Pick up the correct statement from the following: (A) If the slope of the curve of a mass diagram in the direction of increasing abscissa is downward, it indicates an embankment (B) The vertical distance between a maximum ordinate and the next forward maximum ordinate represents the whole volume of the embankment (C) The vertical distance between a minimum ordinate and the next forward maximum ordinate represents the whole volume of a cutting (D) All the above

Pick up the correct statement from the following:
(A) If the slope of the curve of a mass diagram in the direction of increasing abscissa is
downward, it indicates an embankment
(B) The vertical distance between a maximum ordinate and the next forward maximum ordinate
represents the whole volume of the embankment
(C) The vertical distance between a minimum ordinate and the next forward maximum ordinate
represents the whole volume of a cutting
(D) All the above
by

1 Answer

Answer :

(D) All the above
by

Related questions

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Find the point on the curve `y^2dot` `8xdot` for which the abscissa and ordinate change at the same rate.

Description : Find the point on the curve `y^2dot` `8xdot` for which the abscissa and ordinate change at the same rate.

Last Answer : Find the point on the curve `y^2dot` `8xdot` for which the abscissa and ordinate change at the same rate.

Long run supply curve of a increasing cost industry is (a) Horizontal line overlapping X axis ; (b) Upward sloping line; (c) Downward sloping line ; (d) Vertical line

Description : Long run supply curve of a increasing cost industry is (a) Horizontal line overlapping X axis ; (b) Upward sloping line; (c) Downward sloping line ; (d) Vertical line 

Last Answer : (b) Upward sloping line; 

The side slope of formation in embankment /cutting depends on a) Shearing strength of soil and its angle of repose* b) Angle of repose c) Bearing capacity of the soil d) Optimum moisture content of the soil

Description : The side slope of formation in embankment /cutting depends on a) Shearing strength of soil and its angle of repose* b) Angle of repose c) Bearing capacity of the soil d) Optimum moisture content of the soil

Last Answer : a) Shearing strength of soil and its angle of repose*

Express the given statement in the form of a linear equation in two variables. The sum of the ordinate and abscissa of a point is 6. -Maths 9th

Description : Express the given statement in the form of a linear equation in two variables. The sum of the ordinate and abscissa of a point is 6. -Maths 9th

Last Answer : Solution :- x+y = 6

The ordinate of a point is thrice its abscissa. Express the statement in the form of a linear equation in two variables. -Maths 9th

Description : The ordinate of a point is thrice its abscissa. Express the statement in the form of a linear equation in two variables. -Maths 9th

Last Answer : answer:

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) In order to check up the average depth of excavation, 'Dead man s' are left at the midwidths of borrow pits (B) The earthwork calculation in excavation is made from the difference in levels obtained with a level (C) The earth work in excavation to form the road embankment includes the formation of correct profile and depositing the soil in layers (D) All the above

Description : Pick up the correct statement from the following: (A) In order to check up the average depth of excavation, 'Dead man s' are left at the midwidths of borrow pits (B) The earthwork ... embankment includes the formation of correct profile and depositing the soil in layers (D) All the above

Last Answer : (D) All the above

For measuring flow by a Venturimeter, if should be installed in (A) Vertical line (B) Horizontal line (C) Inclined line with flow downward (D) In any direction and in any location

Description : For measuring flow by a Venturimeter, if should be installed in (A) Vertical line (B) Horizontal line (C) Inclined line with flow downward (D) In any direction and in any location

Last Answer : Answer: Option D

Signs of the abscissa and ordinate of a point in the second quadrant are respectively. -Maths 9th

Description : Signs of the abscissa and ordinate of a point in the second quadrant are respectively. -Maths 9th

Last Answer : (C) In second quadrant, X-axis is negative and Y-axis is positive. So, sign of abscissa of a point is negative and sign of ordinate of a point is positive.

The points whose abscissa and ordinate have different signs will lie in -Maths 9th

Description : The points whose abscissa and ordinate have different signs will lie in -Maths 9th

Last Answer : (d) The points whose abscissa and ordinate have different signs will be of the form (-x, y) or (x, – y)and these points will lie in II and IV quadrants.

Write the linear equation such that each point on its graph has an ordinate 3 times its abscissa. -Maths 9th

Description : Write the linear equation such that each point on its graph has an ordinate 3 times its abscissa. -Maths 9th

Last Answer : Let the abscissa of the point be x, According to the question, Ordinate (y) = 3 x Abscissa ⇒ y=3x When x = 1, then y = 3 x 1 = 3 and when x = 2, then y = 3 x 2 = 6. Here, ... the line AB. Hence, y = 3x is the required equation such that each point on its graph has an ordinate 3 times its abscissa.

Signs of the abscissa and ordinate of a point in the second quadrant are respectively. -Maths 9th

Description : Signs of the abscissa and ordinate of a point in the second quadrant are respectively. -Maths 9th

Last Answer : (C) In second quadrant, X-axis is negative and Y-axis is positive. So, sign of abscissa of a point is negative and sign of ordinate of a point is positive.

The points whose abscissa and ordinate have different signs will lie in -Maths 9th

Description : The points whose abscissa and ordinate have different signs will lie in -Maths 9th

Last Answer : (d) The points whose abscissa and ordinate have different signs will be of the form (-x, y) or (x, – y)and these points will lie in II and IV quadrants.

Write the linear equation such that each point on its graph has an ordinate 3 times its abscissa. -Maths 9th

Description : Write the linear equation such that each point on its graph has an ordinate 3 times its abscissa. -Maths 9th

Last Answer : Let the abscissa of the point be x, According to the question, Ordinate (y) = 3 x Abscissa ⇒ y=3x When x = 1, then y = 3 x 1 = 3 and when x = 2, then y = 3 x 2 = 6. Here, ... the line AB. Hence, y = 3x is the required equation such that each point on its graph has an ordinate 3 times its abscissa.

Determine the point on the graph of the linear equation x + y = 6, whose ordinate is 2 times its abscissa. -Maths 9th

Description : Determine the point on the graph of the linear equation x + y = 6, whose ordinate is 2 times its abscissa. -Maths 9th

Last Answer : Solution :-

The point in which abscissa and ordinate have different signs will lie in which quadrant (s)? -Maths 9th

Description : The point in which abscissa and ordinate have different signs will lie in which quadrant (s)? -Maths 9th

Last Answer : Solution :- II and IV quadrants.

linear equation such that each point on its graph has an ordinate one more than 3×1÷2 times its abscissa -Maths 9th

Description : linear equation such that each point on its graph has an ordinate one more than 3×1÷2 times its abscissa -Maths 9th

Last Answer : This answer was deleted by our moderators...

The product of the abscissa and the ordinate of a point P is negative. In which quadrants can the point lie ? -Maths 9th

Description : The product of the abscissa and the ordinate of a point P is negative. In which quadrants can the point lie ? -Maths 9th

Last Answer : answer:

What do you mean by Co-ordinates (Abscissa and Ordinate)? Explain with figure. -Maths 9th

Description : What do you mean by Co-ordinates (Abscissa and Ordinate)? Explain with figure. -Maths 9th

Last Answer : Co-ordinate Geometry is that branch of geometry in which two numbers, called co-ordinates are used to indicate the position of a point in a plane and which make use of algebraic methods in the study of geometric figures.

The point whose abscissa is equal to its ordinate and which is equidistant from A(–1, 0) and B(0, 5) is -Maths 9th

Description : The point whose abscissa is equal to its ordinate and which is equidistant from A(–1, 0) and B(0, 5) is -Maths 9th

Last Answer : Putting \(x\) = 0 in equation of one of the lines say 9\(x\) + 40y -20 = 0, we get y = \(rac{1}{2}\)∴ A point on 9\(x\) + 40y - 20 = 0 is \(\big(0,rac{1}{2}\big)\)∴ Distance of \(\big(0,rac{1}{2}\big) ... imesrac{1}{2}+21\big|}{\sqrt{9^2+40^2}}\) = \(rac{|41|}{\sqrt{1681}}\) = \(rac{41}{41}\) = 1.

Without plotting the points indicate the quadrant in which they lie, if : (i) ordinate is 5 and abscissa is – 3 (ii) abscissa is -5 and ordinate is – 3 -Maths 9th

Description : Without plotting the points indicate the quadrant in which they lie, if : (i) ordinate is 5 and abscissa is – 3 (ii) abscissa is -5 and ordinate is – 3 -Maths 9th

Last Answer : answer:

Without plotting the points indicate the quadrant in which they will lie, if (i) the ordinate is 5 and abscissa is – 3 -Maths 9th

Description : Without plotting the points indicate the quadrant in which they will lie, if (i) the ordinate is 5 and abscissa is – 3 -Maths 9th

Last Answer : (i) In the point (−3,5) abscissa is negative and ordinate is positive, so it lies in the second quadrant. (ii) In the point (−5,−3) abscissa and ordinate both are negative, so it lies in the ... . (iv) In the point (3,5) abscissa and ordinate both are positive, so it lies in the first quadrant

Pick up the correct statement from the following (A) The contour lines having the same elevation cannot unite and continue as one line (B) A contour can not end abruptly, but must ultimately close itself not necessarily within the limits of map (C) The direction of steepest slope at a point on a contour is at right angles to the contour (D) All the above

Description : Pick up the correct statement from the following (A) The contour lines having the same elevation cannot unite and continue as one line (B) A contour can not end abruptly, but must ultimately close itself not ... slope at a point on a contour is at right angles to the contour (D) All the above

Last Answer : (D) All the above

According to traditional approach the factor responsible for operation of downward slope of demand curve are (a) Change in number of consumers ; (b) Law of decreasing marginal utility (c) Alternative uses of goods ; (d) All the three

Description : According to traditional approach the factor responsible for operation of downward slope of demand curve are (a) Change in number of consumers ; (b) Law of decreasing marginal utility (c) Alternative uses of goods ; (d) All the three

Last Answer : (d) All the three

If B is the width of formation, d is the height of the embankment, side slope S : 1, for a highway with no transverse slope, the area of cross-section is (A) B + d + Sd (B) Bd + Sd2 (C) B × d - Sd1/2 (D) ½ (Bd + Sd2

Description : If B is the width of formation, d is the height of the embankment, side slope S : 1, for a highway with no transverse slope, the area of cross-section is (A) B + d + Sd (B) Bd + Sd2 (C) B × d - Sd1/2 (D) ½ (Bd + Sd2

Last Answer : (B) Bd + Sd2

Pick up the correct statement from the following: (A) The structural member subjected to compression and whose dimensions are small as compared to its length, is called a stmt (B) The vertical compression members are generally known as columns or stanchions (C) Deflection in lateral direction of a long column, is generally known as buckling (D) All the above

Description : Pick up the correct statement from the following:  (A) The structural member subjected to compression and whose dimensions are small as  compared to its length, is called a stmt  (B) The ... in lateral direction of a long column, is generally known as buckling  (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) When the electric field oscillates in the direction of the electric vector, a plane polarised wave is formed (B) When the electric vector is in the plane of incidence, vertical polarisation is formed (C) When the electric vector is at right angles to the plane of incidence, horizontal polarization wave is formed (D) All of these

Description : Pick up the correct statement from the following: (A) When the electric field oscillates in the direction of the electric vector, a plane polarised wave is formed (B) When the electric vector is ... right angles to the plane of incidence, horizontal polarization wave is formed (D) All of these

Last Answer : Answer: Option D

A perfectly elastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis; (c) U shaped ; (d) Downward sloping

Description : A perfectly elastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis; (c) U shaped ; (d) Downward sloping

Last Answer : the aggregate demand curve

A perfect inelastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis ; (c) U shaped; (d) Downward sloping

Description : A perfect inelastic supply curve will be (a) Parallel to Y axis or a vertical line ; (b) Parallel to X axis ; (c) U shaped; (d) Downward sloping

Last Answer : (a) Parallel to Y axis or a vertical line ;

Some statement about Ellingham diagram (a) Increase in the slope of the line on +ve side indicates the phase ransformation (b) Metal oxide decomposes

Description : Some statement about Ellingham diagram (a) Increase in the slope of the line on +ve side indicates the phase ransformation (b) Metal oxide decomposes

Last Answer : Some statement about Ellingham diagram (a) Increase in the slope of the line on +ve side indicates the phase ... C. Only b and c D. a,b and c

Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by a straight horizontal line on the grading curve (C) The omission of a certain size of aggregate in concrete increases the workability but also increases the liability to segregation (D) All the above

Description : Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by ... in concrete increases the workability but also increases the liability to segregation (D) All the above

Last Answer : Answer: Option D

The maximum distance of the apex of a vertical curve of length L from the point of intersection of two grades + g1%, and - g2% (g1 > g2), is (A) L(g - g (B) L(g - g (C) L(g g (D) L(g - g

Description : The maximum distance of the apex of a vertical curve of length L from the point of intersection of two grades + g1%, and - g2% (g1 > g2), is (A) L(g - g (B) L(g - g (C) L(g g (D) L(g - g

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Adding 5% to 6% of moisture content by weight, increases the volume of dry sand from 18% to 38% (B) The bulking of fine sand is more than that of coarse sand (C) If the percentage content of moisture exceeds 10%, increase in bulk of sand starts increasing (D) All the above

Description : Pick up the correct statement from the following: (A) Adding 5% to 6% of moisture content by weight, increases the volume of dry sand from 18% to 38% (B) The bulking of fine sand is ... the percentage content of moisture exceeds 10%, increase in bulk of sand starts increasing (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following. The width of the right-of-way is decided so as to accommodate (A) Formation width (B) Side slopes (C) Horizontal curve (D) Vertical curve

Description : Pick up the incorrect statement from the following. The width of the right-of-way is decided so as to accommodate (A) Formation width (B) Side slopes (C) Horizontal curve (D) Vertical curve

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Forward pass is used for calculating earliest expected time (B) Backward pass is used for calculating the latest occurrence time (C) Maximum value of earliest expected time is used if there is more than one value of any event (D) All the above

Description : Pick up the correct statement from the following: (A) Forward pass is used for calculating earliest expected time (B) Backward pass is used for calculating the latest occurrence time (C) Maximum value of earliest ... time is used if there is more than one value of any event (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) A hydrograph is a plot of discharge versus time (B) A mass curve is a plot of accumulated flow versus time (C) The mass curve continuously rises (D) All the above

Description : Pick up the correct statement from the following:  (A) A hydrograph is a plot of discharge versus time  (B) A mass curve is a plot of accumulated flow versus time  (C) The mass curve continuously rises  (D) All the above 

Last Answer : (D) All the above 

Generally, first portion of a logistic curve for the population growth of a developing city, represents the growth of (A) Increasing (B) Decreasing (C) Constant (D) All the above

Description : Generally, first portion of a logistic curve for the population growth of a developing city,  represents the growth of  (A) Increasing  (B) Decreasing  (C) Constant  (D) All the above 

Last Answer : (A) Increasing

The side slope of formation in embankment is a) 2 : 1* b) 1: 1 c) 1:5 d) 1:3

Description : The side slope of formation in embankment is a) 2 : 1* b) 1: 1 c) 1:5 d) 1:3

Last Answer : a) 2 : 1*

Pick up the correct statement from the following: (A) O.M.C. refers to the moisture corresponding to the maximum point on the moisture content dry density curve (B) The line which shows moisture content dry density relation for soil containing a constant percentage of air voids, is known as air void line (C) The free fall of hammer for compaction is 30.5 cm (D) All the above

Description : Pick up the correct statement from the following: (A) O.M.C. refers to the moisture corresponding to the maximum point on the moisture content dry density curve (B) The line which shows moisture content dry ... void line (C) The free fall of hammer for compaction is 30.5 cm (D) All the above

Last Answer : (D) All the above

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is minimum(B) The pressure on the bottom of the wall is maximum (C) The pressure on the wall at the liquid level is zero, and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is maximum (B) ... and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Last Answer : Answer: Option C

Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point (C) Each ton of petroleum oil on distillation produces about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil

Description : Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches ... about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil

Last Answer : (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point

The catch water drains are provided in the a) Formation in the embankment b) Formation in cutting* c) Zero fills formation d) Steep gradient

Description : The catch water drains are provided in the a) Formation in the embankment b) Formation in cutting* c) Zero fills formation d) Steep gradient

Last Answer : b) Formation in cutting*

Draw conventional symbols for i) Compound wall ii) Pucca Building iii) Cutting iv) Embankment

Description : Draw conventional symbols for i) Compound wall ii) Pucca Building iii) Cutting iv) Embankment

Last Answer : i) Compound wall ii) Pucca Building iii) Cutting iv) Embankment

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

. In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with increasing Reynolds number (C) Point of maximum instability exists at a distance of 2r/3 from the pipe wall (r = pipe radius) (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Description : . In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with ... , shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Last Answer : (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

The effect of increasing pressure on the gaseous equilibrium of the reaction2X + 3Y ⇌ 3X + 2Y indicates that(A) Pressure has no effect(B) Backward reaction is favoured(C) Forward reaction is favoured(D) None of the

Description : The effect of increasing pressure on the gaseous equilibrium of the reaction2X + 3Y ⇌ 3X + 2Y indicates that (A) Pressure has no effect (B) Backward reaction is favoured (C) Forward reaction is favoured (D) None of the

Last Answer : (A) Pressure has no effect