Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)

Actual lift of a pump is always less than the theoretical lift and is limited
by the
(A) Specific gravity & temperature of the liquid
(B) Leakage & pressure decreasing at higher elevations
(C) Frictional resistance through pipes, fittings & passages
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Horsepower requirement for given pump capacity depends upon the (A) Specific gravity of the liquid (B) Suction lift (C) Discharge head (D) All (A), (B) and (C)

Description : Horsepower requirement for given pump capacity depends upon the (A) Specific gravity of the liquid (B) Suction lift (C) Discharge head (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration permanently. 4. Have nearly uniform discharge. Which of these statements are corrects? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Last Answer : (d) 1, 2, 3 & 4

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Last Answer : (C) 8

What is the maximum theoretical suction lift (metres) of a reciprocating pump? (A) 5 (B) 10(C) 50 (D) 100

Description : What is the maximum theoretical suction lift (metres) of a reciprocating pump? (A) 5 (B) 10(C) 50 (D) 100

Last Answer : (B) 10

What is dense cold air that flows from higher to lower elevations due to gravity?

Description : What is dense cold air that flows from higher to lower elevations due to gravity?

Last Answer : Need answer

When the water is warm, the height to which it can be lifted by a pump (A) Decreases due to reduced viscosity (B) Decreases due to reduced vapour pressure (C) Increases due to increased vapour pressure (D) Decreases due to increased frictional resistance

Description : When the water is warm, the height to which it can be lifted by a pump (A) Decreases due to reduced viscosity (B) Decreases due to reduced vapour pressure (C) Increases due to increased vapour pressure (D) Decreases due to increased frictional resistance

Last Answer : (B) Decreases due to reduced vapour pressure

When flanged fittings are to be used at temperatures below -20°F, what pressure rating is to be used? a) The pressure rating at the actual service temperature, found by interpretation. b) The pressure rating at -20°F. c) The pressure equal to the flange class. d) Flanges complying with ASME B16.5 may not be used below -20°F.

Description : When flanged fittings are to be used at temperatures below -20°F, what pressure rating is to be used? a) The pressure rating at the actual service temperature, found by interpretation. b) The pressure ... to the flange class. d) Flanges complying with ASME B16.5 may not be used below -20°F.

Last Answer : b) The pressure rating at -20°F.

A pump operating under specific conditions delivers insufficient quantity of liquid. This may be set right by (A) Decreasing the size of the inlet pipe (B) Increasing the size of the inlet pipe (C) Lowering the pump position (D) Both (B) and (C)

Description : A pump operating under specific conditions delivers insufficient quantity of liquid. This may be set right by (A) Decreasing the size of the inlet pipe (B) Increasing the size of the inlet pipe (C) Lowering the pump position (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid(C) The flow of fluid through the pipe is suddenly brought to rest by closing of the valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Description : The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid (C) The flow of fluid through the pipe is suddenly brought to ... valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Last Answer : Answer: Option C

Coefficient of resistance is the ratio of (A) Actual velocity of jet at vena-contracta to the theoretical velocity (B) Area of jet at vena-contracta to the area of orifice (C) Loss of head in the orifice to the head of water available at the exit of the orifice (D) Actual discharge through an orifice to the theoretical discharge

Description : Coefficient of resistance is the ratio of (A) Actual velocity of jet at vena-contracta to the theoretical velocity (B) Area of jet at vena-contracta to the area of orifice (C) Loss ... available at the exit of the orifice (D) Actual discharge through an orifice to the theoretical discharge

Last Answer : Answer: Option C

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Last Answer : (c) Superior load carrying capacity at higher speeds

The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Last Answer : e) all of the above*

Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Description : Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Last Answer : (D) All the above

Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Description : Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Last Answer : (D) All the above

Two pipe P & Q fill a tab in 5 hrs and 20 hrs respectively. If both the pipes are open then due to the leakage, it took 30mins more to fill the tab. If the tab is full, how long will it take for the leakage alone to empty the tank? A) 28 B) 24 C) 36 D) 12

Description : Two pipe P & Q fill a tab in 5 hrs and 20 hrs respectively. If both the pipes are open then due to the leakage, it took 30mins more to fill the tab. If the tab is full, how long will it take for the leakage alone to empty the tank? A) 28 B) 24 C) 36 D) 12

Last Answer : C Part filled by(P+Q) in 1 hr = 1/5 + 1/20 = ¼ So P & Q together can fill the tank in 4 hrs. Work done by the leak in 1 hr = 1 / 4 - 2/9 Leak will empty the tank in 36 hrs.

In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ * 1 point (A) Frictional resistance (B) Work done(C) Fluid pressure (D) Air pressure

Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ * 1 point (A) Frictional resistance (B) Work done(C) Fluid pressure (D) Air pressure

Last Answer : (A) Frictional resistance

In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ a) Frictional resistance b) Work done c) Fluid pressure d) Air pressure

Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ a) Frictional resistance b) Work done c) Fluid pressure d) Air pressure

Last Answer : a) Frictional resistance

In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

Is there an online dictionary that quotes actual passages from literature to show how words are used in context?

Description : Is there an online dictionary that quotes actual passages from literature to show how words are used in context?

Last Answer : Perhaps a literary dictionary?

The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Description : The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Last Answer : (A) Area of surface in contact

Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Description : Delivery of insufficient quantity of liquid by a pump may be caused by (A) Air leak in the inlet (B) Low rpm (C) Too high a lift (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Cd , Cc and Cv are related (for flow through an orifice) as (where, Cd = discharge co-efficient, Cc = co-efficient of contraction = (area of jet at vena￾contracta/area of opening), Cv = co-efficient of velocity = (actual velocity at vena-contracta/theoretical velocity). (A) Cd = Cc /Cv (B) Cd = Cc .Cv (C) Cd = Cv / Cc (D) None of these

Description : Cd , Cc and Cv are related (for flow through an orifice) as (where, Cd = discharge co-efficient, Cc = co-efficient of contraction = (area of jet at vena￾contracta/area of opening), Cv = co-efficient of velocity = (actual velocity ... A) Cd = Cc /Cv (B) Cd = Cc .Cv (C) Cd = Cv / Cc (D) None of these

Last Answer : (B) Cd = Cc .Cv

Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Description : Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Last Answer : (A) Increase

A ball bounces higher at high altitudes than in plains. This is because (a) the pressure on higher altitudes is lower than that in plains (b) Downward pull due to gravity is less at higher altitudes (c) The rarefied air offers less resistance to the ball (d) You become more energetic at hills, so greater the force applied, higher goes the ball.

Description : A ball bounces higher at high altitudes than in plains. This is because (a) the pressure on higher altitudes is lower than that in plains (b) Downward pull due to gravity is less at higher altitudes ... ball (d) You become more energetic at hills, so greater the force applied, higher goes the ball.

Last Answer : Ans:(a)

Suction lift of a pump depends upon (A) Atmospheric pressure (B) Water temperature (C) Velocity of water in suction pipe (D) All the above

Description : Suction lift of a pump depends upon  (A) Atmospheric pressure  (B) Water temperature  (C) Velocity of water in suction pipe  (D) All the above 

Last Answer : (D) All the above 

Compressibility factor (i.e., the ratio of actual volume of gas to the volume predicted by ideal gas law) for all gases are (A) Always greater than one (B) Same at the same reduced temperature (C) Same at the same reduced pressure (D) Both (B) & (C)

Description : Compressibility factor (i.e., the ratio of actual volume of gas to the volume predicted by ideal gas law) for all gases are (A) Always greater than one (B) Same at the same reduced temperature (C) Same at the same reduced pressure (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

A hydrometer is used to measure the ____________. A. specific gravity of a battery electrolyte B. water pressure in a deck pipeline C. amount of potable water a vessel is taking on D. power developed by a salt water service pump

Description : A hydrometer is used to measure the ____________. A. specific gravity of a battery electrolyte B. water pressure in a deck pipeline C. amount of potable water a vessel is taking on D. power developed by a salt water service pump

Last Answer : Answer: A

Select the correct statement. (A) A contour is not necessarily a closed curve. B) A contour represents a ridge line if the concave side of lower value contour lies towards the higher value contour (C) Two contours of different elevations do not cross each other except in case of an overhanging cliff (D) All of the above statements are correct

Description : Select the correct statement. (A) A contour is not necessarily a closed curve. B) A contour represents a ridge line if the concave side of lower value contour lies towards the higher value contour ... each other except in case of an overhanging cliff (D) All of the above statements are correct

Last Answer : (C) Two contours of different elevations do not cross each other except in case of an overhanging clif

20. The coefficient of discharge is the ratio of theoretical discharge to the actual discharge through an orifice. A) True B) False

Description : 20. The coefficient of discharge is the ratio of theoretical discharge to the actual discharge through an orifice. A) True B) False

Last Answer : B

Coefficient of velocity is defined as the ratio of (A) Actual velocity of jet at vena contracta to the theoretical velocity (B) Area of jet at vena contracta to the area of orifice (C) Actual discharge through an orifice to the theoretical discharge (D) None of the above

Description : Coefficient of velocity is defined as the ratio of (A) Actual velocity of jet at vena contracta to the theoretical velocity (B) Area of jet at vena contracta to the area of orifice (C) Actual discharge through an orifice to the theoretical discharge (D) None of the above

Last Answer : Answer: Option A

The weight per unit volume of a liquid at a standard temperature and pressure is called (A) Specific weight (B) Mass density (C) Specific gravity (D) None of these

Description : The weight per unit volume of a liquid at a standard temperature and pressure is called (A) Specific weight (B) Mass density (C) Specific gravity (D) None of these

Last Answer : Answer: Option A

The mass per unit volume of a liquid at a standard temperature and pressure is called (A) Specific weight (B) Mass density (C) Specific gravity (D) None of these

Description : The mass per unit volume of a liquid at a standard temperature and pressure is called (A) Specific weight (B) Mass density (C) Specific gravity (D) None of these

Last Answer : Answer: Option B

What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited NPSHa (net positive suction head available)?

Description : What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited NPSHa (net positive suction head available)?

Last Answer : This application is nearly perfect for a turbine regenerative type of pump. Factors that immediately identify your application and pump type are the small flowrate, low NPSHa, and high temperature. The ... in pressure. You can visit the site below to learn more about these types of pumps.

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Purpose of air lift pump is to (A) Compress air (B) Lift compressed air (C) Lift water from a well by using compressed air (D) Lift air under negative pressure

Description : Purpose of air lift pump is to (A) Compress air (B) Lift compressed air (C) Lift water from a well by using compressed air (D) Lift air under negative pressure

Last Answer : (C) Lift water from a well by using compressed air

Good design of the casing of a centrifugal pump aims at minimising the (A) Cavitation (B) Frictional losses (C) Kinetic energy loss (D) Static head

Description : Good design of the casing of a centrifugal pump aims at minimising the (A) Cavitation (B) Frictional losses (C) Kinetic energy loss (D) Static head

Last Answer : Option C

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

Runoff is the quantity of water which flows (A) In sewer pipes (B) Due to leakage in pipes (C) In rivers (D) None of these

Description : Runoff is the quantity of water which flows (A) In sewer pipes (B) Due to leakage in pipes (C) In rivers (D) None of these

Last Answer : (C) In rivers

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Description : Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Last Answer : (B) 0.62

Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Description : Co-efficient of discharge (Cd ) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv ; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about (A) 0.42 (B) 0.62 (C) 0.82 (D) 0.98

Last Answer : (B) 0.62

Straight run petrol as compared to methyl/ethyl alcohol has (A) Lower calorific value (B) Lower octane number (C) Higher specific gravity (D) Higher ignition temperature

Description : Straight run petrol as compared to methyl/ethyl alcohol has (A) Lower calorific value (B) Lower octane number (C) Higher specific gravity (D) Higher ignition temperature

Last Answer : (B) Lower octane number

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7