Description : Consumptive use of a crop during growth, is the amount of (A) Interception (B) Transpiration (C) Evaporation (D) All the above
Last Answer : Answer: Option D
Description : Interception losses are due to (i) Evaporation (ii) Transpiration (iii) Stream flow The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)
Last Answer : Answer: Option A
Description : The degree of aridness of a geographic region is generally defined as the ratio of precipitation to: w) condensation x) evaporation y) transpiration z) snowpack depth
Last Answer : ANSWER: X -- EVAPORATION
Description : Pick up the correct statement from the following: (A) Rain which is intercepted by buildings, vegetations and other objects, is generally known as rainfall interception (B) The difference between ... the interception rainfall, water reaches the ground and infiltration starts (D) All the above
Description : Consider the following statements: 1. Over the oceans there is more evaporation than precipitation. 2. On land it is more precipitation than evapo-transpiration. Which of these statements are correct? (a) Both 1 & 2 (b) Neither 1 nor 2 (c) 1 only (d) 2 only
Last Answer : (a) Both 1 & 2
Description : The rate of evaporation from reservoirs may be determined by (A) Pan-measurement method (B) Empirical formulae (C) Storage equation method (D) All the above
Description : Differentiate between Transpiration and Evaporation. -Biology
Last Answer : answer:
Description : Transpiration differs from evaporation in: (a) Rate of water loss (b) Transpiration is a physiological process while evaporation is physical process (c) Transpiration is physical process while evaporation is physiological process (d) Frequency of water loss
Last Answer : Ans. ((b))
Description : Pmcess of water exudation through hydathodes is known as: (a) Guttation (b) Transpiration (c) Evaporation (d) Bleeding
Last Answer : Ans. ((a))
Description : Excess amount of absorbed water by plants is liberated out by – (1) Evaporation (2) Osmosis (3) Diffusion (4) Transpiration
Last Answer : (4) Transpiration Explanation: Water vapour transpires constantly through pores (stomata) in the surface of plant's leaves.
Description : Mulches are mainly used to reduce a. Transpiration b. Evaporation c. Evapotranspiration d. All of above
Last Answer : All of above
Description : In freeze- drying, water is removed from the product by a. Evaporation b. Sublimation c. Transpiration d. None of these
Last Answer : b. Sublimation
Description : Maximum loss of water from the plants occurs due to a. Transpiration b. Evaporation c. Guttation d. Respiration
Last Answer : a. Transpiration
Description : The loss of water by plants in the form of vapor i called: a) evaporation b) transpiration c) evapotranspiration d) vaporization
Last Answer : ANSWER: C -- evapotranspiration
Description : Excess amount of absorbed water by plants is liberated out by : (1) Evaporation (2) Osmosis (3) Diffusion (4) Transpiration
Last Answer : Transpiration
Description : The initial basin recharge is equal to (A) Interception (B) Depression storage (C) Rain absorbed by the moisture deficiency (D) All the above
Description : The trap which is provided to disconnect the house drain from the street sewer is called (A) Master trap (B) Intercepting trap (C) Interception manhole (D) All the above
Last Answer : (D) All the above
Description : Common salt is generally not produced commonly by __________ method from brine. (A) Freeze drying (B) Electrolytic (C) Solar evaporation (D) Vacuum evaporation
Last Answer : (A) Freeze drying
Description : Common salt is produced from sea water in India generally by the __________ method. (A) Freeze drying (B) Solar evaporation (C) Electrolytic (D) None of these
Last Answer : B) Solar evaporation
Description : Water gets evaporated from water surfaces and land surfaces, get converted into water drops at lower temperatures, flows over ground surface and finally meets its source, i.e. lake, sea, etc. This ... Hydrological cycle (B) Water cycle (C) Evaporation and precipitation cycle (D) All the above
Description : For evaporation and measurement of settable solids, the apparatus used, is A. A jar B. A breaker C. A test tube D. An Imhoff cone
Last Answer : ANS: D
Description : Difference between accretion and interception -Biology
Description : Why is interception important in netball?
Last Answer : Feel Free to Answer
Description : The type of threats on the security of a computer system or network are …………………….. i) Interruption ii)Interception iii) Modification iv) Creation v)Fabrication a) i, ii, iii and iv only b) ii, iii, iv and v only c) i, ii, iii and v only d) All i, ii, iii, iv and v
Last Answer : c) i, ii, iii and v only
Description : _______ is designed to be usedin wirelessapplications in which stations must be ableto sharethe medium without interception by an eavesdropperand without beingsubject tojamming from a malicious intruder. A) Spread spectrum B) Multiplexing C) Modulation D) None of the above
Last Answer : Spread spectrum
Description : For the protection of power station buildings against direct strokes the requirements are (a) interception (b) interception and conduction (c) interception, conduction and dissipation (d) interception, conduction, dissipation and reflection (e) none of the above
Last Answer : (c) interception, conduction and dissipation
Description : The type of threats on the security of a computer system or network are …………………….. i) Interruption ii) Interception iii) Modification iv) Creation v) Fabrication A) i, ii, iii and iv only B) ii, iii, iv and v only C) i, ii, iii and v only D) All i, ii, iii, iv and v
Last Answer : C) i, ii, iii and v only
Description : Multiple effect evaporation is generally recommended, when the (A) Large scale evaporation of liquor is needed (B) Corrosive liquids are to be concentrated
Last Answer : (A) Large scale evaporation of liquor is needed
Description : Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward ... (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product
Last Answer : (A) Get economical temperature difference by using moderate pressure steam
Description : The outlet temperature of cooling water in a heat exchanger is generally not allowed to exceed above 50°C in industrial practice mainly to avoid (A) Its evaporation loss (B) Excessive corrosion (C) Uneconomic LMTD (D) Decrease in heat exchanger efficiency
Last Answer : (B) Excessive corrosion
Description : According to ISI method of measurement, the order of the sequence is (A) Length, breadth, height (B) Breadth, length, height (C) Height, length, breadth (D) None of these
Last Answer : (A) Length, breadth, height
Description : From the surface of reservoir, evaporation may be minimised by sprinkling (A) Spirit (B) Hydrochloric acid (C) Acetyl alcohol (D) Methane
Last Answer : (C) Acetyl alcohol
Description : Rain simulators are used for the determination of (A) Evaporation (B) Precipitation (C) Run off (D) Infiltration capacity
Description : For calculating the evaporation rate over a reservoir surface E = 0.771 (1.465 - 0.00732B) (0.44 - 0.007375 V) (pe - pa), the equation is given by (A) Roohwer's, formula in M.K.S. (B) Roohwer's formula in F.P.S. (C) Dalton's formula in F.P.S. (D) Dalton's formula in M.K.S
Description : Evaporation losses depend upon (A) Area of the water surface and depth of the water (B) Nature of precipitation and type of vegetation (C) Humidity and wind velocity (D) All the above
Description : Pick up the correct statement from the following: (A) Rivers, lakes, oceans and springs get water from the rains (B) Rain water is obtained by evaporation from rivers, lakes and oceans (C) Water remains in atmosphere as vapours (D) All the above
Description : The most suitable chemical which can be applied to the water surface for reducing evaporation is (A) Methyl alcohol (B) Ethyl alcohol (C) Cetyl alcohol (D) Butyl alcohol
Last Answer : Answer: Option C
Description : Curing (A) Reduces the shrinkage of concrete (B) Preserves the properties of concrete (C) Prevents the loss of water by evaporation (D) All of the above
Last Answer : (D) All of the above
Description : Joints in concrete structures, are provided (A) To reduce the tensile stresses likely to be developed due to evaporation of water (B) To minimise the change in the dimensions of the slab (C) To minimise the necessary cracking (D) All the above
Description : Concrete gains strength due to (A) Chemical reaction of cement with sand and coarse aggregates (B) Evaporation of water from concrete (C) Hydration of cement (D) All the above
Description : The object of curing is to (a) Prevent the loss of water by evaporation. (b) Reduce the shrinkage of concrete (c) Preserve the properties of concrete (d) All of these
Last Answer : (d) All of these
Description : Concrete gains strength due to [ A ] Chemical reaction of cement with sand and coarse aggregates [ B ] Evaporation of water from concrete [ C ] Hydration of cement [ D ] All the above
Last Answer : [ C ] Hydration of cement
Description : The distances AC and BC are measured from two fixed points A and B whose distance AB is known. The point C is plotted by intersection. This method is generally adopted in (A) Chain surveying (B) Traverse method of surveys (C) Triangulation (D) None of these
Last Answer : (A) Chain surveying
Description : The method generally preferred to for contouring an undulating area, is (A) Chain surveying (B) Plane table surveying (C) Tacheometrical surveying (D) Compass surveying
Last Answer : (C) Tacheometrical surveying
Description : To orient a plane table at a point with two inaccessible points, the method generally adopted, is (A) Intersection (B) Resection (C) Radiation (D) Two point problem
Last Answer : (D) Two point problem
Description : Auger boring (A) Is the most primitive method for making a hole in the ground (B) Is generally employed in cohesive and other self soils above water table (C) Is most economical upto a depth of 5 metres (D) All the above
Description : Select incorrect statement from the following. In the Virtual work method, it is generally assumed that [ A ] Elastic deformations in the slab are negligible [ B ] Plastic deformations in the slab are negligible [ C ] Plastic deformations takes place at the yield lines [ D ] Both (a) and (b)
Last Answer : [ B ] Plastic deformations in the slab are negligible
Description : What is the difference between transpiration and guttation? -Biology
Last Answer : Transpiration and guttation are the two important process of removal of excess water from the plants. However, the two processes are different from each other. Transpiration is the removal of water ... loss of water from the plants. These were a few difference between transpiration and guttation.
Description : Differentiate between Guttation and Transpiration. -Biology