The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

The diameter of the column head support a flat slab, is generally kept
(A) 0.25 times the span length
(B) 0.25 times the diameter of the column
(C) 4.0 cm larger than the diameter of the column
(D) 5.0 cm larger than the diameter of the column
by

1 Answer

Answer :

Option A
by

Related questions

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Last Answer : Answer: Option B

Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Last Answer : Answer: Option A

Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Last Answer : Answer: Option C

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9

If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5m

Description : If the size of panel in a flat slab is 6 m × 6 m, then as per Indian Standard Code, the widths of column strip and middle strip are (A) 3.0 m and 1.5 m (B) 1.5 m and 3.0 m (C) 3.0 m and 3.0 m (D) 1.5 m and 1.5 m

Last Answer : Answer: Option C

The Effective length of braced column generally varies…………the unsupported length of the column [ A ] 0.25 to 0.50 times [ B ] 0.50 to 1.00 times [ C ] 1.00 to 1.50 times [ D ] 2.00 to 2.50 times

Description : The Effective length of braced column generally varies…………the unsupported length of the column [ A ] 0.25 to 0.50 times [ B ] 0.50 to 1.00 times [ C ] 1.00 to 1.50 times [ D ] 2.00 to 2.50 times

Last Answer : [ B ] 0.50 to 1.00 times

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Last Answer : (B) 12.88

Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Description : Critical section for shear in case of flat slabs is at a distance of (A) Effective depth of slab from periphery of column/drop panel (B) d/2 from periphery of column/capital/ drop panel (C) At the drop panel of slab (D) At the periphery of column

Last Answer : Answer: Option B

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured parallel to the supported edge, the effective width of the slab be is (A) K/x (1 + x/d) + bw (B) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Last Answer : Answer: Option B

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Last Answer : Answer: Option C

The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20

Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20

Last Answer : Answer: Option C

The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Last Answer : (c) 35

The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Last Answer : (c) 30

The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Last Answer : Answer: Option D

The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Last Answer : Answer: Option D

The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is (A) 2.75 cm (B) 3.00 cm (C) 3.50 cm (D) 4.25 cm

Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm  for an eccentric load 100 t for non-development of tension, is  (A) 2.75 cm  (B) 3.00 cm  (C) 3.50 cm  (D) 4.25 cm

Last Answer : (D) 4.25 cm

If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Description : If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Last Answer : Answer: Option D

The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Description : The breadth of the flange of a T-beam is (a) 1/3rd of the effective span of the T-beam (b) Twelve times the depth of slab plus breadth of rib. (c) Centre to centre distance between the adjacent beam. (d) Least of (a) , (b) or (c)

Last Answer : (d) Least of (a) , (b) or (c)

Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Last Answer : Answer: Option B

Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Last Answer : (b) 15, 25, 40 and 75

In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Description : In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.

Last Answer : [ B ] May be increased

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 m

Description : The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 mm

Last Answer : Answer: Option B

The size of mould for bricks, is generally kept (A) A little large to specified size (B) A little small to specified size (C) Equal to specified size (D) 10% larger than specified size

Description : The size of mould for bricks, is generally kept (A) A little large to specified size (B) A little small to specified size (C) Equal to specified size (D) 10% larger than specified size

Last Answer : Answer: Option A

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span (A) 2.5 cm (B) 3.0 cm (C) 4.0 cm (D) 5.0 cm

Description : A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20  meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span  (A) 2.5 cm  (B) 3.0 cm  (C) 4.0 cm  (D) 5.0 cm 

Last Answer : (C) 4.0 cm

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

The raft slab is projected beyond the outer walls of the structure by (A) 5 to 10 cm (B) 15 to 20 cm (C) 25 to 30 cm (D) 30 to 45 cm

Description : The raft slab is projected beyond the outer walls of the structure by (A) 5 to 10 cm (B) 15 to 20 cm (C) 25 to 30 cm (D) 30 to 45 cm

Last Answer : Answer: Option D

The slab is designed as one way if the ratio of long span to short span is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2 (D) Greater than 2

Description : The slab is designed as one way if the ratio of long span to short span is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2 (D) Greater than 2

Last Answer : Answer: Option D

Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept 5 to 7.5 cm below the inlet invert level C. The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Description : Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept ... . The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Last Answer : ANS: D

Pick up the correct statement from the following: (A) The sand in the sand pile is well compacted (B) The sand is kept moist at the time of placing and tamping (C) Sand piles are generally used under column loads (D) All of the above

Description : Pick up the correct statement from the following: (A) The sand in the sand pile is well compacted (B) The sand is kept moist at the time of placing and tamping (C) Sand piles are generally used under column loads (D) All of the above

Last Answer : Answer: Option D

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

The minimum diameter of a sewer is kept A. 10 cm B. 15 cm C. 20 cm D. 25 cm

Description : The minimum diameter of a sewer is kept A. 10 cm B. 15 cm C. 20 cm D. 25 cm

Last Answer : ANS: B

Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Description : Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Last Answer : Answer: Option D

For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Last Answer : Answer: Option D

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Description : If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Last Answer : Answer: Option C

The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Description : The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Last Answer : Answer: Option C

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Description : In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Last Answer : Answer: Option D

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C