The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°) 
by

1 Answer

Answer :

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is 2 sin ωt 

by

Related questions

The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4.

Description : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be :  (A) 270° (B) 210° (C) 180° (D) 300°

Last Answer : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be : 210°

Lissajous pattern obtained on a CRO screen is a circle. Frequency of two signals are

Description : Lissajous pattern obtained on a CRO screen is a circle. Frequency of two signals are   (a) Equal (b) Unequal (c) Zero (d) Infinity 

Last Answer : a

The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a

Description : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with its major ... frequencies very close but not equal D) There is a constant but small phase difference between the signals

Last Answer : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with ... following inference can be made from this The signals are sinusoidal with their frequencies very close but not equal 

Consider the following statements with regard to Lissajous pattern on a CRO : 1. It is a stationary pattern on...

Description : Consider the following statements with regard to Lissajous pattern on a CRO :  1. It is a stationary pattern on the CRO.  2. It is used for precise measurement of frequency of a voltage signal.  3. The ratio between frequencies ... /are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

Last Answer : Consider the following statements with regard to Lissajous pattern on a CRO :  1. It is a stationary pattern on the CRO.  2. It is used for precise measurement of frequency of a voltage signal.  3. The ratio between ... /are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

The Lissajous pattern obtained on a CRO in used to determine:

Last Answer : The Lissajous pattern obtained on a CRO in used to determine: Phase shift and frequency

In a CRO which of the following is not a part of electron gun:

Description : In a CRO which of the following is not a part of electron gun: (1) Cathode (2) Grid (3) Accelerating anode (4) X–Y plates 

Last Answer : In a CRO which of the following is not a part of electron gun: X–Y plates 

Describe with suitable example; frequency measurement by Lissajous patterns on CRO.

Description : Describe with suitable example; frequency measurement by Lissajous patterns on CRO. 

Last Answer : * Initially the unknown frequency signal is connected to vertical deflection plates of CRO. * Now switch of the internal sweep generator of the horizontal deflecting system. * A standard source ... explain by following example: Assume horizontal input frequency is 10 kHz for following pattern

For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : d) Parabola

For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : (c) Line inclined to x-axis

For any part of a beam between two concentrated load, Bending moment diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam between two concentrated load, Bending moment diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : (c) Line inclined to x-axis

7-For any part of the beam, between two concentrated load Shear force diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : 7-For any part of the beam, between two concentrated load Shear force diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : Na

On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal. (A) Frequency (B) Amplitude (C) Damping (D) None of these

Description : On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal. (A) Frequency (B) Amplitude (C) Damping (D) None of these

Last Answer : (A) Frequency

A object moves with uniform positive acceleration. Its velocity-time graph will be (a) A straight line parallel to the time axis (b) A straight line inclined at an obtuse angle to the time axis (c) A straight line inclined at an acute angle to the time axis (d) None of these. -Science

Description : A object moves with uniform positive acceleration. Its velocity-time graph will be (a) A straight line parallel to the time axis (b) A straight line inclined at an obtuse angle to the time axis (c) A straight line inclined at an acute angle to the time axis (d) None of these. -Science

Last Answer : Answer is (c)

The locus of the moment of inertia about inclined axes to the principal axis, is (A) Straight line (B) Parabola (C) Circle (D) Ellipse

Description : The locus of the moment of inertia about inclined axes to the principal axis, is  (A) Straight line  (B) Parabola  (C) Circle  (D) Ellipse

Last Answer : (D) Ellipse

Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type (A) Parallel flow with equal heat capacities (B) Counter flow with equal heat capacities (C) Counter flow with unequal heat capacities (D) Parallel flow with unequal heat capacities

Description : Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type (A) Parallel flow with equal heat capacities (B) Counter ... (C) Counter flow with unequal heat capacities (D) Parallel flow with unequal heat capacities

Last Answer : (B) Counter flow with equal heat capacities

Explain measurement of phase and frequency using Lissajous pattern. Write the formula for each one.

Description : Explain measurement of phase and frequency using Lissajous pattern. Write the formula for each one.

Last Answer : Phase measurement of Lissajous pattern: The phase measurement can be done by using Lissajous figures. The CRO is set to operate in the X- Y mode, then the display obtained on the screen of a ... or sub- multiple of the unknown frequency.  The Lissajous pattern appears stationary.     

Define Lissajous pattern. Explain how Lissajous pattern is useful for frequency and phase measurement.

Description : Define Lissajous pattern. Explain how Lissajous pattern is useful for frequency and phase measurement.

Last Answer : Lissajous Pattern : The CRO is set to operate in the X- Y mode, when two sine waves of the same frequency are applied to the CRO (One vertical and one horizontal deflection plates) then the display obtained on ... 1. Lissajous pattern for ratio 3:1    2. Lissajous pattern for ratio 3:2  

A 7 years-old child has class I malocclusion, slight version of maxillary class III, adequate arch length. What is your management: A. Oral screen B. Head cap therapy C. Inclined plane on mandibular anterior teeth D. Hawley plate E. Expansion screw plate

Description : A 7 years-old child has class I malocclusion, slight version of maxillary class III, adequate arch length. What is your management: A. Oral screen B. Head cap therapy C. Inclined plane on mandibular anterior teeth D. Hawley plate E. Expansion screw plate

Last Answer : C. Inclined plane on mandibular anterior teeth

A member is balanced at its end by two inclined members carrying equal forces. For equilibrium the angle between the inclined bars must be (A) 3° (B) 45° (C) 90° (D) 120°

Description : A member is balanced at its end by two inclined members carrying equal forces. For equilibrium  the angle between the inclined bars must be  (A) 3°  (B) 45°  (C) 90°  (D) 120° 

Last Answer : (D) 120° 

A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of internal friction for the soil are respectively (A) 0.5 N/mm² and 30° (B) 0.05 N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Last Answer : Answer: Option B

The major principal stress in an element of cohesion-less soil within the backfill of a retaining wall is (A) Vertical if the soil is in an active state of plastic equilibrium (B) Vertical if the soil is in a passive state of plastic equilibrium (C) Inclined at 45° to the vertical plane (D) None of the above

Description : The major principal stress in an element of cohesion-less soil within the backfill of a retaining wall is (A) Vertical if the soil is in an active state of plastic equilibrium (B) Vertical if the ... state of plastic equilibrium (C) Inclined at 45° to the vertical plane (D) None of the above

Last Answer : Answer: Option A

An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Last Answer : Answer: Option C

For the manufacture of plywood, veneers are placed so that grains of adjacent veneers (A) Run at right angles (B) Parallel (C) Inclined at 45° (D) Inclined at 60°

Description : For the manufacture of plywood, veneers are placed so that grains of adjacent veneers (A) Run at right angles (B) Parallel (C) Inclined at 45° (D) Inclined at 60°

Last Answer : Answer: Option A

Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Description : Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Last Answer : [ D ] d

In a cantilever carrying a uniformly varying load starting from zero at the free end, the Bending moment diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the Bending moment diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Last Answer : (d) Follows a cubic law

In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Last Answer : (c) Follows a parabolic law

A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin 314t+45 deg)is examined with a line base settings of 5 msec/div, the number of cycles of signal displayed on the screen will be a) 0.5 cycles b) 2.5 cycles c) 5 cycles d) 10 cycles

Description : A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin 314t+45 deg)is examined with a line base settings of 5 msec/div, the number of cycles of signal displayed on the screen will be a) 0.5 cycles b) 2.5 cycles c) 5 cycles d) 10 cycles

Last Answer : Ans: 2.5 cycles

The locus of the end point of the resultant of the normal and tangential components of the stress on an inclined plane, is (A) Circle (B) Parabola (C) Ellipse (D) Straight line

Description : The locus of the end point of the resultant of the normal and tangential components of the stress  on an inclined plane, is  (A) Circle  (B) Parabola  (C) Ellipse  (D) Straight line 

Last Answer : (C) Ellipse 

On mollier chart ,free expansion or throttling process from High pressure to atmosphere is represented by • Horizontal straight line • Vertical straight line • Straight inclined line • Curved line

Description : On mollier chart ,free expansion or throttling process from High pressure to atmosphere is represented by • Horizontal straight line • Vertical straight line • Straight inclined line • Curved line

Last Answer : • Horizontal straight line

Y –axis in a CRO normally represents

Description : Y –axis in a CRO normally represents

Last Answer : Volt 

In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°

Last Answer : 180°

The function of input attenuators in measuring instruments, like VTVM and CRO, is to

Description : The function of input attenuators in measuring instruments, like VTVM and CRO, is to (a) Increase the input impedance (b) Attenuate the frequency range (c) Attenuate the input signal amplitude without altering the frequency contents (d) Attenuate the input impedance

Last Answer : The function of input attenuators in measuring instruments, like VTVM and CRO, is to Attenuate the input signal amplitude without altering the frequency contents

A piano tuner notices a standing Lissajous (pron: Liss-a-jew) curve on his oscilloscope. The tone being projected is: w) out of harmony x) sharp y) resonating z) flat

Description : A piano tuner notices a standing Lissajous (pron: Liss-a-jew) curve on his oscilloscope. The tone being projected is: w) out of harmony x) sharp y) resonating z) flat

Last Answer : ANSWER: Y -- RESONATING

Draw the graph of the equation represented by a straight Line which is parallel to the X-axis and at a distance 3 units below it. -Maths 9th

Description : Draw the graph of the equation represented by a straight Line which is parallel to the X-axis and at a distance 3 units below it. -Maths 9th

Last Answer : Any straight line parallel to X-axis in negative direction of Y-axis is given by y = - k, where k is the distance of the line from the X-axis. Here, k = 3. Therefore, the equation of the line is y = -3. To ... , plot the points (1,-3), (2, -3) and (3, -3) and join them. This is the required graph.

Draw the graph of the equation represented by a straight Line which is parallel to the X-axis and at a distance 3 units below it. -Maths 9th

Description : Draw the graph of the equation represented by a straight Line which is parallel to the X-axis and at a distance 3 units below it. -Maths 9th

Last Answer : Any straight line parallel to X-axis in negative direction of Y-axis is given by y = - k, where k is the distance of the line from the X-axis. Here, k = 3. Therefore, the equation of the line is y = -3. To ... , plot the points (1,-3), (2, -3) and (3, -3) and join them. This is the required graph.

Draw the graph of the equation represented by the straight line which is parallel to the x-axis and 3 units above it. -Maths 9th

Description : Draw the graph of the equation represented by the straight line which is parallel to the x-axis and 3 units above it. -Maths 9th

Last Answer : Solution :- Any straight line parallel to x-axis is given by y = a, where a is the distance of the line from the x-axis. Here a = 3. Therefore the equation of the line is y = 3. To draw the graph of this equation plot the points (0, 3) and (3, 3) and join them.

When a graph is plotted between log x/m and log p, it is straight line with an angle `45^(@)` and intercept 0.3010 on y - axis. If initial pressure is

Description : When a graph is plotted between log x/m and log p, it is straight line with an angle `45^(@)` and intercept 0.3010 on y - axis. If initial pressure is

Last Answer : When a graph is plotted between log x/m and log p, it is straight line with an angle `45 ... adsorbent : (Report your answer after multiplying by 10)

The graph of the polynomial p(x) = 3x – 2 is a straight line which intersects the x-axis at exactly one point namely (a) (−2/3, 0) (b) (0, −2/3) (c) (2/3, 0) (d)( 2/3, −2/3)

Description : The graph of the polynomial p(x) = 3x – 2 is a straight line which intersects the x-axis at exactly one point namely (a) (−2/3, 0) (b) (0, −2/3) (c) (2/3, 0) (d)( 2/3, −2/3)

Last Answer : (c) (2/3, 0)

Long run supply curve of a decreasing cost industry is (a) Downward sloping curve ; (b) Upward sloping curve; (c) Straight line parallel to X axis ; (d) Straight line parallel to y axis

Description : Long run supply curve of a decreasing cost industry is (a) Downward sloping curve ; (b) Upward sloping curve; (c) Straight line parallel to X axis ; (d) Straight line parallel to y axis

Last Answer : (a) Downward sloping curve ;

The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Description : The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Last Answer : b) Grid

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

The lamina dura is seen on periapical radiographs as:CHECK A. Usual radiolucency between tooth root and surrounding bone as a thin white line. B. Cribriform plate of bone making the tooth socket C. Dense crestal bone consistent with a healthy periodontal status D. Pattern of radiopaque lines in supporting alveolar bone

Description : The lamina dura is seen on periapical radiographs as:CHECK A. Usual radiolucency between tooth root and surrounding bone as a thin white line. B. Cribriform plate of bone making the ... bone consistent with a healthy periodontal status D. Pattern of radiopaque lines in supporting alveolar bone

Last Answer : B. Cribriform plate of bone making the tooth socket

In horizontal angles, the error due to imperfect levelling of the plate bubble is (A) Large when sights are nearly level (B) Large for long sights (C) Less for steeply inclined sights (D) Large for steeply inclined sights

Description : In horizontal angles, the error due to imperfect levelling of the plate bubble is (A) Large when sights are nearly level (B) Large for long sights (C) Less for steeply inclined sights (D) Large for steeply inclined sights

Last Answer : (D) Large for steeply inclined sights

A metering mechanism that does not required cut-off device is: A. Inclined plate B. Vertical plate C. Horizontal plate D. All are correct

Description : A metering mechanism that does not required cut-off device is: A. Inclined plate B. Vertical plate C. Horizontal plate D. All are correct

Last Answer :  All are correct

Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Last Answer : (a) Inclined plate metering

Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Last Answer : (d) Inclined plate metering mechanism

A boy sitting in a rail road car throws a ball straight up into the air. The ball will fall back into his hands when the rail road car is a.moving at constant velocity b.accelerating forward while going around a curve of radius equal to the maximum height attained by the ball c.107 dynes d.accelerating forwardA block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height e.decelerating

Description : A boy sitting in a rail road car throws a ball straight up into the air. The ball will fall back into his hands when the rail road car is a.moving at constant velocity b.accelerating ... inclined plane, while another identical block B is released for free fall from the same height e.decelerating

Last Answer : a. moving at constant velocity

Straight, parallel and widely spaced contours represent (A) A steep surface (B) A flat surface (C) An inclined plane surface (D) Curved surface

Description : Straight, parallel and widely spaced contours represent (A) A steep surface (B) A flat surface (C) An inclined plane surface (D) Curved surface

Last Answer : (C) An inclined plane surface

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

The dew point temperature lines on psychrometric charts are straight inclined sloping downwards to the right. When relative humidity of moist air is 100%, then (A) Wet bulb temperature=dry bulb temperature (B) Wet bulb temperature=dew point temperature (C) Saturation temperature=dew point temperature (D) All 'a', 'b' & 'c

Description : The dew point temperature lines on psychrometric charts are straight inclined sloping downwards to the right. When relative humidity of moist air is 100%, then (A) Wet bulb temperature=dry bulb temperature (B) ... temperature (C) Saturation temperature=dew point temperature (D) All 'a', 'b' & 'c

Last Answer : Option D