The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

The spacing of transverse reinforcement of column is decided by the following consideration.
(A) The least lateral dimension of the column
(B) Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column
(C) Forty-eight times the diameter of transverse reinforcement
(D) All the above
by

1 Answer

Answer :

Answer: Option D
by

Related questions

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Last Answer : Answer: Option D

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Last Answer : Answer: Option D

According to IS: 4561978, the column or the strut is the member whose effective length is greater than (A) The least lateral dimension (B) 2 times the least lateral dimension (C) 3 times the least lateral dimension (D) 4 times the least lateral dimension

Description : According to IS: 4561978, the column or the strut is the member whose effective length is greater than (A) The least lateral dimension (B) 2 times the least lateral dimension (C) 3 times the least lateral dimension (D) 4 times the least lateral dimension

Last Answer : Answer: Option C

If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Description : If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Last Answer : Answer: Option B

Along column is one whose ratio of effective length to its least lateral dimension exceeds (a) 5 (b) 10 (c) 12 (d) 20

Description : Along column is one whose ratio of effective length to its least lateral dimension exceeds (a) 5 (b) 10 (c) 12 (d) 20

Last Answer : (c) 12

The distribution reinforcement is also called ________________reinforcement. (a) Longitudinal (b) Transverse (c) Main (d) None of the these

Description : The distribution reinforcement is also called _______________reinforcement. (a) Longitudinal (b) Transverse (c) Main (d) None of the these

Last Answer : (b) Transverse

Pick up the correct statement from the following: (A) Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling (B) Lateral reinforcement prevents the shearing of concrete on diagonal plane (C) Lateral reinforcement stops breaking away of concrete cover, due to buckling (D) All the above

Description : Pick up the correct statement from the following: (A) Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling (B) Lateral reinforcement prevents ... Lateral reinforcement stops breaking away of concrete cover, due to buckling (D) All the above

Last Answer : Answer: Option D

Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension (A) Two times (B) Three times (C) Four times (D) Five times

Description : Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension (A) Two times (B) Three times (C) Four times (D) Five times

Last Answer : Answer: Option C

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Description : The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Last Answer : [ D ] One – fourth

The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm

Description : The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times

Last Answer : (c) eight times

The limits of percentage p of the longitudinal reinforcement in a column is given by (A) 0.15% to 2% (B) 0.8% to 4% (C) 0.8% to 6% (D) 0.8% to 8%

Description : The limits of percentage p of the longitudinal reinforcement in a column is given by (A) 0.15% to 2% (B) 0.8% to 4% (C) 0.8% to 6% (D) 0.8% to 8%

Last Answer : Answer: Option C

Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Last Answer : Answer: Option B

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

A column is regarded as long column if the ratio of its effective length and lateral dimension, exceeds (A) 10 (B) 15 (C) 20 (D) 25

Description : A column is regarded as long column if the ratio of its effective length and lateral dimension, exceeds (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option B

When the ratio of the effective length of the rectangular columns to its lateral dimension exceeds12, then the column is said to be [ A ] Short column [ B ] Slender column [ C ] Biaxial column [ D ] All the above

Description : When the ratio of the effective length of the rectangular columns to its lateral dimension exceeds12, then the column is said to be [ A ] Short column [ B ] Slender column [ C ] Biaxial column [ D ] All the above

Last Answer : [ B ] Slender column

The purpose of lateral ties in short R.C. columns is to (a) Increase the load carrying capacity of column (b) Facilitate compaction of concrete (c) Facilitate construction (d) Avoid buckling of longitudinal bars

Description : The purpose of lateral ties in short R.C. columns is to (a) Increase the load carrying capacity of column (b) Facilitate compaction of concrete (c) Facilitate construction (d) Avoid buckling of longitudinal bars

Last Answer : (d) Avoid buckling of longitudinal bars

If a circular beam of diameter d experiences a longitudinal strain P/E and a lateral strain 2P/mE, the volumetric strain is (A) (P/E) + (2P/mE) (B) (P/E) - (2P/mE) (C) (P/E) + (mE/2P) (D) (P/E) - (mE/2P)

Description : If a circular beam of diameter d experiences a longitudinal strain P/E and a lateral strain 2P/mE, the volumetric strain is (A) (P/E) + (2P/mE) (B) (P/E) - (2P/mE) (C) (P/E) + (mE/2P) (D) (P/E) - (mE/2P)

Last Answer : (B) (P/E) - (2P/mE)

In a footstep bearing, if the radius of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the radius of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option D

In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option A

In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Description : In a footstep bearing, if the speed of the shaft is doubled, then the torque required to overcome the viscous resistance will be (A) Double (B) Four times (C) Eight times (D) Sixteen times

Last Answer : Answer: Option A

The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Last Answer : [ D ] Smaller of five times the effective depth and 450 mm

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Description : The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Last Answer : Answer: Option D

The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Description : The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Last Answer : Answer: Option C

Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Last Answer : [ C ] 40 mm

The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is (A) 30° (B) 40° (C) 45° (D) All the above

Description : The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is (A) 30° (B) 40° (C) 45° (D) All the above

Last Answer : Answer: Option D

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Last Answer : (D) 1/8

The clear cover in a simply supported slab should not be less than the diameter of the reinforcing bar (a) Correct (b) Incorrect’ (c) Not known (d) None of these

Description : The clear cover in a simply supported slab should not be less than the diameter of the reinforcing bar (a) Correct (b) Incorrect’ (c) Not known (d) None of these

Last Answer : (a) Correct

Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Description : Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Last Answer : [ C ] the effective length to least lateral design

In limit state approach, spacing of main reinforcement controls primarily (a) Cracking (b) Deflection (c ) Durability (d) Collapse

Description : In limit state approach, spacing of main reinforcement controls primarily (a) Cracking (b) Deflection (c ) Durability (d) Collapse

Last Answer : (a) Cracking

The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Last Answer : (c ) 144 mm

Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Description : Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d

Last Answer : [ D ] d

According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

Maximum allowable spacing of shear reinforcement for vertical stirrups is restricted to [ A ] d [ B ] 0.45 d [ C ] 0.75 d [ D ] 0.90 d

Description : Maximum allowable spacing of shear reinforcement for vertical stirrups is restricted to [ A ] d [ B ] 0.45 d [ C ] 0.75 d [ D ] 0.90 d

Last Answer : [ C ] 0.75 d

According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Last Answer : [ C ] lesser of 0.75 d or 300 mm

The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Lesser of (a) and (b)

A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Last Answer : Answer: Option D

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Last Answer : Answer: Option D

The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Last Answer : (d) All the above