Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Pick up the correct statement from the following:
(A) All pipes and fittings are classified according to their diameters
(B) The diameter of the pipes is the nominal diameter of internal bore
(C) All pipes are measured along the centre line of the pipes in metres
(D) All the above
by

1 Answer

Answer :

(D) All the above
by

Related questions

Pick up the correct statement in case of water supply. (A) Pipes laid in trenches and pipes fixed to walls are measured separately (B) Cutting through walls and floors are included with the item (C) Pipes are classified according to their sizes and quality (D) All the above

Description : Pick up the correct statement in case of water supply. (A) Pipes laid in trenches and pipes fixed to walls are measured separately (B) Cutting through walls and floors are included with the item (C) Pipes are classified according to their sizes and quality (D) All the above

Last Answer : (D) All the above

Pick up the wrong nominal internal diameter of cast iron (spun) pipes in mm from the following: (A) 300 (B) 400 (C) 550 (D) 650

Description : Pick up the wrong nominal internal diameter of cast iron (spun) pipes in mm from the following: (A) 300 (B) 400 (C) 550 (D) 650

Last Answer : (C) 550

Pick up the correct statement from the following: (A) Detailed survey is carried out for a strip of land about 30 m at sharp curves (B) Levels are taken along the trace cut at an interval of 20 m (C) Contour interval is generally adopted at 2 metres vertical interval (D) All the above

Description : Pick up the correct statement from the following: (A) Detailed survey is carried out for a strip of land about 30 m at sharp curves (B) Levels are taken along the trace cut at an interval of 20 m (C) Contour interval is generally adopted at 2 metres vertical interval (D) All the above

Last Answer : Answer: Option D

Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Description : Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) The internal pressure within a pipe, is caused due to water head and hammer pressure (B) In pressure pipes with water at rest, the pressure is equal to water head (C) Sudden closure of a valve, causes the water hammer pressure (D) All the above

Description : Pick up the correct statement from the following:  (A) The internal pressure within a pipe, is caused due to water head and hammer pressure  (B) In pressure pipes with water at rest, the pressure ... (C) Sudden closure of a valve, causes the water hammer pressure  (D) All the above 

Last Answer : (D) All the above 

Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The spacing of inclined borings is kept such that one bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Description : Pick up the correct statement from the following: (A) Inclined borings are made for taking samples under existing structures (B) Inclined borings are occasionally used instead of vertical holes (C) The ... bore hole is vertically above the bottom of an adjacent bore hole (D) All the above

Last Answer : Answer: Option D

All pipes of a particular nominal size have the same (A) Inside diameter (B) Outside diameter (C) Thickness (D) None of these

Description : All pipes of a particular nominal size have the same (A) Inside diameter (B) Outside diameter (C) Thickness (D) None of these

Last Answer : (B) Outside diameter

Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Description : Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to the shape of the particles, concrete aggregates are classified as rounded irregular, angular and flaky (C) According to the surface texture of the particles, the concrete aggregates are classified as glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Description : Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to ... glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m diameter are designed as running 2/3rd or 3/4th full at maximum discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Description : Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m ... discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Last Answer : ANS: D

Pick up the correct statement from the following: A. The water supply pipes carry pure water free from solid particles B. The water supply pipes get clogged if flow velocity is less than self cleansing velocity C. The sewers may be carried up and down the hills and valleys D. The sewer pipes are generally laid along level hills

Description : Pick up the correct statement from the following: A. The water supply pipes carry pure water free from solid particles B. The water supply pipes get clogged if flow velocity is less than self ... carried up and down the hills and valleys D. The sewer pipes are generally laid along level hills

Last Answer : ANS: A

Consider two pipes of same length and diameter through which water is passed at the same velocity. The friction factor for rough pipe is f1 and that for smooth pipe is f2 . Pick out the correct statement(A) f1 = f2 (B) f1 < f2 (C) f1 > f2 (D) Data not sufficient to relate f1 & f2

Description : Consider two pipes of same length and diameter through which water is passed at the same velocity. The friction factor for rough pipe is f1 and that for smooth pipe is f2 . Pick out the correct statement. (A) f1 = f2 (B) f1 < f2 (C) f1 > f2 (D) Data not sufficient to relate f1 & f2

Last Answer : (C) f1 > f2

If Q is discharge is cubic metres per sec and D is the economical diameter of the pipe. According to Lea (A) D = 0.67 to 0.87 Q (B) D = 0.77 to 0.97 Q (C) D = 0.97 to 1.22 Q (D) D = 1.22 to 1.33 Q

Description : If Q is discharge is cubic metres per sec and D is the economical diameter of the pipe. According to Lea (A) D = 0.67 to 0.87 Q (B) D = 0.77 to 0.97 Q (C) D = 0.97 to 1.22 Q (D) D = 1.22 to 1.33 Q

Last Answer : (C) D = 0.97 to 1.22 Q

Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)

Description : Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick up the correct statement from the following: (A) Long tangent sections exceeding 3 km in length should be avoided (B) Curve length should be at least 150 metres for a deflection angle of 5 degree (C) For every degree decrease in the deflection angle, 30 metre length of curve to be increased (D) All the above

Description : Pick up the correct statement from the following: (A) Long tangent sections exceeding 3 km in length should be avoided (B) Curve length should be at least 150 metres for a deflection angle of 5 ... decrease in the deflection angle, 30 metre length of curve to be increased (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the curves of radii less than 750 m if the embankments are between 3 metres and 6 metres (C) Guard stones are provided at 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Description : Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the ... 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Minimum desirable width of medians on rural highways is 5 metres (B) Minimum width of medians should be 3 metres (C) On long bridges and viaducts, the width of medians should be 1.5 m (D) All the above

Description : Pick up the correct statement from the following: (A) Minimum desirable width of medians on rural highways is 5 metres (B) Minimum width of medians should be 3 metres (C) On long bridges and viaducts, the width of medians should be 1.5 m (D) All the above

Last Answer : Answer: Option D

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the possibility of tower wall collapse (B) Packed towers are preferred over plate towers for handling corrosive and foamy liquids (C) Diameter of randomly packed tower is normally more than 1.2 metres (D) Due to uneven supply and improper distribution of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Description : Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the ... of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Last Answer : (C) Diameter of randomly packed tower is normally more than 1.2 metres

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at A. Full depth B. Half full C. Two third full D. Three fourth full

Description : You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at A. Full depth B. Half full C. Two third full D. Three fourth full

Last Answer : ANS: B

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

Water flow rate in a pipe of 3.5 metres diameter can be most economically and conveniently measured by a/an (A) Pitot tube (B) Venturimeter (C) Orificemeter (D) Rotameter

Description : Water flow rate in a pipe of 3.5 metres diameter can be most economically and conveniently measured by a/an (A) Pitot tube (B) Venturimeter (C) Orificemeter (D) Rotameter

Last Answer : (A) Pitot tube

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) Deposition of calcium carbonate on the inside of the well pipe, causes incrustation of the pipe (B) Incrustation of the pipe reduces the discharge (C) Acidic waters cause corrosion of the pipes (D) All the above

Description : Pick up the correct statement from the following:  (A) Deposition of calcium carbonate on the inside of the well pipe, causes incrustation of the  pipe  (B) Incrustation of the pipe reduces the discharge  (C) Acidic waters cause corrosion of the pipes  (D) All the above 

Last Answer : (D) All the above 

Pick up the correct statement from the following: (A) Head loss in smaller size pipes at equal velocities, is less (B) Cost of pumping is less in smaller size pipes (C) Cost of smaller pipes is comparatively more (D) None of these

Description : Pick up the correct statement from the following:  (A) Head loss in smaller size pipes at equal velocities, is less  (B) Cost of pumping is less in smaller size pipes  (C) Cost of smaller pipes is comparatively more  (D) None of these 

Last Answer : (D) None of these 

Pick up the correct statement from the following: (A) Copper pipes are highly resistant to acidic and alkaline water (B) Wrought iron pipes are lighter than cast iron pipes (C) Wrought iron pipes corrode quickly and are less durable (D) All the above

Description : Pick up the correct statement from the following:  (A) Copper pipes are highly resistant to acidic and alkaline water  (B) Wrought iron pipes are lighter than cast iron pipes  (C) Wrought iron pipes corrode quickly and are less durable  (D) All the above

Last Answer : (D) All the above

The cross-sections for a highway is taken at (A) Right angle to the centre line (B) 30 metres apart (C) Intermediate points having abrupt change in gradient (D) All the above

Description : The cross-sections for a highway is taken at (A) Right angle to the centre line (B) 30 metres apart (C) Intermediate points having abrupt change in gradient (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) The eyepiece plays no part in defining the line of sight (B) The diaphragm plays no part in defining the line of sight (C) The optical centre of the objective plays no part in defining the line of sight (D) None of these

Description : Pick up the correct statement from the following: (A) The eyepiece plays no part in defining the line of sight (B) The diaphragm plays no part in defining the line of sight (C) The optical centre of the objective plays no part in defining the line of sight (D) None of these

Last Answer : (A) The eyepiece plays no part in defining the line of sight

0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre(B) In the standard rolled channels, the shear centre is on the horizontal line passing through and away from the C.G. beyond web (C) In equal angles, the shear centre is on the horizontal plane and away from the C.G., outside of the leg projection (D) All the above

Description : 0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre (B) In the standard rolled channels, the shear centre ... horizontal plane and away from the C.G., outside of the leg projection (D) All the above

Last Answer : (D) All the above

Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the item (B) The centre line is worked out separately for different sections of walls of a building (C) The centre line length is reduced by half the layer of main wall joining the partition wall (D) All the above

Description : Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the ... length is reduced by half the layer of main wall joining the partition wall (D) All the above

Last Answer : (D) All the above

Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Description : Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Last Answer : (D) All the above

If n is the ratio of internal and external diameters of a hollow shaft, the ratio of the weight of the hollow shaft and that of solid shaft of same strength, will be (A) (1 - n²)/(1 - n²)1/2 (B) (1 - n²)/(1 - n 4 )2/3 (C) (1 + n 3 )/(1 + n 4 )1/2 (D) (1 + n 1 )/(1 + n 4 )2/3

Description : If n is the ratio of internal and external diameters of a hollow shaft, the ratio of the weight of the  hollow shaft and that of solid shaft of same strength, will be  (A) (1 - n²)/(1 - n²)1/2 (B) (1 - n²)/(1 - n 4 ... (1 + n 4 )1/2 (D) (1 + n 1 )/(1 + n 4 )2/3

Last Answer : (B) (1 - n²)/(1 - n 4 )2/3

Pick up the correct statement from the following regarding the pressure conduits: (A) Pressure conduits are permitted to run ¾th full (B) Pressure conduits are always laid along down grades (C) The hydraulic gradient line always coincides the invert of the conduit (D) None of these

Description : Pick up the correct statement from the following regarding the pressure conduits:  (A) Pressure conduits are permitted to run ¾th full  (B) Pressure conduits are always laid along down grades  ... ) The hydraulic gradient line always coincides the invert of the conduit  (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed as the ratio of the concentration gradient at wall to the overall concentration difference (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2 (D) The z-component of the total mass flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Description : Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed ... flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Last Answer : (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

If the area calculated form the plan plotted with measurements by an erroneous chain, accurate area of the plan is (A) Measured area × (Length of chain used/Nominal chain length) (B) Measured area × (Nominal chain length/ Length of chain used) (C) Measured area × (Nominal chain length/ Length of chain used)² (D) Measured area × (Length of chain used/Nominal chain length)²

Description : If the area calculated form the plan plotted with measurements by an erroneous chain, accurate  area of the plan is  (A) Measured area (Length of chain used/Nominal chain length)  (B) Measured ... of chain used)²  (D) Measured area (Length of chain used/Nominal chain length)² 

Last Answer : (D) Measured area × (Length of chain used/Nominal chain length)² 

The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Description : The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Last Answer : (A) More

Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Last Answer : (D) None of these

The capacity of a spring to store energy is called the spring form coefficient. Stiffness of a spring is measured by the (A) Ability to absorb shock (B) Capacity to store energy (C) Ratio of the wire & coil diameters (D) Load to produce unit deflection

Description : The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the (A) Ability to absorb shock (B) Capacity to store energy (C) Ratio of the wire & coil diameters (D) Load to produce unit deflection

Last Answer : Option D

Pick out the wrong statement: (A) The vacuum pressure is always the negative gauge pressure (B) The pressure of the liquid measured by a piezometer tube is the gauge pressure (C) Manometric liquid should have high surface tension (D) The point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

Description : Pick out the wrong statement: (A) The vacuum pressure is always the negative gauge pressure (B) The pressure of the liquid measured by a piezometer tube is the gauge pressure (C) Manometric ... point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

Last Answer : (D) The point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD

Description : Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD

Last Answer : a) Power

Runoff is measured in (A) Cubic metres (B) Cubic metres per sec. (C) Cubic metres per minute (D) Cubic metres per hour

Description : Runoff is measured in (A) Cubic metres (B) Cubic metres per sec. (C) Cubic metres per minute (D) Cubic metres per hour

Last Answer : Answer: Option B