While measuring with a metallic tape of 30 m length pull should be applied (A) 1 kg (B) 2 kg (C) 3 kg (D) 4 kg

While measuring with a metallic tape of 30 m length pull should be applied 

(A) 1 kg 

(B) 2 kg 

(C) 3 kg 

(D) 4 kg 

by

1 Answer

Answer :

(C) 3 kg

by

Related questions

A standard steel tape of length 30 m and cross-section 15 × 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of steel tape is 2.2 × 106 kg/cm2 , the correction to be applied is (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Description : If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Last Answer : (A) C = w²l3 /24F²

A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag correction is (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Description : A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag  correction is  (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Last Answer : (A) l3W²/24P²

A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance of 40 kg per tonne, then the drawbar pull of the tractor will (A) Reduce by 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Description : A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance ... 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Last Answer : (A) Reduce by 200 kg

If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Last Answer : (B) 250 kg

The maximum rimpull in the first gear of a tractor while towing a load is 6300 kg. The tractor weighs 12.5 tonnes and is operating along a 2 percent upgrade and the rolling resistance is 45 kg/tonne. Pull available for towing the load is (A) 3425 kg (B) 5515 kg (C) 4350 kg (D) 2975 kg

Description : The maximum rimpull in the first gear of a tractor while towing a load is 6300 kg. The tractor weighs 12.5 tonnes and is operating along a 2 percent upgrade and the rolling resistance is 45 kg/tonne. Pull available for towing the load is (A) 3425 kg (B) 5515 kg (C) 4350 kg (D) 2975 kg

Last Answer : (B) 5515 kg

In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal a.the force applied on A must be equal to that on B b.at least one man on side B should be removed c.infinite force will be required to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Description : In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal ... to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Last Answer : c. infinite force will be required to be applied at both ends

Short offsets are measured with (A) An ordinary chain(B) An invar tape (C) A metallic tape (D) A steel tape

Description : Short offsets are measured with (A) An ordinary chain (B) An invar tape (C) A metallic tape (D) A steel tape

Last Answer : (A) An ordinary chain

The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly (A) 0.043 m (B) 0.053 m (C) 0.063 m (D) 0.083 m

Description : The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly  (A) 0.043 m  (B) 0.053 m  (C) 0.063 m  (D) 0.083 m 

Last Answer : (D) 0.083 m 

The magnitude of ‘sag correction’ during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run (c) Square of the weight of the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Description : The magnitude of sag correction' during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run ... the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Last Answer : (c) Square of the weight of the tape, in kg per m run

The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Description : The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Last Answer : Answer: Option C

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

Measuring with a 30 m chain, 0.01 m too short, introduces (A) Positive compensating error (B) Negative compensating error (C) Positive cumulative error (D) Negative cumulative error

Description : Measuring with a 30 m chain, 0.01 m too short, introduces (A) Positive compensating error (B) Negative compensating error (C) Positive cumulative error (D) Negative cumulative error

Last Answer : (C) Positive cumulative error

Two bodies of mass 6 kg and 9 kg are connected with a light inextensile string passing over a smooth pulley with one of the bodies on a smooth inclined plane (θ = 30°) and the other hanging freely from the other end. Show that the time taken by 9 kg to pull 6 kg up the entire length is half the time taken by 6 kg to pull 9 kg over the same plane.

Description : Two bodies of mass 6 kg and 9 kg are connected with a light inextensile string passing over a smooth pulley with one of the bodies on a smooth inclined plane (θ = 30°) and the other hanging freely from the ... kg up the entire length is half the time taken by 6 kg to pull 9 kg over the same plane.

Last Answer : Given: Mass of body A (mA) = 6 kg Mass of body B (mB) = 9 kg Angle of inclination of the plane (θ) = 30° Let's assume that the acceleration of body A (aA) and body B (aB) are in opposite ... we know that the time taken (t) is given by the formula: t = √(2d/a), where d is the distance travelled

While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Description : While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of ... true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Last Answer : (B) 0.15 cm

While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Description : While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Last Answer : (C) 20 (sec - 1)

A man wished to move a block of size 3 m x 3 m weighing 80 kg. The coefficient of friction between the block and the ground is 0.27. Which of the following methods should be used? a.Slide along the ground by pushing b.Ask for cranes c.Pull it d.Tip it over e.Lift it bodily

Description : A man wished to move a block of size 3 m x 3 m weighing 80 kg. The coefficient of friction between the block and the ground is 0.27. Which of the following methods should be used? a.Slide along the ground by pushing b.Ask for cranes c.Pull it d.Tip it over e.Lift it bodily

Last Answer : d. Tip it over

A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Description : A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Last Answer : (B) 0.2275 mm

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

A metallic tape is made of (a) Steel (b) Invar (c) Linen (d) Cloth & wires*

Description : A metallic tape is made of (a) Steel (b) Invar (c) Linen (d) Cloth & wires*

Last Answer : (d) Cloth & wires

If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Description : If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D

Last Answer : (D) 59 D

A metallic wire of length 1 m is stretched to duble its length. Calculate the ratio of its initial and final resistances assuming that there is no cha

Description : A metallic wire of length 1 m is stretched to duble its length. Calculate the ratio of its initial and final resistances assuming that there is no cha

Last Answer : A metallic wire of length 1 m is stretched to duble its length. Calculate the ratio of its ... there is no change in its density on stretching.

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

The resultant of the following three couples 20 kg force, 0.5 m arm, +ve sense 30 kg force, 1 m arm, -ve sense 40 kg force, 0.25 m arm, +ve sense having arm of 0.5 m will be (A) 20 kg, -ve sense (B) 20 kg, +ve sense (C) 10 kg, +ve sense (D) 10 kg, -ve sense

Description : The resultant of the following three couples 20 kg force, 0.5 m arm, +ve sense 30 kg force, 1 m  arm, -ve sense 40 kg force, 0.25 m arm, +ve sense having arm of 0.5 m will be  (A) 20 kg, -ve sense  (B) 20 kg, +ve sense  (C) 10 kg, +ve sense  (D) 10 kg, -ve sense 

Last Answer : (A) 20 kg, -ve sense

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is (A) 28 liters (B) 30 liters (C) 32 liters (D) 34 liters

Description : Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is (A) 28 liters (B) 30 liters (C) 32 liters (D) 34 liters

Last Answer : Answer: Option C

A body of weight 100 kg is placed on a horizontal plane. A horizontal force of 30 kg is applied and the block is just on the point of motion. The angle of friction is a.About 16? b.30? c.45? d.60? e.None of the above

Description : A body of weight 100 kg is placed on a horizontal plane. A horizontal force of 30 kg is applied and the block is just on the point of motion. The angle of friction is a.About 16? b.30? c.45? d.60? e.None of the above

Last Answer : a. About 16?

A glass tube of smaller diameter is used while performing an experiment for the capillary rise of water because (A) It is easier to see through the glass tube (B) Glass tube is cheaper than a metallic tube (C) It is not possible to conduct this experiment with any other tube (D) All of the above

Description : A glass tube of smaller diameter is used while performing an experiment for the capillary rise of water because (A) It is easier to see through the glass tube (B) Glass tube is cheaper than a metallic ... (C) It is not possible to conduct this experiment with any other tube (D) All of the above

Last Answer : Answer: Option A

Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Description : Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Last Answer : vernier callipers

Should I wear the bright green, metallic nail polish I just applied to my nails to the job interview I have scheduled for Friday?

Description : Should I wear the bright green, metallic nail polish I just applied to my nails to the job interview I have scheduled for Friday?

Last Answer : Absolutely don’t wear it. Allow your jewelry to be the interesting stuff, not your nails. It sounds silly but I’ve seen it happen—bright, crazy nail polish gives the impression that you’re wacky, whereas interesting, even exciting jewelry says something totally different.

A cross a metallic conductor of non-uniform cross-section, a constant potential difference is applied. The quantity which remain (s) constant along th

Description : A cross a metallic conductor of non-uniform cross-section, a constant potential difference is applied. The quantity which remain (s) constant along th

Last Answer : A cross a metallic conductor of non-uniform cross-section, a constant potential difference is applied ... current C. drift velocity D. electric field

The deflection of a uniform circular bar of diameter d and length , which extends by an amount under a tensile pull , when it carries the same load at its mid-span, is (A) el/2d (B) e²l/3d² (C) el²/3d² (D) e²l²/3d

Description : The deflection of a uniform circular bar of diameter d and length , which extends by an  amount under a tensile pull , when it carries the same load at its mid-span, is  (A) el/2d (B) e²l/3d² (C) el²/3d² (D) e²l²/3d

Last Answer : (C) el²/3d

Three measuring rods are 64 cm,80 cm and 96 cm in length . What is the least length of cloth that can can be measured exact number of times using any one of these rods? (a) 9.60 m (b) 8 m (c) 9.60 cm (d) 96 m

Description : Three measuring rods are 64 cm,80 cm and 96 cm in length . What is the least length of cloth that can can be measured exact number of times using any one of these rods? (a) 9.60 m (b) 8 m (c) 9.60 cm (d) 96 m

Last Answer : Ans 4. 9.60 m

Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the heatcapacity of the substance in the molten state(C) There is an increase in entropy, when a spontaneous change occurs in anisolated system(D) At absolute zero temperature, the heat capacity for many pure crystallinesubstances is zero

Description : Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the ... isolated system (D) At absolute zero temperature, the heat capacity for many pure crystalline substances is zero

Last Answer : (C) There is an increase in entropy, when a spontaneous change occurs in an isolated system

A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. Specific heat of block material is 0.4 kJ.kg-1. K-1. Ignoring the effect of expansion and contraction and also the heat capacity to tank, the total entropy change in kJ.kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Description : A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. ... .kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Last Answer : (B) 0

In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per 30 metre tape duly corrected for temperature, slope and sag, the angular error of closure not to exceed (where n is the number of traverse legs) (A) 50" n(B) 30" n(C) 60" n (D) None of these

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

A ball bounces higher at high altitudes than in plains. This is because (a) the pressure on higher altitudes is lower than that in plains (b) Downward pull due to gravity is less at higher altitudes (c) The rarefied air offers less resistance to the ball (d) You become more energetic at hills, so greater the force applied, higher goes the ball.

Description : A ball bounces higher at high altitudes than in plains. This is because (a) the pressure on higher altitudes is lower than that in plains (b) Downward pull due to gravity is less at higher altitudes ... ball (d) You become more energetic at hills, so greater the force applied, higher goes the ball.

Last Answer : Ans:(a)

If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Description : If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Last Answer : (C) 1/20,000

While measuring a chain line between two stations and intervened by a raised ground (A) Vision gets obstructed (B) Chaining gets obstructed (C) Both vision and chaining get obstructed (D) All the above

Description : While measuring a chain line between two stations and intervened by a raised ground (A) Vision gets obstructed (B) Chaining gets obstructed (C) Both vision and chaining get obstructed (D) All the above

Last Answer : (A) Vision gets obstructed

It is more difficult to obtain good results while measuring horizontal distance by stepping (A) Up-hill (B) Down-hill (C) In low undulations (D) In plane areas

Description : It is more difficult to obtain good results while measuring horizontal distance by stepping (A) Up-hill (B) Down-hill (C) In low undulations (D) In plane areas

Last Answer : (A) Up-hill

The slope correction for a length of 30 m along a gradient of 1 in 20, is (A) 3.75 cm (B) 0.375 cm (C) 37.5 cm (D) 2.75 cm

Description : The slope correction for a length of 30 m along a gradient of 1 in 20, is  (A) 3.75 cm  (B) 0.375 cm  (C) 37.5 cm  (D) 2.75 cm

Last Answer : (A) 3.75 cm 

If the radius of a simple curve is 600 m, the maximum length of the chord for calculating offsets, is taken (A) 15 m (B) 20 m (C) 25 m (D) 30 m

Description : If the radius of a simple curve is 600 m, the maximum length of the chord for calculating offsets, is  taken  (A) 15 m  (B) 20 m  (C) 25 m  (D) 30 m

Last Answer : (D) 30 m