The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

The diameter of transverse reinforcement of columns should be equal to one-fourth of the
diameter of the main steel rods but not less than
(A) 4 mm
(B) 5 mm
(C) 6 mm
(D) 7 mm
by

1 Answer

Answer :

Answer: Option D
by

Related questions

The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Description : The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal ... column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Last Answer : Answer: Option D

The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Description : The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Last Answer : Answer: Option D

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The diameter of main bars in R.C.C. columns, shall not be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Description : The diameter of main bars in R.C.C. columns, shall not be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Last Answer : Answer: Option D

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Description : The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Last Answer : [ A ] 25 mm

If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Description : If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Last Answer : Answer: Option D

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Last Answer : Answer: Option D

The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Last Answer : (d) All the above

The distribution reinforcement is also called ________________reinforcement. (a) Longitudinal (b) Transverse (c) Main (d) None of the these

Description : The distribution reinforcement is also called _______________reinforcement. (a) Longitudinal (b) Transverse (c) Main (d) None of the these

Last Answer : (b) Transverse

The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Description : The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Last Answer : (d) All of the above.

Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Description : Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter

Last Answer : Answer: Option D

The minimum clear cover for R.C.C. columns shall be (A) Greater of 40 mm or diameter (B) Smaller of 40 mm or diameter (C) Greater of 25 mm or diameter (D) Smaller of 25 mm or diameter

Description : The minimum clear cover for R.C.C. columns shall be (A) Greater of 40 mm or diameter (B) Smaller of 40 mm or diameter (C) Greater of 25 mm or diameter (D) Smaller of 25 mm or diameter

Last Answer : Answer: Option C

The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Last Answer : [ D ] Smaller of five times the effective depth and 450 mm

A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Last Answer : Answer: Option D

The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Last Answer : (c ) 144 mm

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Last Answer : Answer: Option B

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Last Answer : d) 41

Pick up the correct statement from the following: (A) Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling (B) Lateral reinforcement prevents the shearing of concrete on diagonal plane (C) Lateral reinforcement stops breaking away of concrete cover, due to buckling (D) All the above

Description : Pick up the correct statement from the following: (A) Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling (B) Lateral reinforcement prevents ... Lateral reinforcement stops breaking away of concrete cover, due to buckling (D) All the above

Last Answer : Answer: Option D

The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Description : The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Last Answer : (c) 8 to 14mm

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Description : The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Last Answer : Answer: Option D

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above

Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above

Last Answer : Answer: Option D

The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Last Answer : [ A ] 0.12 percent of gross cross sectional area

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Description : The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Last Answer : [ D ] One – fourth

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Description : If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Last Answer : Answer: Option B

The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Description : The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Last Answer : Answer: Option D

A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Description : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Last Answer : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale ... (C) 0.053 cm (D) 0.529 cm

A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Description : A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Last Answer : (B) 0.2275 mm

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N

Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in  diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive  load to remove the clearance, is  (A) 25 N  (B) 30 N  (C) 35 N  (D) 40 N 

Last Answer : (C) 35 N 

The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Last Answer : (B) 102 kg

In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time

Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time

Last Answer : Answer: Option B

Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Last Answer : [ C ] 40 mm