Description : In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane
Last Answer : (D) Equally on each fibre along horizontal plane (D) Equally on each fibre along horizontal plane
Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section
Last Answer : (B) Top fibre
Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16
Last Answer : Answer: Option D
Description : When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these
Last Answer : (b) Bottom fibre
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable ... to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress
Last Answer : Answer: Option C
Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°
Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5
Last Answer : (B) L/3
Description : A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward
Last Answer : (d) Parabolic, with convexity downward
Description : A 8 metre long simply supported rectangular beam which carries a distributed load 45 kg/m. experiences a maximum fibre stress 160 kg/cm2 . If the moment of inertia of the beam is 640 cm4 , the overall depth of the beam is (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm
Last Answer : (A) 10 cm
Description : In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero
Last Answer : (a) Compressive, tensile
Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope ... arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E
Last Answer : (D) 200/E
Description : Distribution of shear intensity over a rectangular section of a beam, follows: (A) A circular curve (B) A straight line (C) A parabolic curve (D) An elliptical curve
Description : The maximum shear stress (qmax) in a rectangular beam is (A) 1.25 times the average (B) 1.50 times the average (C) 1.75 times the average (D) 2.0 times the average
Last Answer : Answer: Option B
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : The maximum shear stress in rectangular beam is _____________________times of average shear stress. (a) 1.15 (b) 1.25 (c) 1.50 (d) 1.75
Last Answer : (c) 1.50
Description : A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange
Last Answer : c. neutral axis of the section
Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis
Description : 0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre (B) In the standard rolled channels, the shear centre ... horizontal plane and away from the C.G., outside of the leg projection (D) All the above
Last Answer : (D) All the above
Description : The maximum shear stress occurs on the filament which makes an angle with the horizontal plane equal to (A) 30° (B) 45° (C) 60° (D) 90
Last Answer : (B) 45°
Description : In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on (A) Horizontal plane only (B) Vertical plane only (C) Both horizontal and vertical planes (D) All planes except horizontal and vertical planes
Last Answer : (D) All planes except horizontal and vertical planes
Description : An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis
Last Answer : Upward deflection
Description : Regarding the National Flag choose the correct options from the following statements i) It has a horizontal strip of three colours including deep saffron at the top, white in the middle, and dark green at the bottom. ii) The ratio of the flag width to its length is 2:3 -Science
Last Answer : Both i and ii The National Flag of India has a horizontal strip of three colours including deep saffron (Kesaria) at the top, white in the middle, and dark green at the bottom. The ratio of the flag width to its length is 2:3.
Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2
Last Answer : b. 33.33 N/mm2
Description : State the position of maximum shear stress and bending stress in S/S rectangular beam section carrying udl.
Last Answer : i. Maximum shear stress developed at the neutral axis of the rectangular section at support of simply supported beam. ii. Maximum bending stress developed at the top and bottom fibre of the rectangular section at mid span of simply supported beam.
Description : The discharge through a large rectangular orifice is given by (where H1 = Height of the liquid above the top of the orifice, H2 = Height of the liquid above the bottom of the orifice, b = Breadth of the orifice, and Cd = Coefficient of ... H1 3/2) (D) Q = (2/3) Cd b (2g) (H2 2 - H1 2 )
Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular
Last Answer : b) Transverse loads and couples
Description : In a colar beam roof (A) There is no horizontal tie beam (B) There is a horizontal tie at the feet of rafters only (C) There is a horizontal tie at almost the middle of rafters only (D) There are two horizontal ties, one at the feet and other at the middle of the rafters
Description : Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom ... (C) Construction joints in beams and slabs are provided within middle third (D) All the above
Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis
Last Answer : (D) Bending stress is same at every section along its longitudinal axis
Description : A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS
Last Answer : (A) 3S/bh
Description : If longitudinally spanning stairs are casted along with their landings, the maximum bending moment per metre width, is taken as (A) wl²/4 (B) wl²/8 (C) wl²/10 (D) wl²/12
Description : Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh
Description : For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola
Last Answer : (c) Line inclined to x-axis
Description : 7-For any part of the beam, between two concentrated load Shear force diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola
Last Answer : Na
Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm
Last Answer : (D) 8 cm
Description : The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these
Last Answer : (A) Pass through the centroid of the section
Description : The effective depth of a T-beam is the distance between the (a) Centre of the flange and the top of the tensile reinforcement (b) Top of the flange and the centre of the tensile ... centre of the tensile reinforcement (d) Centre of the flange and the bottom centre of the tensile reinforcement
Last Answer : (b) Top of the flange and the centre of the tensile reinforcement
Description : A young woman owns two horses, a plane, a gun, a tape with many markings, and a machine with sharp teeth which she uses almost every day. She does not use any of these for transportation or ... does this young woman do for a living, and why does she need this strange assortment of objects? -Riddles
Last Answer : The young woman is a carpenter. She uses her two sawhorses, her carpenter’s plane, her nail gun, her tape measure, and her circular saw almost every day as she works to earn a living.
Description : Through a point in a loaded soil mass, there exists typical planes mutually orthogonal on which the stress is wholly normal and no shear stress acts, if is (A) 1 (B) 2 (C) 3 (D) 4
Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force
Description : A three hinged arch is loaded with an isolated load 1000 kg at a horizontal distance of 2.5 m from the crown, 1 m above the level of hinges at the supports 10 metres apart. The horizontal thrust is (A) 1250 kg (B) 125 kg (C) 750 kg (D) 2500 kg
Last Answer : (A) 1250 kg
Description : Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of equal area (D) All the above
Description : In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5
Last Answer : (D) L/5
Description : In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : The maximum harbour depth below lowest low water is generally equal to (i) Loaded draft +1.2 m when bottom is rock (ii) Loaded draft +1.8 m when bottom is soft (iii) Loaded draft +1.2 m when bottom is ... ) and (iii) are correct (C) (ii) and (iv) are correct (D) (iii) and (iv) are correct
Last Answer : (D) (iii) and (iv) are correct