A pressure conduit carrying water beneath a stream or a canal, is known as (A) Sag (B) Depressed pipe (C) Inverted syphon (D) All the above

A pressure conduit carrying water beneath a stream or a canal, is known as 

(A) Sag 

(B) Depressed pipe 

(C) Inverted syphon 

(D) All the above 

by

1 Answer

Answer :

(D) All the above 

by

Related questions

The arrangement made for passing the sewer line below an obstruction below the hydraulic gradient lines called A. Inverted syphon B. Depressed sewer C. Sag pipe D. all of these

Description : The arrangement made for passing the sewer line below an obstruction below the hydraulic gradient lines called A. Inverted syphon B. Depressed sewer C. Sag pipe D. all of these

Last Answer : ANS: D

How do you trace an (empty and probably pvc) conduit pipe beneath a parking lot?

Description : How do you trace an (empty and probably pvc) conduit pipe beneath a parking lot?

Last Answer : If you have access, you can fill the pipe with water, run a current through it, and track it with a wire tracer

The drainage water intercepting the canal can be disposed of by passing the canal below the drainage in (A) Aqueduct and syphon aqueduct (B) Aqueduct and super passage (C) Super passage and canal syphon (D) Level crossing

Description : The drainage water intercepting the canal can be disposed of by passing the canal below the drainage in (A) Aqueduct and syphon aqueduct (B) Aqueduct and super passage (C) Super passage and canal syphon (D) Level crossing

Last Answer : Answer: Option C

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

Explain with sketch working of syphon pipe

Description : Explain with sketch working of syphon pipe

Last Answer : i. Syphon is long bent pipe which is used to transfer the liquid from reservoir at a higher level to another reservoir at a lower level , When two reservoirs are separated by a hill or ... is less than atmospheric pressure or negative pressure to rise the liquid or water in the inlet limb.

In which of the following cases, it is possible for flow to occur from low pressure to high pressure? (A) Flow of liquid upward in a vertical pipe (B) Flow through a converging section (C) Flow of air downward in a pipe (D) Impossible in a constant cross-section conduit

Description : In which of the following cases, it is possible for flow to occur from low pressure to high pressure? (A) Flow of liquid upward in a vertical pipe (B) Flow through a converging section (C) Flow of air downward in a pipe (D) Impossible in a constant cross-section conduit

Last Answer : (B) Flow through a converging section

If span is 150 mts and sag is 10 ft of a cable carrying a load of 3200 kg per horizontal metre then tension of ends is a.104,000 kg b.107 dynes c.1200,000 kg d.932,000 kg e.584,000 kg

Description : If span is 150 mts and sag is 10 ft of a cable carrying a load of 3200 kg per horizontal metre then tension of ends is a.104,000 kg b.107 dynes c.1200,000 kg d.932,000 kg e.584,000 kg

Last Answer : d. 932,000 kg

A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Description : A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Last Answer : Answer: B

A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Description : A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Last Answer : Answer: C

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

Can a PVC pipe be used for electrical conduit?

Description : Can a PVC pipe be used for electrical conduit?

Last Answer : Why not, the Plumbing PVC actually has more testing to meet plumbing standards than PVC conduit. Both are made of the same material, so yes it can.

What is the difference between conduit and pipe?

Description : What is the difference between conduit and pipe?

Last Answer : Tube and pipe are both used for conveying liquids or gases under pressure. They differ in how they are sized and their rigidity. A conduit is mainly used to protect and route electrical wiring.

A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends

Description : A pressure conduit laid underground, may not be subjected to  (A) Internal pressure of water  (B) Pressure due to external load  (C) Longitudinal temperature stress  (D) Longitudinal stresses due to unbalanced pressure to bends 

Last Answer : (C) Longitudinal temperature stress 

The force which develops in a pressure conduit supported on trestles, is (A) Tension (B) Compression (C) Temperature stress (D) Flexural stress

Description : The force which develops in a pressure conduit supported on trestles, is  (A) Tension  (B) Compression  (C) Temperature stress  (D) Flexural stress

Last Answer : (D) Flexural stress

Pick up the correct statement from the following regarding the pressure conduits: (A) Pressure conduits are permitted to run ¾th full (B) Pressure conduits are always laid along down grades (C) The hydraulic gradient line always coincides the invert of the conduit (D) None of these

Description : Pick up the correct statement from the following regarding the pressure conduits:  (A) Pressure conduits are permitted to run ¾th full  (B) Pressure conduits are always laid along down grades  ... ) The hydraulic gradient line always coincides the invert of the conduit  (D) None of these

Last Answer : (D) None of these

Pickup the incorrect statement from the following: (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line (B) The pressure conduits may be taken uphill upto a maximum height of 8.3 m (C) Aqueducts and tunnels sections are generally kept circular (D) None of these

Description : Pickup the incorrect statement from the following:  (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line  (B) The pressure conduits may be taken uphill ... m  (C) Aqueducts and tunnels sections are generally kept circular  (D) None of these 

Last Answer : (D) None of these 

When an up gradient of a highway meets a downgrade, the vertical curve provided, is known as (A) Valley curve (B) Sag curve (C) Summit curve (D) All the above

Description : When an up gradient of a highway meets a downgrade, the vertical curve provided, is known as (A) Valley curve (B) Sag curve (C) Summit curve (D) All the above

Last Answer : Answer: Option C

Corrosion of a pipe (A) Reduces its life span (B) Reduces its carrying capacity (C) Adds colour to water (D) All the above

Description : Corrosion of a pipe (A) Reduces its life span (B) Reduces its carrying capacity (C) Adds colour to water (D) All the above

Last Answer : (D) All the above

An inverted siphon is designed generally for A. One pipe B. Two pipes C. Three pipes D. Four pipes

Description : An inverted siphon is designed generally for A. One pipe B. Two pipes C. Three pipes D. Four pipes

Last Answer : ANS: C

For sewers, inverted siphon is provided for A. One pipe B. Two pipes C. Three pipes D. Four pipes

Description : For sewers, inverted siphon is provided for A. One pipe B. Two pipes C. Three pipes D. Four pipes

Last Answer : ANS: C

State two uses of syphon.

Description : State two uses of syphon.

Last Answer : i. To take out water from one reservoir to another reservoir separated by a hill or ridge. ii. To drain out water from a channel without any outlet. iii. To take out the water from a tank not having any outlet.

Contact pressure beneath a rigid footing resting on cohesive soil is (A) Less at edges compared to middle (B) More at edges compared to middle (C) Uniform throughout (D) None of the above

Description : Contact pressure beneath a rigid footing resting on cohesive soil is (A) Less at edges compared to middle (B) More at edges compared to middle (C) Uniform throughout (D) None of the above

Last Answer : Answer: Option B

If the contacts of a motor starter or controller fail to drop out when the 'stop' button is depressed the ____________. A. contacts are carrying excessive current B. contacts have become welded together C. shading coil is broken D. shading coil is loose

Description : If the contacts of a motor starter or controller fail to drop out when the 'stop' button is depressed the ____________. A. contacts are carrying excessive current B. contacts have become welded together C. shading coil is broken D. shading coil is loose

Last Answer : Answer: B

Disc compensators are provided in large diameter fuel gas carrying pipelines to (A) Keep the pipe in proper orientation (B) Make the pipe joint leak-proof (C) Account for contraction/expansion of pipe due to temperature changes of the surroundings (D) Account for the pressure variation side the pipeline

Description : Disc compensators are provided in large diameter fuel gas carrying pipelines to (A) Keep the pipe in proper orientation (B) Make the pipe joint leak-proof (C) Account for contraction/expansion ... due to temperature changes of the surroundings (D) Account for the pressure variation side the pipeline

Last Answer : (C) Account for contraction/expansion of pipe due to temperature changes of the surroundings

The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly (A) 0.043 m (B) 0.053 m (C) 0.063 m (D) 0.083 m

Description : The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly  (A) 0.043 m  (B) 0.053 m  (C) 0.063 m  (D) 0.083 m 

Last Answer : (D) 0.083 m 

A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag correction is (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Description : A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag  correction is  (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Last Answer : (A) l3W²/24P²

Which one of the following mistakes/errors may be cumulative + or - : (A) Bad ranging (B) Bad straightening (C) Erroneous length of chain (D) Sag

Description : Which one of the following mistakes/errors may be cumulative + or - :  (A) Bad ranging  (B) Bad straightening  (C) Erroneous length of chain  (D) Sag

Last Answer : (C) Erroneous length of chain

If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Description : If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Last Answer : (A) C = w²l3 /24F²

In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per 30 metre tape duly corrected for temperature, slope and sag, the angular error of closure not to exceed (where n is the number of traverse legs) (A) 50" n(B) 30" n(C) 60" n (D) None of these

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

The magnitude of ‘sag correction’ during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run (c) Square of the weight of the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Description : The magnitude of sag correction' during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run ... the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Last Answer : (c) Square of the weight of the tape, in kg per m run

The maximum V belt sag when applying finger pressure is a) 10 mm b) 12 mm c) 15 mm d) 17 mm

Description : The maximum V belt sag when applying finger pressure is a) 10 mm b) 12 mm c) 15 mm d) 17 mm

Last Answer : c) 15 mm

Mass velocity in case of steady flow and through a constant cross￾section conduit is independent of the (A) Temperature (B) Pressure (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Mass velocity in case of steady flow and through a constant cross￾section conduit is independent of the (A) Temperature (B) Pressure (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A back sight (A) Is always taken on a point of known elevation or can be computed (B) Is added to the known level to obtain the instrument height (C) Taken on an inverted staff is treated as negative (D) All the above

Description : A back sight  (A) Is always taken on a point of known elevation or can be computed  (B) Is added to the known level to obtain the instrument height  (C) Taken on an inverted staff is treated as negative  (D) All the above 

Last Answer : (D) All the above 

Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Description : Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Last Answer : (C) No change

In case of staged packed bed reactors carrying out exothermic reaction, use (A) High recycle for pure gas (B) Plug flow for dilute liquid requiring no large preheating of feed (C) Cold shot operations for a dilute solution requiring large preheating to bring the stream upto the reaction temperature (D) All (A), (B) and (C)

Description : In case of staged packed bed reactors carrying out exothermic reaction, use (A) High recycle for pure gas (B) Plug flow for dilute liquid requiring no large preheating of feed (C) Cold shot operations for a ... preheating to bring the stream upto the reaction temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Consider the following statements regarding the satellite imaging: 1. The satellite orbit is fixed in the inertial space 2. During successive across-track imaging, the earth rotates beneath the sensor 3. The satellite images a skewed area Which one of the following statements is/are correct? (A) 1, 2, 3 (B) 1, 3 (C) 2, 3 (D) 1, 2

Description : Consider the following statements regarding the satellite imaging: 1. The satellite orbit is fixed in the inertial space 2. During successive across-track imaging, the earth rotates beneath the sensor 3. The satellite images a skewed area ... ? (A) 1, 2, 3 (B) 1, 3 (C) 2, 3 (D) 1, 2

Last Answer : Answer: Option A

In a depressed nappe (A) The pressure below the nappe is atmospheric (B) The pressure below the nappe is negative (C) The pressure above the nappe is atmospheric (D) The pressure above the nappe is negative

Description : In a depressed nappe (A) The pressure below the nappe is atmospheric (B) The pressure below the nappe is negative (C) The pressure above the nappe is atmospheric (D) The pressure above the nappe is negative

Last Answer : Answer: Option B

When a cylindrical vessel, containing some liquid, is rotated about its vertical axis, the liquid surface is depressed down at the axis of its rotation and rises up near the walls of the vessel on all sides. This type of flow is known as (A) Steady flow (B) Turbulent flow (C) Vortex flow

Description : When a cylindrical vessel, containing some liquid, is rotated about its vertical axis, the liquid surface is depressed down at the axis of its rotation and rises up near the walls of the vessel on all sides. This type of flow is known as (A) Steady flow (B) Turbulent flow (C) Vortex flow

Last Answer : Answer: Option C

The maximum pressure to which a pipe is subjected to during its operation, is known (A) Working pressure (B) Design pressure (C) Test pressure (D) Pipe pressure

Description : The maximum pressure to which a pipe is subjected to during its operation, is known  (A) Working pressure  (B) Design pressure  (C) Test pressure  (D) Pipe pressure 

Last Answer : (A) Working pressure 

During ageing of fluid carrying pipes, the (A) Pipe becomes smoother with use (B) Friction factor increases linearly with time (C) Absolute roughness decreases with time (D) Absolute roughness increases linearly with time

Description : During ageing of fluid carrying pipes, the (A) Pipe becomes smoother with use (B) Friction factor increases linearly with time (C) Absolute roughness decreases with time (D) Absolute roughness increases linearly with time

Last Answer : (D) Absolute roughness increases linearly with time

Identification of pipelines carrying different liquids and gases is done by the __________ of the pipe(A) Diameter(B) Colour(C) Altitude(D) None of these.

Description : Identification of pipelines carrying different liquids and gases is done by the __________ of the pipe. (A) Diameter (B) Colour (C) Altitude (D) None of these

Last Answer : (B) Colour

_________ pipe is the most suitable for carrying sanitary drainage. (A) Stainless steel (B) Reinforced cement concrete (C) Cast iron (D) Asbestos cement

Description : _________ pipe is the most suitable for carrying sanitary drainage. (A) Stainless steel (B) Reinforced cement concrete (C) Cast iron (D) Asbestos cement

Last Answer : C) Cast iron

Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Description : Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans? (A) Emissivity of pipe surface (B) Diameter & length of the pipe (C) Temperature of hot pipe surface & that of air in the room (D) None of thes

Last Answer : Option D

The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is (A) 3.290 m (B) 3.300 m (C) 3.275 m (D) 2.790 m

Description : The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is (A) 3.290 m (B) 3.300 m (C) 3.275 m (D) 2.790 m

Last Answer : (B) 3.300 m

Accurate measurement of deflection angles with a transit not properly adjusted may be made by (A) Setting the Vernier A at zero at back station and then plunging the telescope (B) Setting the Vernier A at zero at back station and turning the instrument to the forward station (C) Taking two back sights one with the telescope normal and the other with telescope inverted (D) None of these

Description : Accurate measurement of deflection angles with a transit not properly adjusted may be made by (A) Setting the Vernier A at zero at back station and then plunging the telescope (B) Setting the ... back sights one with the telescope normal and the other with telescope inverted (D) None of these

Last Answer : (C) Taking two back sights one with the telescope normal and the other with telescope inverted

The type of butt joints in common use, is: (A) Single inverted V-butt joint (B) Double V-butt joint (C) Double U-butt joint (D) Single V-butt joint

Description : The type of butt joints in common use, is: (A) Single inverted V-butt joint (B) Double V-butt joint (C) Double U-butt joint (D) Single V-butt joint

Last Answer : (A) Single inverted V-butt joint

R.L. of floor at a building is 74.4 m, staff reading on the floor is 1.625 and staff reading when it is held inverted with bottom touching the ceiling of a hall is 2.870; then the height of the ceiling above the floor is (a) 3.593 m (b) 3.953 m (c) 4.495 m (d) 4. 594 m

Description : R.L. of floor at a building is 74.4 m, staff reading on the floor is 1.625 and staff reading when it is held inverted with bottom touching the ceiling of a hall is 2.870; then the height of the ceiling above the floor is (a) 3.593 m (b) 3.953 m (c) 4.495 m (d) 4. 594 m

Last Answer : (c) 4.495 m