Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37
Last Answer : (C) 8
Description : Acceleration head in a reciprocating pump (A) Increases the work done during delivery stroke (B) Decreases the work done during suction stroke (C) Does not change the work requirement of the pump (D) Increases the work done during suction stroke
Last Answer : (C) Does not change the work requirement of the pump
Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe
Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump
Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4
Last Answer : (d) 1, 2, 3 & 4
Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)
Last Answer : (D) All (A), (B), and (C)
Description : If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict
Last Answer : (A) Increases
Description : Horsepower requirement for given pump capacity depends upon the (A) Specific gravity of the liquid (B) Suction lift (C) Discharge head (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)
Description : Suction lift of a pump depends upon (A) Atmospheric pressure (B) Water temperature (C) Velocity of water in suction pipe (D) All the above
Last Answer : (D) All the above
Description : Consider the following statements: The total head against which a pump has to work must include, besides any other items, 1. the suction lift. 2. the delivery head. 3. the head lost due to friction at entrance in the rising main. 4. the ... 2 & 3 only (b) 2 & 3 only (c) 1, 2, 3 & 4 (d) 3 & 4 only
Last Answer : (c) 1, 2, 3 & 4
Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*
Last Answer : e) all of the above*
Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these
Last Answer : (C) Deep well turbine pump
Description : In a two stage reciprocating air compressor, the suction and delivery pressure are 1 and 4 bar respectively. For maximum efficiency the intercooler pressure is A. 1.5 bar B. 2 bar C. 2.5 bar D. 3 bar
Last Answer : ANSWER : B
Description : In a two stage reciprocating air compressor with a suction pressure of 2 bar and delivery pressure of 8 bar the ideal intercooler pressure will be A. 10 bar B. 6 bar C. 4 bar D. 3 bar
Last Answer : ANSWER : C
Description : A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Last Answer : ANSWER : A
Description : In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke
Description : In a single stage reciprocating air compressor, the work done on air to compressor is from suction pressure to delivery pressure will be minimum when the compression is A. Isothermal process B. Adiabatic process C. Polytropic process D. Constant pressure process.
Description : A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Description : Pick out the wrong statement pertaining to the rotary dryer. (A) Flights (located in the inside shell of rotary dryer) lift the material being dried and shower it down through the current of ... D) Recommended peripheral speed of a rotary drier is in the range of 10 to 30 metres/minute
Last Answer : (C) Rotary dryer is suitable for drying sticky materia
Description : In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these
Last Answer : (C) Steam jet ejector with a barometric condenser
Description : Circulation pump is located below the evaporator to (A) Avoid cavitation (B) Avoid frequent priming (C) Create more suction head (D) None of these
Last Answer : (C) Create more suction head
Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these
Last Answer : (D) None of these
Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure
Last Answer : (A) Greater than the vapour pressure of the liquid
Description : What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure (C) Low suction pressure (D) High suction velocity
Last Answer : (C) Low suction pressure
Description : Cavitation can be prevented by (A) Suitably designing the pump (B) Maintaining the suction head sufficiently greater than the vapour pressure (C) Maintaining suction head = developed head (D) Maintaining suction head lower than the vapour pressure
Last Answer : (B) Maintaining the suction head sufficiently greater than the vapour pressure
Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature
Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature
Description : A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump. (A) Sump (B) Volute (C) Vacuum (D) Submerged
Last Answer : (C) Vacuum
Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head
Last Answer : (A) Less than the vapour pressure of the liquid at that temperature
Description : Capacity of a rotary gear pump can be varied by (A) Changing the speed of rotation (B) Bleeding air into suction (C) Bypassing liquid from the suction or discharge line (D) All (A), (B) and (C)
Description : Foot valves are provided in the suction line of a centrifugal pump to (A) Avoid priming, every time we start the pump (B) Remove the contaminant present in the liquid (C) Minimise the fluctuation in discharge (D) Control the liquid discharge
Last Answer : (A) Avoid priming, every time we start the pump
Description : What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited NPSHa (net positive suction head available)?
Last Answer : This application is nearly perfect for a turbine regenerative type of pump. Factors that immediately identify your application and pump type are the small flowrate, low NPSHa, and high temperature. The ... in pressure. You can visit the site below to learn more about these types of pumps.
Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute
Last Answer : (A) Electromagnetic
Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic
Last Answer : (B) Diaphragm
Description : Air vessel provided in a reciprocating pump is for (A) Increasing the acceleration head (B) Making the friction in pipe uniform (C) Decreasing the acceleration head (D) None of these
Last Answer : (B) Making the friction in pipe uniform
Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm
Last Answer : (C) Multistage centrifugal
Description : Air vessel provided in a reciprocating pump (A) Smoothens the flow by avoiding pulsations (B) Increases the volumetric efficiency of the pump (C) Saves the pump from the danger of cavitation (D) None of these
Description : A hydraulic ram acts as a/an __________ pump. (A) Centrifugal (B) Reciprocating (C) Impulse (D) Parallel cylinder
Last Answer : (C) Impulse
Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these
Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder
Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear
Last Answer : (A) Centrifugal
Description : Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal
Last Answer : (D) Centrifugal
Description : A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double (A) Head (B) Discharge (C) Efficiency (D) None of these
Last Answer : (B) Discharge
Description : Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations
Last Answer : (C) Higher capital &maintenance cost
Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal
Last Answer : (C) Diaphragm
Description : Pump used for the transportation of molten sodium in a fast breader reactor is a/an __________ pump. (A) Reciprocating (B) Plunger (C) Electromagnetic (D) Gear
Last Answer : (C) Electromagnetic
Description : Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm
Last Answer : (C) Centrifugal
Description : Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump
Last Answer : (D) Duplex/triplex reciprocating pump
Description : At what value of crank angle (roughly), no flow of water from or into the air vessel takes place in case of a double acting reciprocating pump? (A) 40° and 140° (B) 45° and 60° (C) 90° and 80° (D) 20° and 120°
Last Answer : (A) 40° and 140
Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum
Last Answer : (A) Reciprocating
Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump
Last Answer : (C) Gear pump