Decreasing inflation pressure d) Both a and c Ans. d
Last Answer : ans d
Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b
Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a
Description : seed drill can be tested by a) sand bed method b) sticky belt methods c) both d) none of these Ans. c
Last Answer : ans c
Description : Seed drill uniformity can be measured by a) Number of seed per rotation of metering unit b) Spacing between seeds c) a and b both d) none of these Ans. c
Description : In tractor engine which of the following is a device in which liquid fuel is converted into gaseous fuel? 1. Piston 2. Carburetor 3. Both 1 and 2 4. none of these ans 1
Last Answer : ans 1
Description : Does anybody know how to get mold out of the bottom of a water bottle?
Last Answer : You need a bottle brush to thoroughly scrub them, or…you might try adding about a ¼ cup of salt, a wee bit of water and shake vigorously for scrubbing action. lol
Description : This is for those of you who shave down there... not wax. How do you get past the stubble?
Last Answer : I HATE shaving the bikini area… I use Nair. It’s far less painful growing back in for me.
Description : The tillage that is done immediately after crop harvesting to remove the weeds and to restore soil structure is? A. strip B. sub-soil C. fallow D. stubble
Last Answer : D. stubble
Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above
Last Answer : d)All of the above
Description : V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage
Last Answer : b) Stubble mulch tillage
Description : Uniformity measure of a planter is a) Equal seed spacing b) Equal number of seed dropped per hill c) Minimum variation in different openers d) All of the above Ans. d
Description : During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a
Description : The rotavator blade is generally operated at a) 180-320 rpm b) 450-1000 rpm c) 200 – 600 rpm d) None of these Ans. a
Description : The engine produces dark black smoke due to a) Burning of oil b) Due of incomplete combustion c) Due to moisture in fuel d) None of these Ans. b
Description : While increasing the forward speed of the combine harvester speed of reel should be a) Increased in same ratio b) Decreased in same ratio c) No changes d) Doubled Ans. a
Description : In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a
Description : The tillage pattern are a) Head land pattern b) Gathering c) Casting d) All of these Ans. d
Description : The battery has following three major functions to perform: a) To provide a source of current for engine starting, lighting and use of horn. b) To help control the voltage in the electrical system. c ... the current produced by dynamo/alternator and to furnish the current d) all of the above. Ans. d
Description : pressure should be high in front wheel of the tractor because of a) high slippage b) low slippage c) high traction d) easy steer ability Ans. d
Description : pressure should be less in rear wheel as compare to front wheel because of a) high traction b) low draft c) high draft d) none of these Ans. a