The maximum pressure to which a pipe is subjected to during its operation, is known (A) Working pressure (B) Design pressure (C) Test pressure (D) Pipe pressure

The maximum pressure to which a pipe is subjected to during its operation, is known 

(A) Working pressure 

(B) Design pressure 

(C) Test pressure 

(D) Pipe pressure 

by

1 Answer

Answer :

(A) Working pressure 

by

Related questions

The maximum pressure which the pipe can withstand without any leakage during hydrostatic pressure test, is called (A) Working pressure (B) Design pressure (C) Test pressure (D) Hydrostatic pressure

Description : The maximum pressure which the pipe can withstand without any leakage during hydrostatic pressure test, is called (A) Working pressure (B) Design pressure (C) Test pressure (D) Hydrostatic pressure

Last Answer : (C) Test pressure

Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct shear test (C) The confining pressure is maximum during an unconfined compression test (D) The cylindrical specimen of a soil is subjected to major principal stress till it fails due to shearing along the plane of the failure

Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure

Last Answer : Option A

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

Large diameter sewers subjected to external pressure alone, are reinforced A. Near the inner surface of the pipe B. Near the outer surface of the pipe C. Both A. and B. D. With elliptical cage

Description : Large diameter sewers subjected to external pressure alone, are reinforced A. Near the inner surface of the pipe B. Near the outer surface of the pipe C. Both A. and B. D. With elliptical cage

Last Answer : ANS: D

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is minimum(B) The pressure on the bottom of the wall is maximum (C) The pressure on the wall at the liquid level is zero, and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. Which of the following statement is correct? (A) The pressure on the wall at the liquid level is maximum (B) ... and on the bottom of the wall is maximum (D) The pressure on the bottom of the wall is zero

Last Answer : Answer: Option C

The maximum pressure to which cast iron pipes may be subjected to, is (A) 3 kg/cm2 (B) 5 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm

Description : The maximum pressure to which cast iron pipes may be subjected to, is  (A) 3 kg/cm2 (B) 5 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm

Last Answer : (C) 7 kg/cm

Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the maximum to which the clay has ever been subjected, it is called normally consolidated clay (C) If the present effective stress in the past was more than present effective stress, it is called over-consolidated clay (D) All the above

Description : Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the ... more than present effective stress, it is called over-consolidated clay (D) All the above

Last Answer : Answer: Option D

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

In basins subjected to strong winds and tide, the length of the berthing area should not be less than (A) The length of design vessel (B) The length of design vessel + 10% clearance between adjacent vessels (C) The length of design vessel + 20% clearance between adjacent vessels (D) Twice the length of design vessel

Description : In basins subjected to strong winds and tide, the length of the berthing area should not be less than (A) The length of design vessel (B) The length of design vessel + 10% clearance ... The length of design vessel + 20% clearance between adjacent vessels (D) Twice the length of design vessel

Last Answer : (C) The length of design vessel + 20% clearance between adjacent vessels

Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?(A) Check plates(B) Jaw plates(C) Toggles(D) Crush shaft

Description : Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation? (A) Check plates (B) Jaw plates (C) Toggles (D) Crush shaft

Last Answer : (B) Jaw plates

01. Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, at right angles to the direction of flow of the liquid is known as lift. A) True B) False

Description : 01. Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, at right angles to the direction of flow of the liquid is known as lift. A) True B) False

Last Answer : A

Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Description : Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Last Answer : Answer: Option B

At the center line of a pipe flowing under pressure where the velocity gradient is zero, the shear stress will be (A) Minimum (B) Maximum (C) Zero (D) Could be any value

Description : At the center line of a pipe flowing under pressure where the velocity gradient is zero, the shear stress will be (A) Minimum (B) Maximum (C) Zero (D) Could be any value

Last Answer : Answer: Option D

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2

Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of  moment M at its centre. The maximum bending moment in the beam is  (A) M (B) M/2  (C) M/3  (D) ML/2 

Last Answer : (A) M

In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Description : In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Last Answer : (B) At the built-in upper cross-section

A pressure conduit carrying water beneath a stream or a canal, is known as (A) Sag (B) Depressed pipe (C) Inverted syphon (D) All the above

Description : A pressure conduit carrying water beneath a stream or a canal, is known as  (A) Sag  (B) Depressed pipe  (C) Inverted syphon  (D) All the above 

Last Answer : (D) All the above 

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts(C) No shear stress acts (D) None of these

Description : Along the principal plan subjected to maximum principal stress (A) Maximum shear stress acts (B) Minimum shear stress acts (C) No shear stress acts (D) None of these

Last Answer : (C) No shear stress acts

If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced in the shaft, is (A) Zero (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Description : A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced  in the shaft, is  (A) Zero  (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Last Answer : (B) 16T/ 3

The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3

Description : The maximum load to which a fillet joint of length can be subjected to, is  (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3 

Last Answer : (A) 0.7 × S × fillet size × L

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be three times the maximum tensile stress, centre of gravity of the section from flange side is (A) h/4 (B) h/3 (C) h/2 (D) 2/3 h

Description : A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be  three times the maximum tensile stress, centre of gravity of the section from flange side is  (A) h/4  (B) h/3  (C) h/2  (D) 2/3 h

Last Answer : (A) h/4 

If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Description : If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Last Answer : Answer: Option D Answer: Option D

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

A clay subjected to pressure in excess to its present over-burden, is said to be (A) Pre-compressed (B) Pre-consolidated (C) Over-consolidated (D) All the above

Description : A clay subjected to pressure in excess to its present over-burden, is said to be (A) Pre-compressed (B) Pre-consolidated (C) Over-consolidated (D) All the above

Last Answer : Answer: Option D

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall per unit length is (where w = Specific weight of liquid, and H = Height of liquid) (A) wH (B) wH/2 (C) wH2 /2 (D) wH2 /3

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall per unit length is (where w = Specific weight of liquid, and H = Height of liquid) (A) wH (B) wH/2 (C) wH2 /2 (D) wH2 /3

Last Answer : Answer: Option C

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall acts at a distance __________ from the liquid surface. (A) H/3 (B) H/2 (C) 2H/3 (D) 3H/4

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall acts at a distance __________ from the liquid surface. (A) H/3 (B) H/2 (C) 2H/3 (D) 3H/4

Last Answer : Answer: Option C

Consider the following statements: 1. Standard penetration test is commonly used for cohesionless soils. 2. Standard penetration test results in respect of a cohesionless soil are correlated to its density index and friction angle. 3. Use of H-value not corrected for overburden pressure leads to highly conservative design of footings at shallow depths. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. Standard penetration test is commonly used for cohesionless soils. 2. Standard penetration test results in respect of a cohesionless soil are correlated to its density index and friction angle. 3. Use of H- ... 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (a) 1, 2 & 3

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

Pick up the incorrect statement from the following: (A) Free surface ground water is subjected to atmospheric pressure (B) Water table surface rises and falls with seasons (C) Depth of water table is directly proportional to the rate of drawl of water (D) Level of water table remains stationary

Description : Pick up the incorrect statement from the following:  (A) Free surface ground water is subjected to atmospheric pressure  (B) Water table surface rises and falls with seasons  (C) ... directly proportional to the rate of drawl of water  (D) Level of water table remains stationary 

Last Answer : (D) Level of water table remains stationary 

The gaseous form of chlorine gets converted into liquid form when subjected to a pressure of (A) 5 kg/cm2 (B) 6 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm

Description : The gaseous form of chlorine gets converted into liquid form when subjected to a pressure of  (A) 5 kg/cm2 (B) 6 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm

Last Answer : (C) 7 kg/cm

A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends

Description : A pressure conduit laid underground, may not be subjected to  (A) Internal pressure of water  (B) Pressure due to external load  (C) Longitudinal temperature stress  (D) Longitudinal stresses due to unbalanced pressure to bends 

Last Answer : (C) Longitudinal temperature stress 

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Last Answer : (A) Zero

When a vertical wall is subjected to pressures due to liquid on both sides, the resultant pressure is the __________ of the two pressures. (A) Sum (B) Difference (C) Arithmetic mean (D) Geometric mean

Description : When a vertical wall is subjected to pressures due to liquid on both sides, the resultant pressure is the __________ of the two pressures. (A) Sum (B) Difference (C) Arithmetic mean (D) Geometric mean

Last Answer : Answer: Option B

The center of pressure of a surface subjected to fluid pressure is the point (A) On the surface at which resultant pressure acts (B) On the surface at which gravitational force acts (C) At which all hydraulic forces meet (D) Similar to metacentre

Description : The center of pressure of a surface subjected to fluid pressure is the point (A) On the surface at which resultant pressure acts (B) On the surface at which gravitational force acts (C) At which all hydraulic forces meet (D) Similar to metacentre

Last Answer : Answer: Option A

When a plate is immersed in a liquid parallel to the flow, it will be subjected to a pressure __________ that if the same plate is immersed perpendicular to the flow. (A) Less than (B) More than (C) Equal to (D) None of these

Description : When a plate is immersed in a liquid parallel to the flow, it will be subjected to a pressure __________ that if the same plate is immersed perpendicular to the flow. (A) Less than (B) More than (C) Equal to (D) None of these

Last Answer : Answer: Option A

Due to the impact of water wave on a sea shore structure (A) Hydrostatic pressure coupled with a strong momentary impact is caused (B) Vibrations are subjected (C) Internal pressure is developed (D) All of the above

Description : Due to the impact of water wave on a sea shore structure (A) Hydrostatic pressure coupled with a strong momentary impact is caused (B) Vibrations are subjected (C) Internal pressure is developed (D) All of the above

Last Answer : (D) All of the above

Whitworth compressed steel is obtained when molten steel is subjected to a pressure of (A) 5 kg/mm2 (B) 9 kg/mm2 (C) 13 kg/mm2 (D) 15 kg/mm

Description : Whitworth compressed steel is obtained when molten steel is subjected to a pressure of (A) 5 kg/mm2 (B) 9 kg/mm2 (C) 13 kg/mm2 (D) 15 kg/mm

Last Answer : Answer: Option B