Consider two pipes of same length and diameter through which water is passed at the same velocity. The friction factor for rough pipe is f1 and that for smooth pipe is f2 . Pick out the correct statement(A) f1 = f2 (B) f1 < f2 (C) f1 > f2 (D) Data not sufficient to relate f1 & f2

Consider two pipes of same length and diameter through which water
is passed at the same velocity. The friction factor for rough pipe is f1 and
that for smooth pipe is f2
. Pick out the correct statement.
(A) f1 = f2
(B) f1 < f2
(C) f1 > f2
(D) Data not sufficient to relate f1 & f2
by

1 Answer

Answer :

(C) f1 > f2
by

Related questions

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

Friction factor for a hydraulically smooth pipe at NRe = 2100 is f1 . If the pipe is further smoothened (i.e., roughness is reduced), the friction factor at the same value of NRe , will (A) Increase (B) Decrease (C) Remain unchanged (D) Increase or decrease depending on the pipe material

Description : Friction factor for a hydraulically smooth pipe at NRe = 2100 is f1 . If the pipe is further smoothened (i.e., roughness is reduced), the friction factor at the same value of NRe , will (A) Increase (B) Decrease (C) Remain unchanged (D) Increase or decrease depending on the pipe material

Last Answer : (A) Increase

In the complete turbulence zone (in rough pipes), the (A) Rough and smooth pipes have the same friction factor (B) Laminar film covers the roughness projections (C) Friction factor depends upon NRe only (D) Friction factor is independent of the relative roughness

Description : In the complete turbulence zone (in rough pipes), the (A) Rough and smooth pipes have the same friction factor (B) Laminar film covers the roughness projections (C) Friction factor depends upon NRe only (D) Friction factor is independent of the relative roughness

Last Answer : (D) Friction factor is independent of the relative roughness

In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of the laminar film (C) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Description : In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of ... ) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Last Answer : (B) When the roughness projections are much smaller than the thickness of the laminar film

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Which of the following two quantities when same, makes one pipe system equivalent to another pipe system? (A) Head & discharge(B) Length & discharge(C) Length & diameter(D) Friction factor & diameter

Description : Which of the following two quantities when same, makes one pipe system equivalent to another pipe system? (A) Head & discharge (B) Length & discharge (C) Length & diameter (D) Friction factor & diameter

Last Answer : (A) Head & discharge

A compound pipe is required to be replaced by a new pipe. The two pipes are said to be equivalent, if (A) Length of both the pipes is same (B) Diameter of both the pipes is same (C) Loss of head and discharge of both the pipes is same (D) Loss of head and velocity of flow in both the pipes is same

Description : A compound pipe is required to be replaced by a new pipe. The two pipes are said to be equivalent, if (A) Length of both the pipes is same (B) Diameter of both the pipes is same (C) Loss of ... discharge of both the pipes is same (D) Loss of head and velocity of flow in both the pipes is same

Last Answer : Answer: Option C

Two pipe systems can be said to be equivalent, when the following quantities are same (A) Friction loss and flow (B) Length and diameter (C) Flow and length (D) Friction factor and diameter

Description : Two pipe systems can be said to be equivalent, when the following quantities are same (A) Friction loss and flow (B) Length and diameter (C) Flow and length (D) Friction factor and diameter

Last Answer : Answer: Option A

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Description : For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Last Answer : (A) Logarithmic

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

During ageing of fluid carrying pipes, the (A) Pipe becomes smoother with use (B) Friction factor increases linearly with time (C) Absolute roughness decreases with time (D) Absolute roughness increases linearly with time

Description : During ageing of fluid carrying pipes, the (A) Pipe becomes smoother with use (B) Friction factor increases linearly with time (C) Absolute roughness decreases with time (D) Absolute roughness increases linearly with time

Last Answer : (D) Absolute roughness increases linearly with time

Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m diameter are designed as running 2/3rd or 3/4th full at maximum discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Description : Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m ... discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Last Answer : ANS: D

The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Description : The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Last Answer : (A) Depends only on Reynolds number

A pipe is defined as 'hydraulically smooth', if the friction factor (A) Is not a function of Reynolds number (B) For a given Reynolds number remains constant even on further smoothening of the pipe (C) Is zero irrespective of the Reynolds number (D) None of these

Description : A pipe is defined as 'hydraulically smooth', if the friction factor (A) Is not a function of Reynolds number (B) For a given Reynolds number remains constant even on further smoothening of the pipe (C) Is zero irrespective of the Reynolds number (D) None of these

Last Answer : (B) For a given Reynolds number remains constant even on further smoothening of the pipe

For a given Reynolds number, in a hydraulically smooth pipe, further smoothening __________ the friction factor. (A) Brings about no further reduction of (B) Increases (C) Decreases (D) None of these

Description : For a given Reynolds number, in a hydraulically smooth pipe, further smoothening __________ the friction factor. (A) Brings about no further reduction of (B) Increases (C) Decreases (D) None of these

Last Answer : (A) Brings about no further reduction of

What is the value of Fanning friction factor f ' for smooth pipe at NRe = 10 6 approximately? (A) 0.003 (B) 0.01 (C) 0.1(D) 0.3

Description : What is the value of Fanning friction factor f ' for smooth pipe at NRe = 10 6 approximately? (A) 0.003 (B) 0.01 (C) 0.1 (D) 0.3

Last Answer : (A) 0.003

If f1 and f2 are the distances from the optical centre of a convex lens of focal length to conjugate two points P1 and P2 respectively, the following relationship holds good (A) f = f1 + f2 (B) f = ½ (f1 + f2) (C) 1/f = 1/f1 + 1/f2 (D) None of these

Description : If f1 and f2 are the distances from the optical centre of a convex lens of focal length to conjugate two points P1 and P2 respectively, the following relationship holds good (A) f = f1 + f2 (B) f = ½ (f1 + f2) (C) 1/f = 1/f1 + 1/f2 (D) None of these

Last Answer : (C) 1/f = 1/f1 + 1/f2

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to the shape of the particles, concrete aggregates are classified as rounded irregular, angular and flaky (C) According to the surface texture of the particles, the concrete aggregates are classified as glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Description : Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to ... glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Last Answer : Answer: Option D

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Description : Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Last Answer : (A) Fluid flow rate & friction loss

Transition length for turbulent flow in smooth pipe is equal to __________ times the pipe diameter. (A) 0.5 (B) 5 (C) 50 (D) 500

Description : Transition length for turbulent flow in smooth pipe is equal to __________ times the pipe diameter. (A) 0.5 (B) 5 (C) 50 (D) 500

Last Answer : (C) 50

Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Description : Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Last Answer : A) Pipe length

f we cross pure-bred tall (dominant) pea plant with pure-bred dwarf (recessive) pea plant we will get pea plants of F1 generation. If we now self-cross the pea plant of F2 generation, then we obtain pea plants of F2 generation. (a) What do the plants of F2 generation look like? (b) State the ratio of tall plants to dwarf plants in F2 generation. (c) State the type of plants not found in F2 generation but appeared in F2 generation, mentioning the reason for the same. -Biology

Description : f we cross pure-bred tall (dominant) pea plant with pure-bred dwarf (recessive) pea plant we will get pea plants of F1 generation. If we now self-cross the pea plant of F2 generation, ... plants not found in F2 generation but appeared in F2 generation, mentioning the reason for the same. -Biology

Last Answer : Answer. (a) All plants of F1 generation will be tall plants. (b) 3:1 (c) Dwarf trait is recessive trait which was not expressed in the F1 generation, the recessive trait gets expressed in the F2 generation after self pollination.

The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Description : The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The internal pressure within a pipe, is caused due to water head and hammer pressure (B) In pressure pipes with water at rest, the pressure is equal to water head (C) Sudden closure of a valve, causes the water hammer pressure (D) All the above

Description : Pick up the correct statement from the following:  (A) The internal pressure within a pipe, is caused due to water head and hammer pressure  (B) In pressure pipes with water at rest, the pressure ... (C) Sudden closure of a valve, causes the water hammer pressure  (D) All the above 

Last Answer : (D) All the above 

In case of end to end connection of two or more pipes in series, the __________ each pipe.(A) Same rate of flow passes through (B) Head loss is same through (C) Rate of flow in each pipe is proportional to the length of (D) Total flow rate is the sum of flow rate in

Description : In case of end to end connection of two or more pipes in series, the __________ each pipe. (A) Same rate of flow passes through (B) Head loss is same through (C) Rate of flow in each pipe is proportional to the length of (D) Total flow rate is the sum of flow rate in

Last Answer : (A) Same rate of flow passes through

Pick up the correct statement from the following: (A) Deposition of calcium carbonate on the inside of the well pipe, causes incrustation of the pipe (B) Incrustation of the pipe reduces the discharge (C) Acidic waters cause corrosion of the pipes (D) All the above

Description : Pick up the correct statement from the following:  (A) Deposition of calcium carbonate on the inside of the well pipe, causes incrustation of the  pipe  (B) Incrustation of the pipe reduces the discharge  (C) Acidic waters cause corrosion of the pipes  (D) All the above 

Last Answer : (D) All the above 

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

A pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/sec, the average velocity through the bifurcated pipes is (A) 20 m/sec (B) 10 m/sec (C) 5 √2 m/sec (D) 5 m/sec

Description : A pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/sec, the average velocity through the bifurcated pipes is (A) 20 m/sec (B) 10 m/sec (C) 5 √2 m/sec (D) 5 m/sec

Last Answer : (B) 10 m/sec

The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Description : The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Last Answer : (B) Less

A blue colour flower plant denoted by BB is cross bred with that of white colour flower plant denoted by bb. (a) State the colour of flower you would expect in their F1 generation plants. (b) What must be the percentage of white flower plants in F2 generation if flowers of F1 plants are self-pollinated? (c) State the expected ratio of the genotypes BB and Bb in the F2 progeny. -Biology

Description : A blue colour flower plant denoted by BB is cross bred with that of white colour flower plant denoted by bb. (a) State the colour of flower you would expect in their F1 generation plants. (b) What ... -pollinated? (c) State the expected ratio of the genotypes BB and Bb in the F2 progeny. -Biology

Last Answer : This is your Answer.

Difference of F1 generation and F2 generation. -Biology

Description : Difference of F1 generation and F2 generation. -Biology

Last Answer : answer:

Difference between the P generation F1 generation and F2 generation. -Biology

Description : Difference between the P generation F1 generation and F2 generation. -Biology

Last Answer : answer:

Which of the following layers of the ionosphere has no effect on sky wave propagation during daytime? A. D B. E C. F1 D. F2

Description : Which of the following layers of the ionosphere has no effect on sky wave propagation during daytime? A. D B. E C. F1 D. F2

Last Answer : A. D

What ionospheric layer has a daytime approximate critical frequency of 8 MHz? A. F2 layer B. F1 layer C. E layer D. D layer

Description : What ionospheric layer has a daytime approximate critical frequency of 8 MHz? A. F2 layer B. F1 layer C. E layer D. D layer

Last Answer : A. F2 layer

What ionospheric layer has a daytime approximate critical frequency of 8 MHz? A. F2 layer B. F1 layer C. E layer D. D layer

Description : What ionospheric layer has a daytime approximate critical frequency of 8 MHz? A. F2 layer B. F1 layer C. E layer D. D layer

Last Answer : A. F2 layer

During the night when the F2 layer combines with F1 layer it falls to what approximate height? A. 250 km B. 350 km C. 300 km D. 400 km

Description : During the night when the F2 layer combines with F1 layer it falls to what approximate height? A. 250 km B. 350 km C. 300 km D. 400 km

Last Answer : C. 300 km

Which if the following layers of the ionosphere has no effect on sky wave propagation during the hours of darkness? A. D B. E C. F1 D. F2

Description : Which if the following layers of the ionosphere has no effect on sky wave propagation during the hours of darkness? A. D B. E C. F1 D. F2

Last Answer : A. D

At height about 180 km above the earth exist only during daylight. A. F2 layer B. D layer C. E layer D. F1 layer

Description : At height about 180 km above the earth exist only during daylight. A. F2 layer B. D layer C. E layer D. F1 layer

Last Answer : D. F1 layer

What is the thickest layer of the ionosphere? A. E B. F1 C. F2 D. D

Description : What is the thickest layer of the ionosphere? A. E B. F1 C. F2 D. D

Last Answer : C. F2

ECE Board Exam March 1996 The lowest layer in the ionosphere A. D B. F2 C. E D. F1

Description : ECE Board Exam March 1996 The lowest layer in the ionosphere A. D B. F2 C. E D. F1

Last Answer : A. D

On selfing a plant of F1-generation with genotype “AABbCC”, the genotypic ratio in F2-generation will be (a) 3 : 1 (b) 1 : 1 (c) 9 : 3 : 3 : 1 (d) 27 : 9 : 9 : 9 : 3 : 3 : 3 : 1.

Description : On selfing a plant of F1-generation with genotype “AABbCC”, the genotypic ratio in F2-generation will be (a) 3 : 1 (b) 1 : 1 (c) 9 : 3 : 3 : 1 (d) 27 : 9 : 9 : 9 : 3 : 3 : 3 : 1.

Last Answer : (a) 3 : 1

A common test to find the genotype of a hybrid is by (a) crossing of one F2 progeny with female parent (b) studying the sexual behaviour of F1 progenies (c) crossing of one F1 progeny with male parent (d) crossing of one F2 progeny with male parent

Description : A common test to find the genotype of a hybrid is by (a) crossing of one F2 progeny with female parent (b) studying the sexual behaviour of F1 progenies (c) crossing of one F1 progeny with male parent (d) crossing of one F2 progeny with male parent

Last Answer : (c) crossing of one F1 progeny with male parent

In Antirrhinum (Snapdragon), a red flower was crossed with a white flower and in F1 generation all pink flowers were obtained. When pink flowers were selfed, the F2 generation showed white, red and pink flowers. Choose the incorrect statements from the following. (a) Law of segregation does not apply in this experiment. (b) This experiment does not follow the Principle of Dominance. (c) Pink colour in F1 is due to incomplete dominance. (d) Ratio of F2 is 1 4 2 4 1 4 ( ) red p : ( ink w ) : ( ) hite .

Description : In Antirrhinum (Snapdragon), a red flower was crossed with a white flower and in F1 generation all pink flowers were obtained. When pink flowers were selfed, the F2 generation showed white, red and pink flowers. Choose the incorrect ... F2 is 1 4 2 4 1 4 ( ) red p : ( ink w ) : ( ) hite .

Last Answer : (a) Law of segregation does not apply in this experiment.

For a charge Q1, the effect of charge Q2 on Q1 will be, a) F1 = F2 b) F1 = -F2 c) F1 = F2 = 0 d) F1 and F2 are not equal

Description : For a charge Q1, the effect of charge Q2 on Q1 will be, a) F1 = F2 b) F1 = -F2 c) F1 = F2 = 0 d) F1 and F2 are not equal

Last Answer : b) F1 = -F2

Short Cut key for Print Preview is: a) Ctrl + F2 b) Ctrl + F3 c) Ctrl + F1 d) None of These

Description : Short Cut key for Print Preview is: a) Ctrl + F2 b) Ctrl + F3 c) Ctrl + F1 d) None of These

Last Answer : a) Ctrl + F2

Which key on the key board can be used to view slide show: a) F1 b) F2 c) F5 d) F10 e) None of The Above

Description : Which key on the key board can be used to view slide show: a) F1 b) F2 c) F5 d) F10 e) None of The Above

Last Answer : c) F5