A hydraulic jump in a control meter will be formed above the control, if its original (A) Depth is more than critical depth (B) Depth is less than the critical depth (C) Depth is equal to critical depth (D) None of these

A hydraulic jump in a control meter will be formed above the control, if its original
(A) Depth is more than critical depth
(B) Depth is less than the critical depth
(C) Depth is equal to critical depth
(D) None of these
by

1 Answer

Answer :

Answer: Option B
by

Related questions

The critical depth meter is used to measure (A) Velocity of flow in an open channel (B) Depth of flow in an open channel (C) Hydraulic jump (D) Depth of channel

Description : The critical depth meter is used to measure (A) Velocity of flow in an open channel (B) Depth of flow in an open channel (C) Hydraulic jump (D) Depth of channel

Last Answer : Answer: Option C

In open channel flow in a rectangular channel, the ratio between the critical depth and the initial depth, when a hydraulic jump occurs is (A) 0.5 (B) 0.84 (C) 1.84 (D) 1.25

Description : In open channel flow in a rectangular channel, the ratio between the critical depth and the initial depth, when a hydraulic jump occurs is (A) 0.5 (B) 0.84 (C) 1.84 (D) 1.25

Last Answer : (C) 1.84

For efficient working of a control meter, its throat length is approximately kept (A) Equal to the critical depth (B) Twice the critical depth (C) Three times the critical depth (D) Four times the critical depth

Description : For efficient working of a control meter, its throat length is approximately kept (A) Equal to the critical depth (B) Twice the critical depth (C) Three times the critical depth (D) Four times the critical depth

Last Answer : Answer: Option C

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Description : The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Last Answer : [ A ] equal

The depth of neutral axis for over reinforced section is ----------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Description : The depth of neutral axis for over reinforced section is ----------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Last Answer : [ B ] Greater than

The depth of neutral axis for under reinforced section is --------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Description : The depth of neutral axis for under reinforced section is --------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Last Answer : [ C ] Less than

The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Description : The most economical section of a trapezoidal channel is one which has hydraulic mean depth equal to (A) 1/2 × depth (B) 1/2 × breadth (C) 1/2 × sloping side (D) 1/4 × (depth + breadth)

Last Answer : Answer: Option A

The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Description : The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Last Answer : Answer: Option A

09. The rise, in water level, which occurs during the transformation of the unstable shooting flow to the stable streaming flow is called hydraulic jump. A) Yes B) No

Description : 09. The rise, in water level, which occurs during the transformation of the unstable shooting flow to the stable streaming flow is called hydraulic jump. A) Yes B) No

Last Answer : A

If the depth of water in an open channel is less than the critical depth, the flow is called (A) Critical flow (B) Turbulent flow (C) Tranquil flow (D) Torrential flow

Description : If the depth of water in an open channel is less than the critical depth, the flow is called (A) Critical flow (B) Turbulent flow (C) Tranquil flow (D) Torrential flow

Last Answer : Answer: Option D

The critical section for finding maximum bending moment for footing under masonry wall is located (A) At the middle of the wall (B) At the edge of the wall (C) Halfway between the middle and edge of the wall (D) At a distance equal to effective depth of footing from the edge of the wall

Description : The critical section for finding maximum bending moment for footing under masonry wall is located (A) At the middle of the wall (B) At the edge of the wall (C) Halfway between the middle and edge of the wall (D) At a distance equal to effective depth of footing from the edge of the wall

Last Answer : Answer: Option C

The porosity of a certain soil sample was found to be 80% and its specific gravity was 2:7; the critical hydraulic gradient will be estimated as (a) 0.34 (b) 0.92 (c) 1.0 (d) 1.5

Description : The porosity of a certain soil sample was found to be 80% and its specific gravity was 2:7; the critical hydraulic gradient will be estimated as (a) 0.34 (b) 0.92 (c) 1.0 (d) 1.5

Last Answer : (a) 0.34

A circular gravity aqueduct is not generally preferred to because of (A) Its maximum hydraulic mean depth (B) Maximum area per unit of wetted perimeter (C) Minimum cost of construction (D) Its proper support on the ground

Description : A circular gravity aqueduct is not generally preferred to because of (A) Its maximum hydraulic mean depth (B) Maximum area per unit of wetted perimeter (C) Minimum cost of construction (D) Its proper support on the ground

Last Answer : (D) Its proper support on the ground

Pick up the correct statement from the following: (A) The phenomenon of quicksand generally occurs in the cohesionless soil (B) At critical hydraulic gradient, the saturated sand becomes quick (C) The critical gradient depends on the void ratio and the specific gravity (D) All the above

Description : Pick up the correct statement from the following: (A) The phenomenon of quicksand generally occurs in the cohesionless soil (B) At critical hydraulic gradient, the saturated sand becomes quick (C) The critical gradient depends on the void ratio and the specific gravity (D) All the above

Last Answer : (D) All the above

If the unit weight of sand particles is 2.696 g/cc. and porosity in loose state is 44%, the critical hydraulic gradient for quick sand condition, is (A) 0.91 (B) 0.92 (C) 0.93 (D) 0.95

Description : If the unit weight of sand particles is 2.696 g/cc. and porosity in loose state is 44%, the critical hydraulic gradient for quick sand condition, is (A) 0.91 (B) 0.92 (C) 0.93 (D) 0.95

Last Answer : (D) 0.95

A critical hydraulic gradient may occur when (A) Flow is in upward direction (B) Seepage pressure is in upward direction (C) Effective pressure is zero (D) All the above

Description : A critical hydraulic gradient may occur when (A) Flow is in upward direction (B) Seepage pressure is in upward direction (C) Effective pressure is zero (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) The rate of flow of water through a vertical strip of the aquifer of unit width and full depth under a unit hydraulic gradient, is called coefficient of transmissibility (C) The flow of water through aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Description : Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) ... aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Last Answer : Answer: Option D

The hydraulic mean depth for a circular pipe of diameter (d) is (A) d/6 (B) d/4 (C) d/2 (D) d

Description : The hydraulic mean depth for a circular pipe of diameter (d) is (A) d/6 (B) d/4 (C) d/2 (D) d

Last Answer : Answer: Option B

The hydraulic mean depth or the hydraulic radius is the ratio of (A) Area of flow and wetted perimeter (B) Wetted perimeter and diameter of pipe (C) Velocity of flow and area of flow (D) None of these

Description : The hydraulic mean depth or the hydraulic radius is the ratio of (A) Area of flow and wetted perimeter (B) Wetted perimeter and diameter of pipe (C) Velocity of flow and area of flow (D) None of these

Last Answer : Answer: Option A

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

If 'x' is the depth of flow in an open channel of large width, then the hydraulic radius is equal to (A) x (B) x/2 (C) x/3 (D) 2x/3

Description : If 'x' is the depth of flow in an open channel of large width, then the hydraulic radius is equal to (A) x (B) x/2 (C) x/3 (D) 2x/3

Last Answer : (A) x

If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Description : If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Last Answer : Option C

If the depth of actual axis in a beam is more than the depth of critical axis, then the beam is called (a) Over reinforced beam (b) Under-reinforced beam (c) Balanced beam (d) Deep beam

Description : If the depth of actual axis in a beam is more than the depth of critical axis, then the beam is called (a) Over reinforced beam (b) Under-reinforced beam (c) Balanced beam (d) Deep beam

Last Answer : (a) Over reinforced beam

If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Description : If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Last Answer : [ A ] Concrete attains its permissible stress earlier

If the depth of water in an open channel is greater than the critical depth, the flow is called (A) Critical flow (B) Turbulent flow (C) Tranquil flow (D) Torrential flow

Description : If the depth of water in an open channel is greater than the critical depth, the flow is called (A) Critical flow (B) Turbulent flow (C) Tranquil flow (D) Torrential flow

Last Answer : Answer: Option C

The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is (A) Less than one (B) Equal to one (C) More than one (D) Equal

Description : The ratio of the moment of inertia of a circular plate and that of a square plate for equal depth, is  (A) Less than one  (B) Equal to one  (C) More than one  (D) Equal 

Last Answer : (D) Equal 

If the output of a dragline for 90° angle of swing at optimum depth of cut is X, then the output for 120° angle of swing at 120 % of optimum depth of cut will be (A) Equal to X (B) More than X (C) Less than X (D) Any of the above

Description : If the output of a dragline for 90° angle of swing at optimum depth of cut is X, then the output for 120° angle of swing at 120 % of optimum depth of cut will be (A) Equal to X (B) More than X (C) Less than X (D) Any of the above

Last Answer : (C) Less than X

Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Description : Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Last Answer : Answer: Option C

In a doubly-reinforced beam if and is the effective depth and is depth of critical neutral axis, the following relationship holds good (A) mc/t = n/(d - n) (B) (m + c)/t = n/(d + n) (C) (t + c)/n = (d + n)/nD) mc/t = (d - n)/t

Description : In a doubly-reinforced beam if and is the effective depth and is depth of critical neutral axis, the following relationship holds good (A) mc/t = n/(d - n) (B) (m + c)/t = n/(d + n) (C) (t + c)/n = (d + n)/n D) mc/t = (d - n)/t

Last Answer : Answer: Option A

If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is (A) [m/(m - r)] d (B) [m/(m + r)] d (C) [(m + r)/m] d (D) [(r - m)/m] d

Description : If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is (A) [m/(m - r)] d (B) [m/(m + r)] d (C) [(m + r)/m] d (D) [(r - m)/m] d

Last Answer : Answer: Option B

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D

The critical depth in a channel can be produced (A) By raising the bottom of the channel (B) By lowering the bottom of the channel (C) By decreasing the width of the channel (D) Both (a) and (c) of above

Description : The critical depth in a channel can be produced (A) By raising the bottom of the channel (B) By lowering the bottom of the channel (C) By decreasing the width of the channel (D) Both (a) and (c) of above

Last Answer : Answer: Option D

15. The depth of water in a channel corresponding to the minimum specific energy is known as critical depth. A) Agree B) Disagree

Description : 15. The depth of water in a channel corresponding to the minimum specific energy is known as critical depth. A) Agree B) Disagree

Last Answer : A

12. The flow at critical depth in an open channel is called torrential flow. A) Yes B) No

Description : 12. The flow at critical depth in an open channel is called torrential flow. A) Yes B) No

Last Answer : B

The discharge in an open channel corresponding to critical depth is (A) Zero (B) Minimum (C) Maximum (D) None of these

Description : The discharge in an open channel corresponding to critical depth is (A) Zero (B) Minimum (C) Maximum (D) None of these

Last Answer : Answer: Option C

Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Last Answer : Answer: Option B

Consider the following statements: In the critical path method of construction planning, Free Float can be. 1. Greater than Total Float. 2. Greater than Independent Float 3. Equal to Total Float. 4. Less than Independent Float. Of these statements (A) 1 and 4 are correct (B) 2 and 3 are correct (C) 1 and 4 are correct (D) 1 and 2 are correct

Description : Consider the following statements: In the critical path method of construction planning, Free Float can be. 1. Greater than Total Float. 2. Greater than Independent Float 3. Equal to Total Float. 4. Less than ... (B) 2 and 3 are correct (C) 1 and 4 are correct (D) 1 and 2 are correct

Last Answer : (B) 2 and 3 are correct

Moment of resistance for a under reinforced section --------- that of a critical section [ A ] Is equal to [ B ] Is always greater than [ C ] Is less than [ D ] May be sometimes greater than

Description : Moment of resistance for a under reinforced section --------- that of a critical section [ A ] Is equal to [ B ] Is always greater than [ C ] Is less than [ D ] May be sometimes greater than

Last Answer : [ C ] Is less than

In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Description : In general, the depth of slab should be ---------------- the minimum depth required for balanced section. [ A ] Equal to [ B ] Less than [ C ] Greater than [ D ] Half of

Last Answer : [ C ] Greater than

If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Description : If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Last Answer : Answer: Option D

The average mean velocity of a stream having depth h, may be obtained by taking the average of the readings of a current meter at a depth of (A) 0.1 h and 0.9 h (B) 0.2 h and 0.8 h (C) 0.3 h and 0.7 h (D) 0.4 h and 0.6 h

Description : The average mean velocity of a stream having depth h, may be obtained by taking the average of the readings of a current meter at a depth of (A) 0.1 h and 0.9 h (B) 0.2 h and 0.8 h (C) 0.3 h and 0.7 h (D) 0.4 h and 0.6 h

Last Answer : Answer: Option B

A circular sewer section is preferred to because A. It is cheaper in construction B. It provides maximum area for a given perimeter C. It provides maximum hydraulic mean depth D. All the above

Description : A circular sewer section is preferred to because A. It is cheaper in construction B. It provides maximum area for a given perimeter C. It provides maximum hydraulic mean depth D. All the above

Last Answer : ANS: D

weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Description : weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Last Answer : ANS: A

Pick up the correct statement from the following: A. The circular section of sewers provides maximum hydraulic mean depth B. The circular sewers are provided for separate sewerage system C. The circular sewers work efficiently if the sections run at least half full D. All the above

Description : Pick up the correct statement from the following: A. The circular section of sewers provides maximum hydraulic mean depth B. The circular sewers are provided for separate sewerage system C. The circular sewers work efficiently if the sections run at least half full D. All the above

Last Answer : ANS: D

The ratio of the depth of flow to the hydraulic radius for the most economical trapezoidal section, in open channel flow is (A) 0.5 (B) 1 (C) 1.5 (D) 2

Description : The ratio of the depth of flow to the hydraulic radius for the most economical trapezoidal section, in open channel flow is (A) 0.5 (B) 1 (C) 1.5 (D) 2

Last Answer : (D) 2

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

If D is the depth of scour below original bed, then the width of launching apron is generally taken as (A) 1.2 D (B) 1.5 D (C) 2.0 D (D) 2.5 D

Description : If D is the depth of scour below original bed, then the width of launching apron is generally taken as (A) 1.2 D (B) 1.5 D (C) 2.0 D (D) 2.5 D

Last Answer : Answer: Option B

In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the earth work is calculated by multiplying the mid-section area by the distance between the two original sections (D) All of the above

Description : In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the ... multiplying the mid-section area by the distance between the two original sections (D) All of the above

Last Answer : (D) All of the above