A CRO screen has ten divisions on the horizontal scale. If a voltage signal 5 sin 314t+45 deg)is examined with a line base settings of 5 msec/div, the number of cycles of signal displayed on the screen will be a) 0.5 cycles b) 2.5 cycles c) 5 cycles d) 10 cycles

A CRO screen has ten divisions on the horizontal scale. If a voltage
signal 5 sin 314t+45 deg)is examined with a line base settings of 5
msec/div, the number of cycles of signal displayed on the screen will be
a) 0.5 cycles
b) 2.5 cycles
c) 5 cycles
d) 10 cycles
by

1 Answer

Answer :

Ans: 2.5 cycles
by

Related questions

The time base signal in Cathode Ray Oscilloscope (CRO) is

Description : The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

Last Answer : 2 Saw tooth 

In CRO the time base signal is applied to:

Last Answer : In CRO the time base signal is applied to: X-plates

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Description : What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Last Answer : A. 256 msec

The number of cycles per second occurring in AC voltage is known as the _____________. A. phase angle B. frequency C. wave form D. half mode

Description : The number of cycles per second occurring in AC voltage is known as the _____________. A. phase angle B. frequency C. wave form D. half mode

Last Answer : Answer: B

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is

Description : The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°) 

Last Answer : The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is 2 sin ωt 

In ceiling fan the angle between auxiliary winding a main winding is a) 0 deg b) 90 deg c) 180 deg d) 360 deg

Description : In ceiling fan the angle between auxiliary winding a main winding is a) 0 deg b) 90 deg c) 180 deg d) 360 deg

Last Answer : Ans: 90 deg

The cycles per second developed by the alternator aboard your vessel is determined by _____________. A. the speed of the engine driving the alternator B. the resistance applied to the field rheostat C. the synchronous speed of induction D. the adjustments made to the voltage regulator

Description : The cycles per second developed by the alternator aboard your vessel is determined by _____________. A. the speed of the engine driving the alternator B. the resistance applied to the field rheostat C. the synchronous speed of induction D. the adjustments made to the voltage regulator

Last Answer : Answer: A

Draw and describe horizontal deflection system in CRO

Description : Draw and describe horizontal deflection system in CRO 

Last Answer : Block Diagram: Explanation: Input from vertical amplifier is given to Horizontal system. Trigger circuit: a. A trigger circuit is used to convert the incoming signal into trigger ... : Horizontal amplifier amplifies the signal & passes the signal to horizontal plates of CRT. 

Horizontal deflection plates of CRO are placed generally

Description : Horizontal deflection plates of CRO are placed generally   (a) Horizontal (b) Vertical (c) Diagonal (d) (a) or (b)  

Last Answer : Horizontal

The division of the kilowatt load between two AC generators operating in parallel is controlled by the settings and characteristics of the _____________. A. voltage regulators B. field rheostats C. reverse power relays D. prime mover governors

Description : The division of the kilowatt load between two AC generators operating in parallel is controlled by the settings and characteristics of the _____________. A. voltage regulators B. field rheostats C. reverse power relays D. prime mover governors

Last Answer : Answer: D

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave

Description : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen ... channels are the same, the amplitude (pp) and period of the unknown signal are respectively.

Last Answer : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen is ... are the same, the amplitude (pp) and period of the unknown signal are respectively. 7.5 V, 2ms

V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the circuit a) R=30 ohm, L=30 mH b) R=30 ohm, C=33.3 micro farads c) R=40 ohm, L=30 mH d) R=40 ohm, L=33.3 micro farads

Description : V=100Sin (1000t+46 deg), I=2Sin (1000t+80 deg) what are the elements in the circuit a) R=30 ohm, L=30 mH b) R=30 ohm, C=33.3 micro farads c) R=40 ohm, L=30 mH d) R=40 ohm, L=33.3 micro farads

Last Answer : Ans: R=40 ohm, L=33.3 micro farads

Suppose that the time to do a null remote procedure call (RPC) (i.e, 0 data bytes) is 1.0 msec, with an additional 1.5 msec for every 1K of data. How long does it take to read 32 K from the file server as 32 1K RPCs? (A) 49 msec (B) 80 msec (C) 48 msec (D) 100 msec

Description : Suppose that the time to do a null remote procedure call (RPC) (i.e, 0 data bytes) is 1.0 msec, with an additional 1.5 msec for every 1K of data. How long does it take to read 32 K from the file server as 32 1K RPCs? (A) 49 msec (B) 80 msec (C) 48 msec (D) 100 msec

Last Answer : (B) 80 msec

Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Description : Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Last Answer : Answer: C

When paralleling two AC generators, the frequency (cycles) of the incoming generator, just prior to closing the circuit breaker, should be _____________. A. slightly less than the frequency of the generator on the line B. the same as the frequency of the generator on the line C. slightly more than the frequency of the generator on the line D. all of the above

Description : When paralleling two AC generators, the frequency (cycles) of the incoming generator, just prior to closing the circuit breaker, should be _____________. A. slightly less than the frequency of the generator on ... C. slightly more than the frequency of the generator on the line D. all of the above

Last Answer : Answer: C

Statistics , Problems with Two Projectors ? From the top of a 100 meter high tower an object is thrown at a 30 ° angle with a horizontal speed of 50 ms . At the same time another object from the base of the tower was thrown at an angle of 45 সাথে with the same velocity horizontally . At what time and at what height will the two objects meet ?

Description : Statistics , Problems with Two Projectors ? From the top of a 100 meter high tower an object is thrown at a 30 ° angle with a horizontal speed of 50 ms . At the same time another object from ... সাথে with the same velocity horizontally . At what time and at what height will the two objects meet ?

Last Answer : answer:

The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division on passing a current of `4xx 10 ^(-4

Description : The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division on passing a current of `4xx 10 ^(-4

Last Answer : The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division ... is A. 150 B. 170 C. 110 D. 220

When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be _______ EL-0018 A. 88.95 milliamps B. 103.45 milliamps C. 11.24 milliamps D. 0.91 amps

Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be _______ EL-0018 A. 88.95 milliamps B. 103.45 milliamps C. 11.24 milliamps D. 0.91 amps

Last Answer : Answer: C

A 8-Mbps tokenring has atoken holding timer value of 10 msec. What is the longest frame (assumeheader bits are negligible) that canbe sent on this ring? A. 8000 B frame B. 80,000 B frame C. 8 x 105 bit frame D. 10,000 B frame

Description : A 8-Mbps tokenring has atoken holding timer value of 10 msec. What is the longest frame (assumeheader bits are negligible) that canbe sent on this ring? A. 8000 B frame B. 80,000 B frame C. 8 x 105 bit frame D. 10,000 B frame

Last Answer : 10,000 B frame

A disk drive has 100 cylinders, numbered 0 to 99. Disk requests come to the disk driver for cyclinders 12, 26, 24, 4, 42, 8 and 50 in that order. The driver is currently serving a request at cyclinder 24. A seek takes 6 msec per cyclinder moved. How much seek time is needed for shortest seek time first (SSTF) algorithm? (A) 0.984 sec (B) 0.396 sec (C) 0.738 sec (D) 0.42 sec

Description : A disk drive has 100 cylinders, numbered 0 to 99. Disk requests come to the disk driver for cyclinders 12, 26, 24, 4, 42, 8 and 50 in that order. The driver is currently serving a request at cyclinder 24. A seek takes ... (SSTF) algorithm? (A) 0.984 sec (B) 0.396 sec (C) 0.738 sec (D) 0.42 sec

Last Answer : C

A dynamic RAM has refresh cycle of 32 times per msec. Each refresh operation requires 100 nsec and a memory cycle requires 250 nsec. What percentage of memory’s total operating time is required for refreshes? (A) 0.64 (B) 0.96 (C) 2.00 (D) 0.32

Description : A dynamic RAM has refresh cycle of 32 times per msec. Each refresh operation requires 100 nsec and a memory cycle requires 250 nsec. What percentage of memory’s total operating time is required for refreshes? (A) 0.64 (B) 0.96 (C) 2.00 (D) 0.32

Last Answer : Answer: D Explanation: in 1ms : refresh = 32 times Memory cycle = 1ms/250ns = 106ns/250ns = 4000 times Therefore, % of refresh time = (32 x 100ns)/(4000 x 250ns) = 3200ns/1000000 x 100% = 0.32%

The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Description : The ___________ of a CRO controls the brightness of the spot formed on the screen a) Filament b) Grid c) Deflection plates d) Cathode

Last Answer : b) Grid

The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a

Description : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with its major ... frequencies very close but not equal D) There is a constant but small phase difference between the signals

Last Answer : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with ... following inference can be made from this The signals are sinusoidal with their frequencies very close but not equal 

The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4.

Description : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be :  (A) 270° (B) 210° (C) 180° (D) 300°

Last Answer : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be : 210°

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

Lissajous pattern obtained on a CRO screen is a circle. Frequency of two signals are

Description : Lissajous pattern obtained on a CRO screen is a circle. Frequency of two signals are   (a) Equal (b) Unequal (c) Zero (d) Infinity 

Last Answer : a

It cannot be determined from Gauss law, whereas the remaining options can be computed from Gauss law. 10. Gauss law for magnetic fields is given by a) Div(E) = 0 b) Div(B) = 0 c) Div(H) = 0 d) Div(D) = 0

Description : It cannot be determined from Gauss law, whereas the remaining options can be computed from Gauss law. 10. Gauss law for magnetic fields is given by a) Div(E) = 0 b) Div(B) = 0 c) Div(H) = 0 d) Div(D) = 0

Last Answer : b) Div(B) = 0

Which of the following true statement about CRO? A. Decreased ROI B. Improve user base C. Increased acquisition cost D. All of the above

Description : Which of the following true statement about CRO? A. Decreased ROI B. Improve user base C. Increased acquisition cost D. All of the above

Last Answer : B. Improve user base

The output waveform produced due to time base generator in a CRO is a) saw tooth b) sinusoidal c) linear d) helical

Description : The output waveform produced due to time base generator in a CRO is a) saw tooth b) sinusoidal c) linear d) helical

Last Answer : a) saw tooth

(i) Social ……………. involves the formation of horizontal social divisions. (stratification / differentiation / hierarchy)

Description : (i) Social ……………. involves the formation of horizontal social divisions. (stratification / differentiation / hierarchy)

Last Answer : Choose the correct alternative and complete the statements : (i) Social . involves the ... social stratification. (closed / open / equal)

The least count of a Vernier scale is (A) Sum of the smallest divisions of main and Vernier scales (B) Value of one division of the primary scale divided by total number of divisions of Vernier scale (C) Value of one division of Vernier scale divided by total number of divisions of primary scale (D) None of these

Description : The least count of a Vernier scale is  (A) Sum of the smallest divisions of main and Vernier scales  (B) Value of one division of the primary scale divided by total number of divisions ... division of Vernier scale divided by total number of divisions of primary scale  (D) None of these 

Last Answer : (B) Value of one division of the primary scale divided by total number of divisions of Vernier  scale 

What is the rectangle in the world defining the region that is to be displayed? a.World co-ordinate system b.Screen co-ordinate system c.World window d.Interface window

Description : What is the rectangle in the world defining the region that is to be displayed? a.World co-ordinate system b.Screen co-ordinate system c.World window d.Interface window

Last Answer : c.World window

What is the name of the space in which the image is displayed? a.World co-ordinate system b.Screen co-ordinate system c.World window d.Interface window

Description : What is the name of the space in which the image is displayed? a.World co-ordinate system b.Screen co-ordinate system c.World window d.Interface window

Last Answer : b.Screen co-ordinate system

Explain How can you find if an element in displayed on the screen?

Description : Explain How can you find if an element in displayed on the screen?

Last Answer : WebDriver facilitates the user with the following methods to check the visibility of the web elements. These web elements can be buttons, drop boxes, checkboxes, radio buttons, labels etc. 1.isDisplayed ... (); isEnabled(): boolean searchIconEnabled = driver.findElement(By.id( gbqfb )).isEnabled();

When an operating system prompt (A>) is displayed on the screen, what do you enter from the keyboard to load an application program?

Description : When an operating system prompt (A>) is displayed on the screen, what do you enter from the keyboard to load an application program?

Last Answer : The program name.

A certain population of ALOHA users manages to generate 70 request/sec. If the time is slotted in units of 50 msec, then channel load would be a. 4.25 b. 3.5 c. 350 d. 450

Description : A certain population of ALOHA users manages to generate 70 request/sec. If the time is slotted in units of 50 msec, then channel load would be a. 4.25 b. 3.5 c. 350 d. 450

Last Answer : b. 3.5

Explain the measurement of voltage and frequency using CRO.

Description : Explain the measurement of voltage and frequency using CRO.

Last Answer : Voltage Measurement: CRO displays the voltage signal as a function of time on its screen. The amplitude of that voltage signal is constant, but we can vary the number of divisions that cover the voltage ... /division nv is the number of divisions that cover the signal in vertical direction.

A moving coil galvanometer has 150 equal divisions. Its current sensitivity is 10-divisions per milliampere and voltage sensitivity is 2 divisions per

Description : A moving coil galvanometer has 150 equal divisions. Its current sensitivity is 10-divisions per milliampere and voltage sensitivity is 2 divisions per

Last Answer : A moving coil galvanometer has 150 equal divisions. Its current sensitivity is 10-divisions per milliampere and voltage ... `10^(3)` D. `10^(5)`

A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Description : A circuit which develops voltage across the horizontal deflection plates is known as a) Time base generator b) Electron gun c) Thermionic diode d) Zener diode

Last Answer : a) Time base generator

The main scale of a vernier callipers has n divisions/cm. n divisions of the vernier scale coincide with (n – 1) divisions of main scale.

Description : The main scale of a vernier callipers has n divisions/cm. n divisions of the vernier scale coincide with (n – 1) divisions of main scale.

Last Answer : The main scale of a vernier callipers has n divisions/cm. n divisions of the vernier scale coincide with (n - 1) ... n}\) (D) \(\frac{1}{n^2}\)

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'B'? EL-0047 A. 1.45 ohms B. 7.2 ohms C. 37 ohms D. 70 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'B'? EL-0047 A. 1.45 ohms B. 7.2 ohms C. 37 ohms D. 70 ohms

Last Answer : Answer: D

Stretch reflex: a. is a monosynaptic reflex with a response time of 1 msec b. originates in the muscle spindle which sends off impulses in type Ia nerve fibres c. is intensified by impulses in the gamma efferent fibres d. all above

Description : Stretch reflex: a. is a monosynaptic reflex with a response time of 1 msec b. originates in the muscle spindle which sends off impulses in type Ia nerve fibres c. is intensified by impulses in the gamma efferent fibres d. all above

Last Answer : all above

In a time multiplexed space switching system, one speech sample appears every (A) 125 micro sec (B) 20 msec (C) 125 msec (D) 1 sec

Description : In a time multiplexed space switching system, one speech sample appears every (A) 125 micro sec (B) 20 msec (C) 125 msec (D) 1 sec

Last Answer : (A) 125 micro sec

The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Description : The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Last Answer : Ans: C The access time of ROM using bipolar transistors is about 1 µ sec.

Consider a disk with 16384 bytes per track having a rotation time of 16 msec and average seek time of 40 msec. What is the time in msec to read a block of 1024 bytes from this disk? (A) 57 msec (B) 49 msec (C) 48 msec (D) 17 msec

Description : Consider a disk with 16384 bytes per track having a rotation time of 16 msec and average seek time of 40 msec. What is the time in msec to read a block of 1024 bytes from this disk? (A) 57 msec (B) 49 msec (C) 48 msec (D) 17 msec

Last Answer : Answer: B

A dot matrix printer takes 3 msec to point a character, and 1 msec for a space between two consecutive

Description : A dot matrix printer takes 3 msec to point a character, and 1 msec for a space between two consecutive characters. If it prints 100 characters per line, its printing speed specifications in characters per second (cps) and time ... 2500 cps and 0.04 sec (c) 250 cps and 40 msec (d) 250 cps and 0.4 sec

Last Answer : A dot matrix printer takes 3 msec to point a character, and 1 msec for a space between two consecutive characters. If it prints 100 characters per line, its printing speed specifications in characters per second (cps) and time ... cps and 0.04 sec (c) 250 cps and 40 msec (d) 250 cps and 0.4 sec

Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Description : Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Last Answer : Ans: 10 W*

A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of + or - 2%. A meter reading of 10 milliamps would indicate a line current of between _____________. A. 9.8 and 10.0 milliamperes B. 9.8 and 10.2 milliamperes C. 8.0 and 12.0 milliamperes D. 8.0 and 10.0 milliamperes

Description : A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of + or - 2%. A meter reading of 10 milliamps would indicate a line current of between _____________. A. 9.8 ... 9.8 and 10.2 milliamperes C. 8.0 and 12.0 milliamperes D. 8.0 and 10.0 milliamperes

Last Answer : Answer: B