The following gas phase reactions are carried out isothermally in a CSTR. A → 2R ; r1 = k1pA ; k1 = 20mole/(sec.m3 bar)A → 3S ; r2 = k2 pA ;k2 = 40mole/(sec.m3.bar)What is the maximum possible value of FR(mole/sec.)?(A) 1/3(B) 1/2(C) 2/3(D) 2

The following gas phase reactions are carried out isothermally in a
CSTR.
A → 2R ; r1 = k1pA ;
k1 = 20mole/(sec.m3 bar)
A → 3S ; r2 = k2 pA ;
k2 = 40mole/(sec.m3
.bar)
What is the maximum possible value of FR(mole/sec.)?
(A) 1/3
(B) 1/2
(C) 2/3
(D) 2
by

1 Answer

Answer :

(C) 2/3
by

Related questions

The first order gas phase reaction as shown in the bellow figure is conducted isothermally in batch mode. The rate of change of conversion with time is given by (A) dXA /dt = k1 (1 - XA ) 2 (1 + 2XA ) (B) dXA /dt = k1 (1 - XA ) (1 + 0.5XA ) (C) dXA /dt = k1 (1 - XA ) (D) dXA /dt = k1 (1 - XA )/(1 + XA )

Description : The first order gas phase reaction as shown in the bellow figure is conducted isothermally in batch mode. The rate of change of conversion with time is given by (A) dXA /dt = k1 (1 - XA ) 2 (1 + 2XA ) (B) dXA /dt = k1 (1 - XA ... 5XA ) (C) dXA /dt = k1 (1 - XA ) (D) dXA /dt = k1 (1 - XA )/(1 + XA )

Last Answer : (C) dXA /dt = k1 (1 - XA

With increase in K2 /K1 in case of a unimolecular type elementary reactions as shown in the bellow figure, the fractional yield of 'R' in mixed reactor (for a given conversion of 'A'). (A) Decreases (B) Increases (C) Increases linearly (D) Remain same

Description : With increase in K2 /K1 in case of a unimolecular type elementary reactions as shown in the bellow figure, the fractional yield of 'R' in mixed reactor (for a given conversion of 'A'). (A) Decreases (B) Increases (C) Increases linearly (D) Remain same

Last Answer : (A) Decreases

One mole of nitrogen at 8 bar and 600 K is contained in a piston cylinder arrangement. It is brought to 1 bar isothermally against a resisting pressure of 1 bar. The work done (in Joules) by the gas is (A) 30554 (B) 10373 (C) 4988.4 (D) 4364.9

Description : One mole of nitrogen at 8 bar and 600 K is contained in a piston cylinder arrangement. It is brought to 1 bar isothermally against a resisting pressure of 1 bar. The work done (in Joules) by the gas is (A) 30554 (B) 10373 (C) 4988.4 (D) 4364.9

Last Answer : (B) 10373

With the same reaction time, initial concentration and feed rate, the reaction 2A → B is carried out separately in CSTR and P.F. reactor of equal volumes. The conversion will be (A) Higher in P.F. reactor (B) Higher in CSTR (C) Same in both the reactors (D) Data insufficient; can't be predicted

Description : With the same reaction time, initial concentration and feed rate, the reaction 2A → B is carried out separately in CSTR and P.F. reactor of equal volumes. The conversion will be (A) Higher in P.F. reactor (B) Higher in CSTR (C) Same in both the reactors (D) Data insufficient; can't be predicted

Last Answer : (A) Higher in P.F. reactor

For reactions in parallel viz A → P (desired product) and A → Q (unwanted product), if the order of the desired reaction is higher than that of the undesired reaction, a (A) Batch reactor is preferred over a single CSTR for high yield (B) Tubular reactor is preferred over a single CSTR for high yield (C) Both (A) and (B) (D) Single CSTR is the most suitable

Description : For reactions in parallel viz A → P (desired product) and A → Q (unwanted product), if the order of the desired reaction is higher than that of the undesired reaction, a (A) Batch reactor is preferred over a ... a single CSTR for high yield (C) Both (A) and (B) (D) Single CSTR is the most suitable

Last Answer : (C) Both (A) and (B)

An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The residence time required (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Description : An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The ... (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Last Answer : (C) 1.60

For the liquid phase zero order irreversible reaction A → B, the conversion of A in a CSTR is found to be 0.3 at a space velocity of 0.1min -1 . What will be the conversion for a PFR with a space velocity of 0.2 min -1? Assume that all the other operating conditions are the same for CSTR and PFR. (A) 0.15(B) 0.30 (C) 0.60 (D) 0.90

Description : For the liquid phase zero order irreversible reaction A → B, the conversion of A in a CSTR is found to be 0.3 at a space velocity of 0.1min -1 . What will be the conversion for a PFR with a space velocity of 0.2 min ... conditions are the same for CSTR and PFR. (A) 0.15 (B) 0.30 (C) 0.60 (D) 0.90

Last Answer : (C) 0.60

The conversion for a first order liquid phase reaction. A → B in a CSTRis 50%. If another CSTR of the same volume is connected in series, then the % conversion at the exit of the second reactor will be (A) 60 (B) 75 (C) 90 (D) 100

Description : The conversion for a first order liquid phase reaction. A → B in a CSTRis 50%. If another CSTR of the same volume is connected in series, then the % conversion at the exit of the second reactor will be (A) 60 (B) 75 (C) 90 (D) 100

Last Answer : (B) 75

Decomposition rate of a liquid 'X' which decomposes as per the reaction as shown in the bellow figure is given by: (A) K1 . CX (B) (K1 + K2 + K3 ) CX (C) (K1 + K2 ) CX (D) (K2 + K3 ) CX

Description : Decomposition rate of a liquid 'X' which decomposes as per the reaction as shown in the bellow figure is given by: (A) K1 . CX (B) (K1 + K2 + K3 ) CX (C) (K1 + K2 ) CX (D) (K2 + K3 ) CX

Last Answer : (C) (K1 + K2 ) CX

The thickness of oxide film is y at time t. If K1, K2 and K3 are the temperature dependent constants, the parabolic law of oxidation is given by (A) y2 = 2k1t + k2 (B) y = k1 ln (k2t + k3) (C) y = k1 t + k2 (D) y = k1t3 + k2

Description : The thickness of oxide film is y at time t. If K1, K2 and K3 are the temperature dependent constants, the parabolic law of oxidation is given by (A) y2 = 2k1t + k2 (B) y = k1 ln (k2t + k3) (C) y = k1 t + k2 (D) y = k1t3 + k2

Last Answer : Option A

Exothermic reactions are best carried out in (A) A CSTR (B) CSTR in series (C) A plug flow reactor followed by CSTR (D) CSTR followed by a plug flow reactor

Description : Exothermic reactions are best carried out in (A) A CSTR (B) CSTR in series (C) A plug flow reactor followed by CSTR (D) CSTR followed by a plug flow reactor

Last Answer : (D) CSTR followed by a plug flow reactor

Autocatalytic reactions are best carried out in a (A) CSTR (B) CSTR in series (C) Plug flow reactor (D) Recycle reactor

Description : Autocatalytic reactions are best carried out in a (A) CSTR (B) CSTR in series (C) Plug flow reactor (D) Recycle reactor

Last Answer : (D) Recycle reactor

Two springs of stiffness k1 and k2 are connected in series, the combined (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2

Description : Two springs of stiffness k1 and k2 are connected in series, the combined (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2

Last Answer : (A) k1k2/k1 + k2

Two springs of stiffness k1 and k2 are connected in parallel, the combined stiffness of the connection is given by, (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2

Description : Two springs of stiffness k1 and k2 are connected in parallel, the combined stiffness of the connection is given by, (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2

Last Answer : (C) k1 + k2

The equivalent stiffness of spring connected in parallel having stiffnesses k1 and k2 can be written as * 1 point (A)(1/k1) + (1/k2) (B) (1/k1) - (1/k2) (C) k1 + k2 (D) None of the above

Description : The equivalent stiffness of spring connected in parallel having stiffnesses k1 and k2 can be written as * 1 point (A)(1/k1) + (1/k2) (B) (1/k1) - (1/k2) (C) k1 + k2 (D) None of the above

Last Answer : (C) k1 + k2

Equivalent stiffness of spring connected in paralled having stiffness k1 and k2 can be given as A) K = k1+ k2 B) K = k1- k2 C) 1/k = 1/k1 + 1/k2 D) 1/k = 1/k1 - 1/k2

Description : Equivalent stiffness of spring connected in paralled having stiffness k1 and k2 can be given as A) K = k1+ k2 B) K = k1- k2 C) 1/k = 1/k1 + 1/k2 D) 1/k = 1/k1 - 1/k2

Last Answer : A) K = k1+ k2

Which of the following relations is true when springs are connected parallelly? where K = spring stiffness a.Ke= K1 +K2 b. (1/Ke)=(1/K1)+(1/K2) c.Ke= (1/K1)+(1/K2) d.None of the above

Description : Which of the following relations is true when springs are connected parallelly? where K = spring stiffness a.Ke= K1 +K2 b. (1/Ke)=(1/K1)+(1/K2) c.Ke= (1/K1)+(1/K2) d.None of the above

Last Answer : a.Ke= K1 +K2

Which of the following is the rate law for SN1 mechanisms? (a) Rate = k[Alkyl Halide] [Nucleophile] (b) Rate = k[Nucleophile] (c) Rate = k[Alkyl Halide](d) Rate = k1[Alkyl Halide] + k2[Nucleophile]

Description : Which of the following is the rate law for SN1 mechanisms? (a) Rate = k[Alkyl Halide] [Nucleophile] (b) Rate = k[Nucleophile] (c) Rate = k[Alkyl Halide] (d) Rate = k1[Alkyl Halide] + k2[Nucleophile]

Last Answer : Rate = k[Alkyl Halide]

Pure A in gas phase enters a reactor 50% of this A is converted to Bthrough the reaction, A → 3B. Mole fraction of A in the exit stream is(A) 1/2(B) 1/3(C) 1/4(D) 1/5

Description : Pure A in gas phase enters a reactor 50% of this A is converted to Bthrough the reaction, A → 3B. Mole fraction of A in the exit stream is (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Last Answer : (B) 1/3

Without finding the cubes, factorise: (2r-3s)3 +(3s -5t)3+ (5t-2r)3. -Maths 9th

Description : Without finding the cubes, factorise: (2r-3s)3 +(3s -5t)3+ (5t-2r)3. -Maths 9th

Last Answer : Solution :-

If `(2p+5q)/(2r+5s) = (4p-3q)/(4r-3s)`, then find the relation between p, q, r and s.

Description : If `(2p+5q)/(2r+5s) = (4p-3q)/(4r-3s)`, then find the relation between p, q, r and s.

Last Answer : If `(2p+5q)/(2r+5s) = (4p-3q)/(4r-3s)`, then find the relation between p, q, r and s.

Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Description : Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Last Answer : Answer: A

The gas phase reaction 2A ⇌ B is carried out in an isothermal plug flow reactor. The feed consists of 80 mole % A and 20 mole % inerts. If the conversion of A at the reactor exit is 50%, then CA/CA0 at the outlet of the reactor is (A) 2/3 (B) 5/8 (C) 1/3 (D) 3/8

Description : The gas phase reaction 2A ⇌ B is carried out in an isothermal plug flow reactor. The feed consists of 80 mole % A and 20 mole % inerts. If the conversion of A at the reactor exit is 50%, then CA/CA0 at the outlet of the reactor is (A) 2/3 (B) 5/8 (C) 1/3 (D) 3/8

Last Answer : (B) 5/8

A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume of the reacting mixture is V and the density of the liquid mixture is constant. The mass balance for A is (A) d(VCA )/dt = -F (CAF - CA ) - kCA 2V (B) d(VCA )/dt = F (CAF - CA ) - kCA 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Description : A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume ... 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Last Answer : (D) d(VCA )/dt = FCAF - kCA 2V

When an unknown capacitance is tested with a bridge, what is the value of Cx if R1 equals 70 ohms, R2 equals 150 ohms, and Cs equals 550 microfarads?

Description : When an unknown capacitance is tested with a bridge, what is the value of Cx if R1 equals 70 ohms, R2 equals 150 ohms, and Cs equals 550 microfarads?

Last Answer : 256 microfarads.

When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Description : When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Last Answer : 420 ohms.

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

A gas (density = 1.5 kg/m3 , viscosity = 2 × 10 ‒5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The pressure drop for another gas, with density of 1.5 kg/m3and viscosity of 3 × 10 ‒5kg/m.s flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m

Description : A gas (density = 1.5 kg/m3 , viscosity = 2 10 -5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The ... flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m

Last Answer : (B) 12600 Pa/m

An irreversible first order reaction is being carried out in a CSTR and PFR of same volume. The liquid flow rates are same. The relative conversion will (A) Be more in CSTR than in PFR (B) Be more in PFR than in CSTR (C) Be same in both cases (D) Depend on the temperature

Description : An irreversible first order reaction is being carried out in a CSTR and PFR of same volume. The liquid flow rates are same. The relative conversion will (A) Be more in CSTR than in PFR (B) Be more in PFR than in CSTR (C) Be same in both cases (D) Depend on the temperature

Last Answer : (B) Be more in PFR than in CSTR

Critical Speed (Nc ) of a ball mill is given by (where R1 and R2 are radii of ball mill and the ball respectively). (A) Nc = (1/4π). √(g/R1 - R2 ) (B) Nc = (1/2π). √(g/R1 - R2 ) (C) Nc = (1/π). √(g/R1 - R2 ) (D) Nc = (1/2π). √(R1 - R2 /g)

Description : Critical Speed (Nc ) of a ball mill is given by (where R1 and R2 are radii of ball mill and the ball respectively). (A) Nc = (1/4π). √(g/R1 - R2 ) (B) Nc = (1/2π). √(g/R1 - R2 ) (C) Nc = (1/π). √(g/R1 - R2 ) (D) Nc = (1/2π). √(R1 - R2 /g)

Last Answer : (B) Nc = (1/2π). √(g/R1 - R2 )

A sphere of radius 'R1 ' is enclosed in a sphere of radius 'R2 '. The view (or shape) factor for radiative heat transfer of the outer sphere with respect to the inner sphere is (A) 0 (B) R2 /(R1+R2 ) (C) 1 (D) (R1 /R2 )

Description : A sphere of radius 'R1 ' is enclosed in a sphere of radius 'R2 '. The view (or shape) factor for radiative heat transfer of the outer sphere with respect to the inner sphere is (A) 0 (B) R2 /(R1+R2 ) (C) 1 (D) (R1 /R2 )

Last Answer : (B) R2 /(R1+R2 )

Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to (A) (r2- r1)/r1. r2 (B) r1. r2/(r2- r1) (C) (r2 + r1)/r1. r2 (D) r1. r2/(r2 + r1)

Description : Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to (A) (r2- r1)/r1. r2 (B) r1. r2/(r2- r1) (C) (r2 + r1)/r1. r2 (D) r1. r2/(r2 + r1)

Last Answer : (B) r1. r2/(r2- r1)

A gas performs the maximum work, when it expands (A) Non-uniformly (B) Adiabatically (C) Isobarically (D) Isothermally

Description : A gas performs the maximum work, when it expands (A) Non-uniformly (B) Adiabatically (C) Isobarically (D) Isothermally

Last Answer : (C) Isobarically

The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = - 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Last Answer : (C) 600

The most unsuitable reactor for carrying out reactions in which high reactant concentration favours high yields is (A) Backmix reactor (B) Plug flow reactor (C) Series of CSTR (D) PFR in series

Description : The most unsuitable reactor for carrying out reactions in which high reactant concentration favours high yields is (A) Backmix reactor (B) Plug flow reactor (C) Series of CSTR (D) PFR in series

Last Answer : A) Backmix reactor

Let R1 and R2 be the remainders when the polynomials x^3 + 2x^2 – 5ax – 7 and x^2 + ax^2 – 12x + 6 are divided by (x + 1) and (x – 2) respectively. -Maths 9th

Description : Let R1 and R2 be the remainders when the polynomials x^3 + 2x^2 – 5ax – 7 and x^2 + ax^2 – 12x + 6 are divided by (x + 1) and (x – 2) respectively. -Maths 9th

Last Answer : answer:

What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Description : What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Last Answer : You need to mention whether the resistors are in series or parallel to get the right answer

What is the total current is V is 10 Volts R1 is 500 Ohms and R2 is 1500 ohms?

Description : What is the total current is V is 10 Volts R1 is 500 Ohms and R2 is 1500 ohms?

Last Answer : We need to find R equivalent at first then divide V from it to find the total current.Case 1: If resistances are connected in series.Then, R(eq.) = R1 + R2 = 500 + 1500 = 2000 ohmSo, Total current, I = V/R(eq.) = ... (500 + 1500) = 400 ohmSo, Total current, I = V/R(eq.) = 10/400 = 1/40 or 0.025 A.

What is the total resistance is V is 10 volts R1 is 1000 ohms and R2 is 1000 Ohms?

Description : What is the total resistance is V is 10 volts R1 is 1000 ohms and R2 is 1000 Ohms?

Last Answer : If they're connected in series the total resistance is 2000 ohms. If they're connected in parallel the resistance is 500 ohms.

Two planets have the same density of matter, such that their masses are proportional to the cube of their radii. The ratio of their acceleration due to gravity on their surfaces is (a) r2/r1 (b) (r1/r2)2 (c) r1/r2 (d) (r2/r1)2

Description : Two planets have the same density of matter, such that their masses are proportional to the cube of their radii. The ratio of their acceleration due to gravity on their surfaces is (a) r2/r1 (b) (r1/r2)2 (c) r1/r2 (d) (r2/r1)2

Last Answer : Ans:(d) Direction: In the following question, a statement of Assertion (A) is given followed by corresponding Reason (R), just below it. Read the statements carefully and mark the correct answer: (a) If both A and ... true but R is not the correct explanation of A. (c) If A is true but R is false

weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Description : weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Last Answer : ANS: A

What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: D

In the illustrated circut, if the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms. What is the total resistance? EL-0032 A. 15 ohms B. 20 ohms C. 25 ohms D. 30 ohms

Description : In the illustrated circut, if the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms. What is the total resistance? EL-0032 A. 15 ohms B. 20 ohms C. 25 ohms D. 30 ohms

Last Answer : Answer: A

The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across 'R1', 'R2' and 'R3' will be different if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Last Answer : Answer: B

Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Description : Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Last Answer : Answer: A

As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow through 'R1' will equal the current flow through 'R2' C. the energy dissipated in 'R1' will be the same as the energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Last Answer : Answer: D

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: B