Description : Density of water is maximum at (A) 0° C (B) 0° K (C) 4° C
Last Answer : Answer: Option C
Description : The angle of internal friction of clays, is usually (A) 0° to 5° (B) 5° to 20° (C) 20° to 30° (D) 30° to 45
Last Answer : Answer: Option B
Description : The temperature at which both the Fahrenheit and Centigrade scales have the same value is – (1) -60° (2) -40° (3) -20° (4) 0°
Last Answer : (2) -40° Explanation: The temperature when both the Celsius and Fahrenheit scales are the same is -40 degrees.
Description : What is the orbit inclination of geostationary satellites? A. 0° B. 10° C. 20° D. 30°
Last Answer : A. 0°
Description : (4) water and petrol are immiscible with each other and petrol which forms the upper layer continues to burn Explanation: Water is not effective in extinguishing a fire caused by petrol because water and ... . Water cannot generally be used to extinguish a gasoline fire, unless used in a fine mist.
Last Answer : "All the four quantum numbers of two electrons in an atom are not the same." It is the law of (1) Hund’s (2) Exclusion Principle of Pauli (3) Uncertainty Principle of Giesenberg (4) Avogadro’s law
Description : Density of Water is-----? A. 897 kg/m3 B. 997 kg/m3 (Answer) C. 1000 kg/m3 D. 1025 kg/m3
Last Answer : B. 997 kg/m3 (Answer)
Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these
Last Answer : (A) 4.4 KPa
Description : Water has maximum density at------? A. 0°C B. 4°C (Answer) C. 4° K D. 4.8°C
Last Answer : B. 4°C (Answer)
Description : Bulk density of pulverised coal may be about __________ kg/m3 . (A) 100 (B) 500 (C) 1000 (D) 1500
Last Answer : (B) 500
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : . An irreversible aqueous phase reaction, A + B → P, is carried out in an adiabatic mixed flow reactor. A feed containing 4kmole/m3 of each A and B enters the reactor at 8m3 /hr. If the temperature of ... be assumed to be independent of temperature and composition. (A) 190 (B) 290 (C) 390 (D) 490
Last Answer : (B) 290
Description : A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k ) a. 543680 N/m2 b. 543.68 kPa (gauge) c. Both a & b d. None of the above
Last Answer : Both a & b
Description : 19. The density of a liquid in kg/m3 is numerically equal to its specific gravity. A) True B) False
Last Answer : A
Description : The mass of 2.5 m3 of a certain liquid is 2 tonnes. Its mass density is (A) 200 kg/m3 (B) 400 kg/m3 (C) 600 kg/m3 (D) 800 kg/m
Last Answer : Answer: Option D
Description : The bulk density of aggregates , is (a) kN/m3 (b) Kg/1tr (c) g/cm3 (d) All the above.
Last Answer : (b) Kg/1tr
Description : What is the specific weight of water at standard condition? (Formula: γ = ρg / k) a. 1000 kgm/m3 b. 9.8066 m/s2 c. 1000 kgf/m3 d. None of the above
Last Answer : 1000 kgf/m3
Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000
Last Answer : (C) 600
Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ
Last Answer : (A) 3.6 W.D.V.ρ
Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ
Last Answer : (A) 3.6 AVS.ρ
Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ
Last Answer : (A) 3.6 V.W.Dr.ρ
Description : The density of Air is-------? A. 0.225 kg/m3 B. 1.025 kg/m3 C. 1.225 kg/m3 (Answer) D. 1.425 kg/m3
Last Answer : C. 1.225 kg/m3 (Answer)
Description : A bed consists of particles of density 2000 kg/m3 . If the height of the bed is 1.5 metres and its porosity 0.6, the pressure drop required to fluidise the bed by air is (A) 25.61 kPa (B) 11.77 kPa (C) 14.86 kPa (D) 21.13 kPa
Last Answer : (B) 11.77 kPa
Description : A gas (density = 1.5 kg/m3 , viscosity = 2 10 -5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The ... flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m
Last Answer : (B) 12600 Pa/m
Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000
Last Answer : 21600
Description : Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into ... °C b. 8.9°C c. 9.9°C d. 10.9°C formula: ΔQ = m c ΔT
Last Answer : 7.9 °C
Description : What is the unit of relative density? (1) kg/m (2) kg/m2 (3) kg/m3 (4) It has no unit
Last Answer : It has no unit
Description : For clear distinct vision, images of obstructions should fall on the retina with a cone of (A) 2° (B) 3° (C) 4° (D) 5°
Description : If the radius of a main curve is 300 m and length of the transition curve is 100 m, the angle with tangent to locate the junction point, is (A) 1° 11' (B) 2° 11' (C) 3° 11' (D) 4° 11'
Description : If the ruling gradient is 1 in 150 on a particular section of a broad gauge track, the allowable ruling gradient on a 4° curve in the track will be : (a) 0.51% (b) 0.53% (c) 0.61% (d) 0.67%
Last Answer : (a) 0.51%
Description : The value of mass density in kg-sec-V- (A) 1 (B) 1000 (C) 100 (D) 101.9
Description : A portion of an embankment having a uniform up-gradient 1 in 500 is circular with radius 1000 m of the centre line. It subtends 180° at the centre. If the height of the bank is 1 m at the lower end, and side slopes 2 ... earth work involved. (A) 26,000 m3 (B) 26,500 m3 (C) 27,000 m3 (D) 27,500 m
Last Answer : (D) 27,500 m3
Description : The weight of reinforced concrete, is generally taken as (A) 2200 kg/m3 (B) 2300 kg/m3 (C) 2400 kg/m3 (D) 2500 kg/m
Description : The live load to be considered for an accessible roof, is (A) Nil (B) 75 kg/m3 (C) 150 kg/m2 (D) 200 kg/cm
Description : An odd shaped body weighing 7.5 kg and occupying 0.01 m3 volume will be completely submerged in a fluid having specific gravity of (A) 1 (B) 1.2 (C) 0.8 (D) 0.75
Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)
Description : For melting one tonne of cast iron (A) 700 m3 air is required (B) 20 kg limestone is required (C) One quintal coke is required (D) All the above
Description : The weight of 1 m3 of brick earth, is about (A) 1200 kg (B) 1500 kg (C) 1800 kg (D) 2000 kg
Description : If is the angle of repose of soil of weight w kg/m3 , the horizontal pressure p at a depth of h metres per metre length of wall, is (A) wh × [(1 - sin )/(1 + )] (B) (wh/2) × [(1 - sin )/(1 + )] (C) wh - sin )/(1 + )] (D) wh )/(1 - )
Last Answer : Answer: Option A
Description : The weight of reinforced concrete is generally take as (a) 2300 kg/m3 (b) 2400 kg/m3 (c) 2500kg/m3 (d) 2800kg/m3
Last Answer : (d) 2800kg/m3
Description : According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3
Last Answer : [ B ] 0.4 kg/m3
Description : According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3
Last Answer : [ C ] 450 kg/m3
Description : According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3
Last Answer : [ B ] 300 kg/m3
Description : A masonry dam (density = 20,000 N/m3 ) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be (A) 75 N/m2 (B) 750 N/m2 (C) 7500 N/m2 (D) 75000 N/m
Last Answer : (C) 7500 N/m
Description : A soil has a bulk density of 22 kN/m3 and water content 10 %. The dry density of soil is (A) 18.6 kN/m3 (B) 20.0 kN/m3 (C) 22.0 kN/m3 (D) 23.2 kN/m3
Last Answer : (B) 20.0 kN/m3
Description : If the cohesive force (c), is 1.5 t/m2 , the density ) of the soil is 2.0 t/m3 , factor of safety (F) is 1.5 and stability factor (Sn) is 0.05, the safe height of a slope, is (A) 5 metres (B) 8 metres (C) 10 metres (D) 12 metres
Last Answer : (C) 10 metres
Description : The whole circle bearing of a line is 290°. Its reduced bearing is (A) N 20° E (B) N 20° W (C) N 70° W (D) S 70° E
Last Answer : (C) N 70° W
Description : If whole circle bearing of a line is 120°, its reduced bearing is (A) S 20° E (B) S 60° E (C) N 120° E (D) N 60° E
Last Answer : (B) S 60° E