For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease(B) Increase(C) First decrease and then increase(D) First increase and then decrease

For a given ambient air temperature with increase in the thickness of

insulation of a hot cylindrical pipe, the rate of heat loss from the surface

would

(A) Decrease

(B) Increase

(C) First decrease and then increase

(D) First increase and then decrease

by

1 Answer

Answer :

(D) First increase and then decrease

by

Related questions

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will (A) Increase (B) Decrease (C) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Description : A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted ... ) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Last Answer : Option C

The critical radius of insulation for cylindrical pipe is (where, hi = heat transfer coefficient at inside of the pipe) (A) K/h0 (B) 2K/h0 (C) hi /K (D) 2hi /K

Description : The critical radius of insulation for cylindrical pipe is (where, hi = heat transfer coefficient at inside of the pipe) (A) K/h0 (B) 2K/h0 (C) hi /K (D) 2hi /K

Last Answer : (A) K/h0

Loss of heat from untagged steam pipe to the ambient air is by (A) Conduction (B) Convection (C) Radiation (D) All (A), (B) & (C)

Description : Loss of heat from untagged steam pipe to the ambient air is by (A) Conduction (B) Convection (C) Radiation (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Description : Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Last Answer : Option D

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Upto the critical radius of insulation, added insulation, will (A) Increase the heat loss (B) Decrease heat loss and will have no effect beyond that (C) Decrease heat flux (D) Reduce convection heat loss compared to conduction heat less

Description : Upto the critical radius of insulation, added insulation, will (A) Increase the heat loss (B) Decrease heat loss and will have no effect beyond that (C) Decrease heat flux (D) Reduce convection heat loss compared to conduction heat less

Last Answer : Option B

A cylindrical cable of core radius 1.25cm and impregnated paper insulation of thickness 2.13cm and relative permittivity 3.5. Compute the capacitance of the cable/km (in nF

Description : A cylindrical cable of core radius 1.25cm and impregnated paper insulation of thickness 2.13cm and relative permittivity 3.5. Compute the capacitance of the cable/km (in nF

Last Answer : To calculate the capacitance of the cable per kilometer, you can use the following formula: C = ε * ε0 * A / d where: C is the capacitance of the cable per kilometer (in farads) ε is ... * 10^9 = 644 nF/km So the capacitance of the cable per kilometer would be approximately 644 nanofarads.

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

In a hot water heating system, there is cylindrical pipe of length 28 m and diameter 5 cm. Find the total radiating surface in the system. -Maths 9th

Description : In a hot water heating system, there is cylindrical pipe of length 28 m and diameter 5 cm. Find the total radiating surface in the system. -Maths 9th

Last Answer : Height of cylindrical pipe = Length of cylindrical pipe = 28m Radius of circular end of pipe = diameter/ 2 = 5/2 cm = 2.5cm = 0.025m Now, CSA of cylindrical pipe = 2πrh, where r = radius and h = height of ... = 2 (22/7) 0.025 28 m2 = 4.4m2 The area of the radiating surface of the system is 4.4m2.

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Description : Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Last Answer : (B) Thickness

A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just next to pipe (i.e., inside) (B) The better insulating material should be put outside (C) Either of the insulating material could be put on either side (D) Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)

Description : A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place (A) The better insulation material should be put just ... to which insulating material is to be put inside (i.e., just next to the pipe)

Last Answer : (A) The better insulation material should be put just next to pipe (i.e., inside)

In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter B. help the windings to cool to ambient temperature C. release any residual capacitive charge from the windings D. help the windings to cool to the same temperature as the ground test connection

Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection

Last Answer : Answer: C

Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Description : Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Last Answer : Answer: D

One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature of 40°C C. minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Description : One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature ... . minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Last Answer : Answer: B

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (B) Fluctuation of ambient temperature during day and night

Which of the following statements regarding evacuated tube collectors (ETC) are true? i) ETC is used for high temperatures upto 150oC ii) because of use of vacuum between two concentric glass tube, higher amount of heat is retained in ETC iii) heat loss due to conduction back to atmosphere from ETC is high iv) performance of evacuated tube is highly dependent upon the ambient temperature i & iii b) ii & iii c) i & iv d) i & ii

Description : Which of the following statements regarding evacuated tube collectors (ETC) are true? i) ETC is used for high temperatures upto 150oC ii) because of use of vacuum between two concentric glass tube, higher amount of heat is ... upon the ambient temperature i & iii b) ii & iii c) i & iv d) i & ii

Last Answer : d) i & ii

For the air water system under ambient conditions, the adiabatic saturation temperature and the wet bulb temperature are nearly equal, because (A) Water has a high latent heat of evaporation (B) Lewis number is close to unity (C) They are always equal under all circumstances

Description : For the air water system under ambient conditions, the adiabatic saturation temperature and the wet bulb temperature are nearly equal, because (A) Water has a high latent heat of evaporation (B) Lewis number is close to unity (C) They are always equal under all circumstances

Last Answer : (A) Water has a high latent heat of evaporation

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

Where a thermal-acting breaker is required to be used in an area of unusually high, low, or constantly fluctuating temperatures, an ambient compensating element must be used. This element consists of a ______________. A. cylindrical spring on the contact arm B. conical spring on the contact arm C. second bimetal element D. second electromagnet

Description : Where a thermal-acting breaker is required to be used in an area of unusually high, low, or constantly fluctuating temperatures, an ambient compensating element must be used. This element consists of ... arm B. conical spring on the contact arm C. second bimetal element D. second electromagnet

Last Answer : Answer: C

The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number(A) Increases(B) Decreases(C) Remain same(D) May increase or decrease.

Description : The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number. (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease

Last Answer : (B) Decreases

What is the Water Regulations the maximum permissible length of dead leg without insulation from the top of a hot water cylinder to the outlet tap for a 22mm pipe?

Description : What is the Water Regulations the maximum permissible length of dead leg without insulation from the top of a hot water cylinder to the outlet tap for a 22mm pipe?

Last Answer : 8m

What is the Water Regulations the maximum permissible length of dead leg without insulation from the top of a hot water cylinder to the outlet tap for a 22mm pipe i?

Description : What is the Water Regulations the maximum permissible length of dead leg without insulation from the top of a hot water cylinder to the outlet tap for a 22mm pipe i?

Last Answer : 8m

Pick out the wrong statement pertaining to solvent extraction of oil. Rate of extraction (A) Decreases with decrease of thickness of the flakes(B) Increases with the increasing flake size keeping the flake thicknessconstant(C) Increases considerably with the rise of temperature(D) Decreases as the moisture content of flakes increases

Description : Pick out the wrong statement pertaining to solvent extraction of oil. Rate of extraction (A) Decreases with decrease of thickness of the flakes (B) Increases with the increasing flake size ... considerably with the rise of temperature (D) Decreases as the moisture content of flakes increases

Last Answer : (D) Decreases as the moisture content of flakes increases

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

The insulation of electric generators during short idle periods should be _____________. A. allowed to cool slowly to ambient temperatures B. flashed with direct current to remove any residual magnetism C. kept warm by using strip or space heaters D. relieved of all capacitive charge by grounding the conductors

Description : The insulation of electric generators during short idle periods should be _____________. A. allowed to cool slowly to ambient temperatures B. flashed with direct current to remove any residual ... using strip or space heaters D. relieved of all capacitive charge by grounding the conductors

Last Answer : Answer: C

When the current flow through a copper wire increases, its _____________. A. resistance will decrease B. insulation will burn C. temperature will increase D. conductivity will increase

Description : When the current flow through a copper wire increases, its _____________. A. resistance will decrease B. insulation will burn C. temperature will increase D. conductivity will increase

Last Answer : Answer: C

With increase in the schedule number of a pipe of a particular nominal size, the (A) Wall thickness also increases (B) I.D. of the pipe decreases (C) O.D. of the pipe remains constant (D) All (A), (B) and (C)

Description : With increase in the schedule number of a pipe of a particular nominal size, the (A) Wall thickness also increases (B) I.D. of the pipe decreases (C) O.D. of the pipe remains constant (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For a given Reynold number as d/D for an orifice increases, Cd will (where, d & D are orifice & pipe diameters respectively). (A) Increase (B) Decrease (C) Remain constant (D) Either (A) or (B); depends on other factors

Description : For a given Reynold number as d/D for an orifice increases, Cd will (where, d & D are orifice & pipe diameters respectively). (A) Increase (B) Decrease (C) Remain constant (D) Either (A) or (B); depends on other factors

Last Answer : (A) Increase

For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Description : For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Last Answer : (A) Decreases

Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Description : Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Last Answer : (A) Increase

Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Description : Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Last Answer : (A) Increase

A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Last Answer : (B) 0.1

One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m-1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is (A) 100 (B) 900 (C) 9000 (D) 10000

Description : One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m-1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is (A) 100 (B) 900 (C) 9000 (D) 10000

Last Answer : (D) 10000

The critical radius 'r' of insulation on a pipe is given by (A) r = 2k/h (B) r = k/h (C) r = k/2h (D) r = h/k

Description : The critical radius 'r' of insulation on a pipe is given by (A) r = 2k/h (B) r = k/h (C) r = k/2h (D) r = h/k

Last Answer : (B) r = k/h

Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the oil may cause the sheath to burst (c) Unequal expansion may create voids in the insulation which will lead to ionization (d) The thermal instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Description : Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the ... instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Last Answer : (e) All of the above

. If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Description : . If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Last Answer : (C) Increase by 2 16

If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Description : If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Last Answer : Answer: C

Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Description : Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Last Answer : (D) None of these

The pipe wall thickness is minimum for a pipe of given nominal size having schedule number (A) 160 (B) 120 (C) 80 (D) 40

Description : The pipe wall thickness is minimum for a pipe of given nominal size having schedule number (A) 160 (B) 120 (C) 80 (D) 40

Last Answer : (D) 40

Schedule number of a pipe, which is a measure of its wall thickness, is given by (A) 1000 P'/S (B) 100 P'/S (C) 1000 S/P' (D) 10000 P'/S

Description : Schedule number of a pipe, which is a measure of its wall thickness, is given by (A) 1000 P'/S (B) 100 P'/S (C) 1000 S/P' (D) 10000 P'/S

Last Answer : (A) 1000 P'/S

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an increase in diameter and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Description : When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an ... and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Last Answer : b) an increase in diameter and length of the shell

If the molar heat capacities (Cp or Cv) of the reactants and products of a chemical reaction are identical, then, with the increase in temperature, the heat of reaction will (A) Increase (B) Decrease (C) Remain unaltered (D) Increase or decrease; depends on the particular reaction

Description : If the molar heat capacities (Cp or Cv) of the reactants and products of a chemical reaction are identical, then, with the increase in temperature, the heat of reaction will (A) Increase (B) Decrease (C) Remain unaltered (D) Increase or decrease; depends on the particular reaction

Last Answer : (C) Remain unaltered