Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Typical solvent polymerisation reaction conditions for the production
of high density polythene by Zeigler process is
(A) 7 kgf/cm2 and 70 °C
(B) 1000 kgf/cm2 and 100°C
(C) 7 kgf/cm2 and 700°C
(D) 1 kgf/cm2
(gage) and 70°C
by

1 Answer

Answer :

(A) 7 kgf/cm2 and 70 °C
by

Related questions

Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Description : Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Last Answer : (B) Achieves an yield of 95-98% based on ethylene

Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm

Description : Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm

Last Answer : (A) 5°C and 1 kgf/cm

Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Description : Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Last Answer : (A) 50°C and 3 - 4 kg/cm

Zeigler process (A) Produces high density polythene(B) Uses no catalyst(C) Produces low density polythene(D) Employs very high pressure

Description : Zeigler process (A) Produces high density polythene (B) Uses no catalyst (C) Produces low density polythene (D) Employs very high pressure

Last Answer : (A) Produces high density polythene

Operating condition in the electrical dehydrators for crude oil is about (A) 6.5 kgf/Cm2 & 95°C (B) 1 atm. & 110 °C (C) 20 kgf/cm2 & 110°C (D) 50 atm. and 150°C

Description : Operating condition in the electrical dehydrators for crude oil is about (A) 6.5 kgf/Cm2 & 95°C (B) 1 atm. & 110 °C (C) 20 kgf/cm2 & 110°C (D) 50 atm. and 150°C

Last Answer : (A) 6.5 kgf/Cm2 & 95°C

Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Description : Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Last Answer : (D) Aluminium triethyl combined with titanium tetrachloride

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of light distillates (B) Suppress coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Last Answer : (B) Suppress coke formation

Zeigler - Natta catalyst (AlR3 - AlCl3 ) is used in the polymerisation of (A) Vinyl acetate (B) Vinyl chloride (C) Propylene (D) Styrene

Description : Zeigler - Natta catalyst (AlR3 - AlCl3 ) is used in the polymerisation of (A) Vinyl acetate (B) Vinyl chloride (C) Propylene (D) Styrene

Last Answer : (C) Propylene

Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Description : Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Last Answer : (B) 135

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 88-90°c

ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 71-82°c

Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Description : Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Last Answer : (D) Polyhexamethylene adipamide

Pressure of CO2 gas (which is a coolant) in the Calder-Hall nuclear reactor is __________ kgf/cm2 . (A) 0.2 (B) 7 (C) 35 (D) 50

Description : Pressure of CO2 gas (which is a coolant) in the Calder-Hall nuclear reactor is __________ kgf/cm2 . (A) 0.2 (B) 7 (C) 35 (D) 50

Last Answer : (B) 7

In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Description : In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C. (A) 20 (B) 60 (C) 120 (D) ∞

Last Answer : (D) ∞

Zeigler process (A) Produces high density polyethylene (B) Produces low density polyethylene (C) Uses no catalyst (D) Employs very high pressure

Description : Zeigler process (A) Produces high density polyethylene (B) Produces low density polyethylene (C) Uses no catalyst (D) Employs very high pressure

Last Answer : (A) Produces high density polyethylene

Catalyst used in the production of high density polythene by low pressure Ziegler process is(A) Aluminium triethyl activated with TiCl4(B) Platinum(C) Molybdenum(D) Nickel

Description : Catalyst used in the production of high density polythene by low pressure Ziegler process is (A) Aluminium triethyl activated with TiCl4 (B) Platinum (C) Molybdenum (D) Nickel

Last Answer : (A) Aluminium triethyl activated with TiCl4

Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Description : Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Last Answer : (B) 15-45 Kgf/cm2 & 450-550°C

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

__________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Description : __________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Last Answer : (C) Plunger

Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C

Description : Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C

Last Answer : (A) 4 kgf/cm2 & 500°C

Normal temperature and pressure (N.T.P.) corresponds to (A) 0°C and 760 mm Hg (B) 15°C and 760 mm Hg (C) 20°C and 760 mm Hg (D) 0°C and 1 kgf/cm2

Description : Normal temperature and pressure (N.T.P.) corresponds to (A) 0°C and 760 mm Hg (B) 15°C and 760 mm Hg (C) 20°C and 760 mm Hg (D) 0°C and 1 kgf/cm2

Last Answer : (C) 20°C and 760 mm Hg

A typical example of an exothermic reversible reaction conducted at high pressure in industry is (A) Dehydration of ethanol (B) Methanol synthesis (C) Reformation of methane (D) Polymerisation of ethylene

Description : A typical example of an exothermic reversible reaction conducted at high pressure in industry is (A) Dehydration of ethanol (B) Methanol synthesis (C) Reformation of methane (D) Polymerisation of ethylene

Last Answer : (A) Dehydration of ethanol

The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2(D) 400 kg/cm2

Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the  point is:  (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2

Last Answer : (A) 100 kg/cm2

One barometric pressure or 1 atmospheric pressure is equal to  (a) 1 kgf/cnr2  (b) 1.033 kgf/cm2  (c) 0 kgf/cm2  (d) 1.0197 kgf/cm2  (e) 100 kgf/cm2.

Description : One barometric pressure or 1 atmospheric pressure is equal to  (a) 1 kgf/cnr2  (b) 1.033 kgf/cm2  (c) 0 kgf/cm2  (d) 1.0197 kgf/cm2  (e) 100 kgf/cm2.

Last Answer : Answer : b

I kgf/cm2 is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) l00 mm Hg.

Description : I kgf/cm2 is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) l00 mm Hg.

Last Answer : Answer : c

Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Description : Pick out the wrong statement. (A) Polymeric fibres are never produced by addition polymerisation (B) Property of tackiness is exhibited by uncured rubber (C) Sharp melting point is not observed in thermoplastic polymers (D) Polythene generally has an excellent resistance to ultra violet rays

Last Answer : (A) Polymeric fibres are never produced by addition polymerisation

Condensation polymerisation is not involved in the manufacture of (A) Teflon (B) Polythene (C) Terylene (D) Nylon

Description : Condensation polymerisation is not involved in the manufacture of (A) Teflon (B) Polythene (C) Terylene (D) Nylon

Last Answer : (B) Polythene

Polythene is a/an (A) Addition polymerisation product (B) Condensation polymerisation product (C) Thermosetting material (D) None of these

Description : Polythene is a/an (A) Addition polymerisation product (B) Condensation polymerisation product (C) Thermosetting material (D) None of these

Last Answer : (A) Addition polymerisation product

Which of the following is produced by condensation polymerisation? (A) Bakelite (B) Polythene (C) Poly vinyl chloride (D) Polystyrene

Description : Which of the following is produced by condensation polymerisation? (A) Bakelite (B) Polythene (C) Poly vinyl chloride (D) Polystyrene

Last Answer : (A) Bakelite

Polythene is a/an __________ polymerisation product. (A) Addition (B) Condensation (C) Thermosetting (D) None of these

Description : Polythene is a/an __________ polymerisation product. (A) Addition (B) Condensation (C) Thermosetting (D) None of these

Last Answer : (A) Addition

Feed water usually at…… °C temperature. a) 70 b) 120 c) 1000 d) 80

Description : Feed water usually at…… °C temperature. a) 70 b) 120 c) 1000 d) 80

Last Answer : d) 80

lass Ionomer Cement sets because of,** A. Acid-Base reaction B. Addition polymerisation reaction C. Growth of glass crystals D. Slip plane locking E. Solvent evaporation

Description : lass Ionomer Cement sets because of,** A. Acid-Base reaction B. Addition polymerisation reaction C. Growth of glass crystals D. Slip plane locking E. Solvent evaporation

Last Answer : A. Acid-Base reaction

Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Last Answer : (D) 250-280

90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C. (A) -5 (B) 10-30 (C) 250-280 (D) 500-600

Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C. (A) -5 (B) 10-30 (C) 250-280 (D) 500-600

Last Answer : (C) 250-280

90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at __________ °C. (A) < 0 (B) 10-30(C) 250-280 (D) 500-600

Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at __________ °C. (A) < 0 (B) 10-30 (C) 250-280 (D) 500-600

Last Answer : (B) 10-30

Pick out the wrong statement (A) A horizontal line on the humidity chart indicates the temperature changes at constant molal humidity (B) When water is cooled from 80 to 70°C by exposure to the air with a wet bulb temperature of 60°C, then both the approach & the range would be 10°C (C) For unsaturated air-water vapor mixture at atmospheric conditions, the wet bulb temperature & adiabatic cooling lines are the same (D) Relative saturation of unsaturated mixture of water vapor & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

Description : Pick out the wrong statement (A) A horizontal line on the humidity chart indicates the temperature changes at constant molal humidity (B) When water is cooled from 80 to 70°C by exposure ... & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

Last Answer : (D) Relative saturation of unsaturated mixture of water vapor & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

The polymerisation of which of the Following is used in manufacturing of polythene in industry? (1) Methane (2) Styrene (3) Acetylene (4) Ethylene

Description : The polymerisation of which of the Following is used in manufacturing of polythene in industry? (1) Methane (2) Styrene (3) Acetylene (4) Ethylene

Last Answer : (4) Ethylene Explanation: Ethylene is a rather stable molecule that polymerizes only upon contact with catalysts. The conversion is highly exothermic, that is the process releases a lot of heat. ... is the most pervasive technology, which means that metal chlorides or metal oxides are used.

The polymerisation of which of the following is used in manufacturing of polythene in industry ? (1) Methane (2) Styrene (3) Acetylene (4) Ethylene

Description : The polymerisation of which of the following is used in manufacturing of polythene in industry ? (1) Methane (2) Styrene (3) Acetylene (4) Ethylene

Last Answer : Ethylene

In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Description : In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament ... is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Last Answer : (B) PVC

The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Last Answer : (B) 1 and 200

Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Last Answer : (A) 700 - 1000

__________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C. (A) Veneering (B) Galvanising (C) Electroplating (D) Calorising

Description : __________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C. (A) Veneering (B) Galvanising (C) Electroplating (D) Calorising

Last Answer : (D) Calorising

For every 10°C rise in temperature, the rate of chemical reaction doubles. When the temperature is increased from 30 to 70°C, the rate of reaction increases __________ times. (A) 8 (B) 12 (C) 16 (D) 32

Description : For every 10°C rise in temperature, the rate of chemical reaction doubles. When the temperature is increased from 30 to 70°C, the rate of reaction increases __________ times. (A) 8 (B) 12 (C) 16 (D) 32

Last Answer : (C) 16

What is the specific weight of water at standard condition? (Formula: γ = ρg / k)  a. 1000 kgm/m3  b. 9.8066 m/s2  c. 1000 kgf/m3  d. None of the above

Description : What is the specific weight of water at standard condition? (Formula: γ = ρg / k)  a. 1000 kgm/m3  b. 9.8066 m/s2  c. 1000 kgf/m3  d. None of the above

Last Answer : 1000 kgf/m3

Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Description : Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Last Answer : (B) 70

Hardening is a process of heating a metal to a) 400°C b) 500°C c) 600°C d) 700°C

Description : Hardening is a process of heating a metal to a) 400°C b) 500°C c) 600°C d) 700°C

Last Answer : c) 600°C

Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are normally carried out at about __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Last Answer : (B) 900-1000

__________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Description : __________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Last Answer : (A) High density