Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these
Last Answer : (A) - 0.000909 m
Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2
Last Answer : [ A ] 2 x 105 N/mm2
Description : The modules of elasticity of steel shall be taken as (a) 100kN/mm2 (b) 200 kN/mm2 (c) 250 kN/mm2 (d) 300 kN/mm2
Last Answer : (b) 200 kN/mm2
Description : Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)? (A) High speed steel (B) Stainless steel (C) Tungsten carbide (D) Superalloys
Last Answer : (C) Tungsten carbide
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm
Last Answer : Answer: Option D
Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)
Last Answer : Answer: Option B
Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm
Last Answer : (D) 5 mm
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : Approximate value of the modulus of elasticity for steel is about __________ × 10 6kg/cm2 . (A) 0.5 (B) 2 (C) 40 (D) 75
Last Answer : (B) 2
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The extension in the rod was 1 mm only. If Esteel = 2 × 106 kg/cm2 , the side of the rod, is (A) 1 cm (B) 1.5 cm (C) 2 cm (D) 2.5 cm
Last Answer : (C) 2 cm
Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg
Last Answer : (B) 102 kg
Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK
Last Answer : [ B ] 5000 vfCK
Description : Minimum grade of concrete to be used in reinforced concrete as per IS: 4561978 is (A) M 15 (B) M 20 (C) M 10 (D) M 25
Last Answer : Answer: Option A
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm
Last Answer : Answer: Option C
Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3
Last Answer : 1,2,4
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm
Last Answer : b. 105.4 mm
Description : If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good (A) E = 3K (1 - 2/m) (B) E = 2N (1 + 1/m) (C) (3/2)K (1 - 2/m) = N (1 + 1/m) (D) All the above
Last Answer : (D) All the above
Description : The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4
Last Answer : a) 7
Description : A normally consolidated clay settled 10 mm when effective stress was increased from 100 kN/m² to 200 kN/m². If the effective stress is further increased from 200 kN/m² to 400 kN/m², then the settlement of the same clay is (A) 10 mm (B) 20 mm (C) 40 mm (D) None of the above
Last Answer : (A) 10 mm
Description : The specific weight of water in S.I. units is taken as (A) 9.81 kN/m3 (B) 9.81 × 103 N/m3 (C) 9.81 × 10-6 N/mm3 (D) Any one of these
Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm
Description : The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3
Last Answer : (C) N/m2
Description : For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m
Last Answer : (B) ∞ N/m2
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2
Last Answer : : Option B
Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm
Last Answer : (C) 50 mm
Description : During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26 N/mm², the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². Skempton's pore B (A) 0.5 (B) -0.5 (C) 2.0 (D) -2.0
Last Answer : (A) 0.5
Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°
Description : The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2
Description : Crushing strength of a first class brick should not be less than (A) 3.5 N/mm² (B) 7.0 N/mm² (C) 10.5 N/mm² (D) 14.0 N/mm²
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)
Last Answer : (D) Both (a) and (b)
Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F
Last Answer : (C) M/I = E/R = E/Y
Description : Euler's formula states that the buckling load for a column of length , both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are and respectively, is given by the relation (A) P = ²EI/l² (B) P = /EI (C) P = /l² (D) P = ²EI/l
Last Answer : (A) P = ²EI/l²
Description : The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity
Description : bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases
Description : (A) Absolute temperature (B) Temperature (C) Density (D) Modulus of elasticity
Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members
Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete
Description : Which of the following statements refer to correct purpose as regards testing of concrete by ultrasonic pulse velocity method? 1. To assess the quality of concrete in-situ. 2. To determine the dynamic modulus of elasticity of concrete. 3 ... and 2 only (b) 1 and 3 only (c) 2 and 3 only (d)1, 2 and 3
Last Answer : (d)1, 2 and 3
Description : Modulus of elasticity of concrete is increased with (a) Higher W/C ratio (b) Shorter curing period (c) Lesser vibration (d) Increase in age
Last Answer : (d) Increase in age
Description : Modulus of elasticity of concrete is primarily influenced by [ A ] Elastic properties of aggregate [ B ] Curing of concrete [ C ] Age of concrete [ D ] Mix proportion and type of cement
Last Answer : [ A ] Elastic properties of aggregate
Description : For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30
Last Answer : (C) 0.25
Description : If the price of burger rises from `12 per piece to `20 per piece as a result of which the daily sales decreases from 300 to 200 pieces per day. The price elasticity of demand can be estimated as (a) 0.5 ; (b) 0.8 ; (c) 0.25 ; (d) 2.10
Last Answer : (a) 0.5 ;