The ratio of average fluid velocity to the maximum velocity in case of laminar flow of a Newtonian fluid in a circular pipe is (A) 0.5 (B) 1 (C) 2 (D) 0.66

The ratio of average fluid velocity to the maximum velocity in case of
laminar flow of a Newtonian fluid in a circular pipe is
(A) 0.5
(B) 1
(C) 2
(D) 0.66
by

1 Answer

Answer :

(A) 0.5
by

Related questions

For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Last Answer : (B) 1

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

What is the ratio of total kinetic energy of fluid passing per second to the value obtained on the basis of average velocity (for laminar flow through a circular pipe)? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Description : What is the ratio of total kinetic energy of fluid passing per second to the value obtained on the basis of average velocity (for laminar flow through a circular pipe)? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Last Answer : (D) 2

For laminar flow of Newtonian fluid in a circular pipe, the velocitydistribution is a function of the distance 'd' measured from the centre line ofthe pipe, and it follows a __________ relationship.(A) Logarithmic(B) Parabolic(C) Hyperbolic(D) Linear

Description : For laminar flow of Newtonian fluid in a circular pipe, the velocitydistribution is a function of the distance 'd' measured from the centre line of the pipe, and it follows a __________ relationship. (A) Logarithmic (B) Parabolic (C) Hyperbolic (D) Linear

Last Answer : (B) Parabolic

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Description : In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Last Answer : (B) 1.2 Vavg

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Description : Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

. In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with increasing Reynolds number (C) Point of maximum instability exists at a distance of 2r/3 from the pipe wall (r = pipe radius) (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Description : . In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with ... , shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Last Answer : (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

The Nusselt number for fully developed (both thermally and hydrodynamically) laminar flow through a circular pipe whose surface temperature remains constant is (A) 1.66(B) 88.66 (C) 3.66 (D) Dependent on NRe only

Description : The Nusselt number for fully developed (both thermally and hydrodynamically) laminar flow through a circular pipe whose surface temperature remains constant is (A) 1.66 (B) 88.66 (C) 3.66 (D) Dependent on NRe only

Last Answer : (C) 3.66

The maximum discharge through a circular channel takes place, when the depth of the fluid flow is __________ times the pipe diameter. (A) 0.25 (B) 0.5 (C) 0.66 (D) 0.95

Description : The maximum discharge through a circular channel takes place, when the depth of the fluid flow is __________ times the pipe diameter. (A) 0.25 (B) 0.5 (C) 0.66 (D) 0.95

Last Answer : (D) 0.95

Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Description : Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Last Answer : (B) 2100

The ratio of the hydraulic radius to the diameter of the channel, for maximum mean velocity of flow in a circular channel, in open channel flow is (A) 0.3 (B) 0.9 (C) 0.03 (D) 0.66

Description : The ratio of the hydraulic radius to the diameter of the channel, for maximum mean velocity of flow in a circular channel, in open channel flow is (A) 0.3 (B) 0.9 (C) 0.03 (D) 0.66

Last Answer : (A) 0.3

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

The kinetic energy correction factor for velocity distribution of laminar flow is (A) 0.5 (B) 1.66 (C) 1 (D) 2

Description : The kinetic energy correction factor for velocity distribution of laminar flow is (A) 0.5 (B) 1.66 (C) 1 (D) 2

Last Answer : (B) 1.66

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

The momentum correction factor for the velocity distribution of laminar flow is (A) 1.3 (B) 1.66 (C) 2.5 (D) None of these

Description : The momentum correction factor for the velocity distribution of laminar flow is (A) 1.3 (B) 1.66 (C) 2.5 (D) None of these

Last Answer : (D) None of these

The Nusselt number for fully developed (both thermally and hydrodynamically) laminar flow through a circular pipe, where the wall heat flux is constant, is(A) 2.36(B) 4.36(C) 120.36(D) Dependent on NRe only

Description : The Nusselt number for fully developed (both thermally and hydrodynamically) laminar flow through a circular pipe, where the wall heat flux is constant, is (A) 2.36 (B) 4.36 (C) 120.36 (D) Dependent on NRe only

Last Answer : (B) 4.36

The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Description : The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Last Answer : (D) Parabolic near the wall and flat in the middle

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Where does the maximum stress occur in case of laminar flow of incompressible fluid in a closed conduit of diameter 'd'? (A) At the centre (B) At d/4 from the wall (C) At the wall (D) At d/8 from the wall

Description : Where does the maximum stress occur in case of laminar flow of incompressible fluid in a closed conduit of diameter 'd'? (A) At the centre (B) At d/4 from the wall (C) At the wall (D) At d/8 from the wall

Last Answer : (C) At the wall

The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Description : The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Last Answer : (D) Nu, Gz

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Description : The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Last Answer : (C) 1/A

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Description : The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Last Answer : (A) Parabolic

Experimental study of laminar fluid flow through a circular tube was conducted by(A) Reynolds(B) Hagen and Poiseuille(C) Pascal(D) Blake-Plummer

Description : Experimental study of laminar fluid flow through a circular tube was conducted by (A) Reynolds (B) Hagen and Poiseuille (C) Pascal (D) Blake-Plummer

Last Answer : (B) Hagen and Poiseuille

The distribution of shear stress in a stream of fluid in a circular tube is(A) Linear with radius for turbulent flow only(B) Linear with radius for laminar flow only(C) Linear with radius for both laminar & turbulent flow(D) Parabolic with radius for both laminar & turbulent flow

Description : The distribution of shear stress in a stream of fluid in a circular tube is (A) Linear with radius for turbulent flow only (B) Linear with radius for laminar flow only (C) Linear with radius for both laminar & turbulent flow (D) Parabolic with radius for both laminar & turbulent flow

Last Answer : (C) Linear with radius for both laminar & turbulent flow

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Description : Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Last Answer : (C) 66.6

The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Description : The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Last Answer : (A) Area of surface in contact

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Description : For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Last Answer : (A) Decreases

What is the ratio of the velocity at the axis of the pipe to the mean velocity of flow in case of pipe flow under viscous condition? (A) 0.5 (B) 0.67 (C) 1 (D) 2

Description : What is the ratio of the velocity at the axis of the pipe to the mean velocity of flow in case of pipe flow under viscous condition? (A) 0.5 (B) 0.67 (C) 1 (D) 2

Last Answer : (D) 2

In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is (A) The velocity of sound (B) Dependent on its cross-sectional area (C) Dependent on fluid viscosity (D) Dependent on fluid density

Description : In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is (A) The velocity of sound (B) Dependent on its cross-sectional area (C) Dependent on fluid viscosity (D) Dependent on fluid density

Last Answer : (A) The velocity of sound

In fluid flow, the boundary layer separation cannot occur (A) In case of boundaries experiencing form drag (B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of these

Description : In fluid flow, the boundary layer separation cannot occur (A) In case of boundaries experiencing form drag (B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of theseIn ... B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of these

Last Answer : (D) None of these

Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%? (A) 9,100 (B) 13,000 (C) 7,000 (D) 2,550

Description : Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%? (A) 9,100 (B) 13,000 (C) 7,000 (D) 2,550

Last Answer : (A) 9,100

The ratio of maximum to average velocity in case of streamline flow between parallel plates is (A) 1 (B) 1.5 (C) 2 (D) 2.5

Description : The ratio of maximum to average velocity in case of streamline flow between parallel plates is (A) 1 (B) 1.5 (C) 2 (D) 2.5

Last Answer : (B) 1.5

The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Description : The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Last Answer : (B) Newtonian

A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Description : A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Last Answer : (C) Directly proportional to

Nusselt number for full developed, laminar, constant property flow in a pipe at uniform heat flux is (A) 0.72 (B) 4.364 (C) 18 (D) 83

Description : Nusselt number for full developed, laminar, constant property flow in a pipe at uniform heat flux is (A) 0.72 (B) 4.364 (C) 18 (D) 83

Last Answer : (B) 4.364

A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Last Answer : (A) 7