A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just next to pipe (i.e., inside) (B) The better insulating material should be put outside (C) Either of the insulating material could be put on either side (D) Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)

A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place
(A) The better insulation material should be put just next to pipe (i.e., inside) (B) The better insulating material should be put outside
(C) Either of the insulating material could be put on either side (D) Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)
by

1 Answer

Answer :

(A) The better insulation material should be put just next to pipe (i.e., inside)
by

Related questions

A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will (A) Increase (B) Decrease (C) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Description : A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted ... ) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Last Answer : Option C

The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Description : The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Last Answer : (B) 2K/h0

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Description : The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Last Answer : (C) 35°C

Routine maintenance of dry-type transformers should include ______________. A. preventing the entrance of water from broken pipe lines steam lines B. keeping protective surfaces and insulating bushings free of dirt and conductive debris C. periodic testing of insulation resistance with a megger D. all of the above

Description : Routine maintenance of dry-type transformers should include ______________. A. preventing the entrance of water from broken pipe lines steam lines B. keeping protective surfaces and insulating bushings free of ... debris C. periodic testing of insulation resistance with a megger D. all of the above

Last Answer : Answer: D

Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is ‘3k/l’. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?(A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Description : Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l'. If the wall temperature ... wall temperature in degree centigrade? (A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Last Answer : (C) 81.25

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is (A) Finned tube heat exchanger with air inside and steam outside (B) Finned tube heat exchanger with air outside and steam inside (C) Shell and tube heat exchanger with air inside tubes and steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Description : Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both ... steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Last Answer : (B) Finned tube heat exchanger with air outside and steam inside

The critical radius of insulation for cylindrical pipe is (where, hi = heat transfer coefficient at inside of the pipe) (A) K/h0 (B) 2K/h0 (C) hi /K (D) 2hi /K

Description : The critical radius of insulation for cylindrical pipe is (where, hi = heat transfer coefficient at inside of the pipe) (A) K/h0 (B) 2K/h0 (C) hi /K (D) 2hi /K

Last Answer : (A) K/h0

A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature difference across the wall is 36°C. The temperature difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Description : A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature ... difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Last Answer : (B) 12

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

Low thermal conductivity of heat insulating materials is due to its (A) Dense structure (B) High proportion of air space (C) High specific heat (D) None of these

Description : Low thermal conductivity of heat insulating materials is due to its (A) Dense structure (B) High proportion of air space (C) High specific heat (D) None of these

Last Answer : (B) High proportion of air space

The breakdown of insulation of the cable can be avoided economically by the use of (a) inter-sheaths (b) insulating materials with different dielectric constants (c) both (a) and (b) (d) none of the above

Description : The breakdown of insulation of the cable can be avoided economically by the use of (a) inter-sheaths (b) insulating materials with different dielectric constants (c) both (a) and (b) (d) none of the above

Last Answer : (c) both (a) and (b)

Thermal conductivities of most of the liquids __________ with rise in temperature.(A) Increases (B) Decreases (C) Remains unchanged (D) May increase or decrease; depends on the liquid

Description : Thermal conductivities of most of the liquids __________ with rise in temperature. (A) Increases (B) Decreases (C) Remains unchanged (D) May increase or decrease; depends on the liquid

Last Answer : (B) Decreases

At constant temperature, the thermal conductivities of gases__________ with rise in pressure.(A) Decrease(B) Increase(C) Remain unchanged(D) May increase or decrease; depends on the pressure

Description : At constant temperature, the thermal conductivities of gases__________ with rise in pressure. (A) Decrease (B) Increase (C) Remain unchanged (D) May increase or decrease; depends on the pressure

Last Answer : (A) Decrease

State various thermal insulating materials. State any two properties of insulating material

Description : State various thermal insulating materials. State any two properties of insulating material

Last Answer : Thermal insulating materials: 1) Asbestos 2) Aluminum Foil 3) Thermocol 4) Saw dust 5) Cork board slabs 6) Foam glass 7) Rock Wool 8) Glass Wool 9) ... . h) Presence of Moisture: with the increase in moisture content, the coefficient of thermal conductivity rises greatly

Which of the following is the most widely used heat insulating material for pipelines carrying steam? (A) Tar dolomite bricks followed by asbestos (B) Fireclay refractory followed by aluminium sheet (C) Cotton followed by aluminium foil (D) 85% magnesia cement and glass wool

Description : Which of the following is the most widely used heat insulating material for pipelines carrying steam? (A) Tar dolomite bricks followed by asbestos (B) Fireclay refractory followed by aluminium sheet (C) Cotton followed by aluminium foil (D) 85% magnesia cement and glass wool

Last Answer : (D) 85% magnesia cement and glass wool

Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Last Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

Which of the following have the highest thermal conductivities?  a. liquids  b. gases  c. metals  d. solids other than metals

Description : Which of the following have the highest thermal conductivities?  a. liquids  b. gases  c. metals  d. solids other than metals

Last Answer : metals

Which of the following statements best describes the material known as varnished cambric? A. Felted asbestos sealed with varnish. B. Cotton cloth coated with insulating varnish. C. Rubber insulation coated with a layer of tin. D. Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish.

Description : Which of the following statements best describes the material known as varnished cambric? A. Felted asbestos sealed with varnish. B. Cotton cloth coated with insulating varnish. C. Rubber ... Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish.

Last Answer : Answer: B

Electrical leads and insulation on a motor should be painted with ____________. A. heat-resisting acrylic B. heat-resisting aluminum C. insulating varnish D. insulating white lead

Description : Electrical leads and insulation on a motor should be painted with ____________. A. heat-resisting acrylic B. heat-resisting aluminum C. insulating varnish D. insulating white lead

Last Answer : Answer: C

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. Specific heat of block material is 0.4 kJ.kg-1. K-1. Ignoring the effect of expansion and contraction and also the heat capacity to tank, the total entropy change in kJ.kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Description : A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. ... .kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Last Answer : (B) 0

An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Description : An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Last Answer : increases

Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Description : Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Last Answer : Rate of heat transfer by radiation Assume length of pipe = 1 m

For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease(B) Increase(C) First decrease and then increase(D) First increase and then decrease

Description : For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease (B) Increase (C) First decrease and then increase (D) First increase and then decrease

Last Answer : (D) First increase and then decrease

State any two electrical, mechanical and thermal properties of insulating materials.

Description : State any two electrical, mechanical and thermal properties of insulating materials. 

Last Answer : i) Electrical Properties of insulating material:- 1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high dielectric strength. 4. It should have low ... . 4. Ii should have thermal Stability. 5. Co-efficient of thermal expansion should be low.

State the Properties of thermal insulating materials.

Description : State the Properties of thermal insulating materials.

Last Answer : Properties of thermal insulating materials: 1) Thermal insulating should be bio resistant and dry. 2) Thermal resistant should be chemically resistant and fire proof. 3) Thermal resisting ... in the moisture content in the material, the coefficient of thermal conductivity rises greatly.

Which of the following is the most widely used insulating material for steam carrying pipelines? (A) Ceramic fibre blanket (B) Glass wool and 85% magnesia (C) Vermiculite (D) Slag wool

Description : Which of the following is the most widely used insulating material for steam carrying pipelines? (A) Ceramic fibre blanket (B) Glass wool and 85% magnesia (C) Vermiculite (D) Slag wool

Last Answer : (B) Glass wool and 85% magnesia

Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Description : Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Last Answer : (C) Double pipe type with fin on air side

Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Description : Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Last Answer : (C) Salt bath furnace

Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Description : Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Last Answer : (A) Is an electrical insulating material

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Description : Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Last Answer : Option D

Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Description : Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Last Answer : (B) Sum of all resistances

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Last Answer : Answer: A

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the machine secured B. millivolt meter and a jumper with the machine running C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Last Answer : Answer: B

. If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary layer (C) Thermal & concentration boundary layers are of equal thickness (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Description : . If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary ... (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Last Answer : (A) Thermal boundary layer lies inside the concentration boundary layer

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

State failure phenomena observed in insulating material. State four reasons for failure of gaseous and solid dielectric materials.

Description : State failure phenomena observed in insulating material. State four reasons for failure of gaseous and solid dielectric materials. 

Last Answer : Failure phenomena in insulating material means the dielectric property fails :  The dielectric failure mean the dielectric strength of insulating material reduces due to high voltages or high ... 6. Due to poor maintenance of insulating material there may be possibility dielectric failure 

Give classification of insulating materials on the basis of state of material and give one application of each.

Description : Give classification of insulating materials on the basis of state of material and give one application of each.

Last Answer : Classification of Insulating material State of material   Application Solid insulating materials Wood, rubber, plastic, PVC, glass, porcelain, mica, Polypropylene film etc.   ... Switchgears, gas pressures cables, circuit breakers, generator cooling systems and X-ray apparatus

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side