In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is (A) The velocity of sound (B) Dependent on its cross-sectional area (C) Dependent on fluid viscosity (D) Dependent on fluid density

In case of a pipe of constant cross-sectional area, the maximum fluid
velocity obtainable is
(A) The velocity of sound
(B) Dependent on its cross-sectional area
(C) Dependent on fluid viscosity
(D) Dependent on fluid density
by

1 Answer

Answer :

(A) The velocity of sound
by

Related questions

Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: (1) increases (2) decreases (3) stays the same (4) none of the above

Description : Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: (1) increases (2) decreases (3) stays the same (4) none of the above

Last Answer : (1) increases

Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: w) increases x) decreases y) stays the same

Description : Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: w) increases x) decreases y) stays the same

Last Answer : ANSWER: W -- INCREASES 

The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Last Answer : (A) 3.6 AVS.ρ

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Description : The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Last Answer : (C) 1/A

The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Description : The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Last Answer : (A) Parabolic

Pressure gradient in the pipe flow is influenced by the (A) Diameter of pipe (B) Velocity of the fluid (C) Density & viscosity of the fluid (D) All (A), (B) and (C)

Description : Pressure gradient in the pipe flow is influenced by the (A) Diameter of pipe (B) Velocity of the fluid (C) Density & viscosity of the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Critical velocity in a pipe flow (A) Increases as fluid viscosity increases (B) Increases as pipe diameter increases (C) Independent of fluid density (D) None of these

Description : Critical velocity in a pipe flow (A) Increases as fluid viscosity increases (B) Increases as pipe diameter increases (C) Independent of fluid density (D) None of these

Last Answer : (B) Increases as pipe diameter increases

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

With diminishing cross-sectional area in case of subsonic flow in a converging nozzle, the (A) Velocity increases (B) Pressure decreases (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : With diminishing cross-sectional area in case of subsonic flow in a converging nozzle, the (A) Velocity increases (B) Pressure decreases (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Description : Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Last Answer : 0.015 mm s-1

For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Last Answer : (B) 1

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Description : Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Last Answer : (A) Type of orifice

Optimum economic pipe diameter for fluid is determined by the (A) Viscosity of the fluid (B) Density of the fluid (C) Total cost considerations (pumping cost plus fixed cost of the pipe) (D) None of these

Description : Optimum economic pipe diameter for fluid is determined by the (A) Viscosity of the fluid (B) Density of the fluid (C) Total cost considerations (pumping cost plus fixed cost of the pipe) (D) None of these

Last Answer : (C) Total cost considerations (pumping cost plus fixed cost of the pipe)

Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Description : Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Last Answer : A) Pipe length

The ratio of average fluid velocity to the maximum velocity in case of laminar flow of a Newtonian fluid in a circular pipe is (A) 0.5 (B) 1 (C) 2 (D) 0.66

Description : The ratio of average fluid velocity to the maximum velocity in case of laminar flow of a Newtonian fluid in a circular pipe is (A) 0.5 (B) 1 (C) 2 (D) 0.66

Last Answer : (A) 0.5

In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Description : In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Last Answer : (B) 1.2 Vavg

. In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with increasing Reynolds number (C) Point of maximum instability exists at a distance of 2r/3 from the pipe wall (r = pipe radius) (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Description : . In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with ... , shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Last Answer : (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Description : The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Last Answer : Answer: D

Hydraulic mean radius is A. Mean radius of sewer B. Difference in heads between two points in circular pipes C. Mean of radii in a pipe line of varying cross -sections D. Cross-sectional area/wetted perimeter

Description : Hydraulic mean radius is A. Mean radius of sewer B. Difference in heads between two points in circular pipes C. Mean of radii in a pipe line of varying cross -sections D. Cross-sectional area/wetted perimeter

Last Answer : ANS: D

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Description : Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section(B) Remains constant over the cross-section(C) Is zero at the centre and varies linearly with the radius(D) Is zero at the wall and increases linearly to the centre

Description : Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section (B) Remains constant over the cross-section (C) Is zero at the centre and varies linearly with the radius (D) Is zero at the wall and increases linearly to the centre

Last Answer : (C) Is zero at the centre and varies linearly with the radius

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

The Bernoulli's equation is based on the assumption that (A) There is no loss of energy of the liquid flowing (B) The velocity of flow is uniform across any cross-section of the pipe (C) No force except gravity acts on the fluid (D) All of the above

Description : The Bernoulli's equation is based on the assumption that (A) There is no loss of energy of the liquid flowing (B) The velocity of flow is uniform across any cross-section of the pipe (C) No force except gravity acts on the fluid (D) All of the above

Last Answer : Answer: Option D

When a small spherical body falls in a viscous fluid, its speed increases first, then deceases and eventually it acquires a constant speed called the terminal speed. The terminal speed depends upon (a) The density and viscosity of the fluid (b) The density of the body (c) The diameter of the body (d) All the above parameters

Description : When a small spherical body falls in a viscous fluid, its speed increases first, then deceases and eventually it acquires a constant speed called the terminal speed. The terminal speed depends upon (a) The ... ) The density of the body (c) The diameter of the body (d) All the above parameters

Last Answer : Ans:(d)

What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^(2)` if the current is 10 A. Assume there

Description : What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^(2)` if the current is 10 A. Assume there

Last Answer : What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^( ... `8.0xx10^(28) "electrons"//m^(3)`.

The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10^(-4) m//s` when a certain potential differ

Description : The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10^(-4) m//s` when a certain potential differ

Last Answer : The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10 ... is `8.5xx10^(28) "electrons"//m^(3)`.

A current of 4.8 A is flowing in a copper wire of cross-sectional area `3xx10^(-4) m^(2)`. Find the current density in the wire.

Description : A current of 4.8 A is flowing in a copper wire of cross-sectional area `3xx10^(-4) m^(2)`. Find the current density in the wire.

Last Answer : A current of 4.8 A is flowing in a copper wire of cross-sectional area `3xx10^(-4) m^(2)`. Find the current density in the wire.

A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the density of the charge-carriers in the wire

Description : A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the density of the charge-carriers in the wire

Last Answer : A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the ... ms^(-1)` D. `1xx10^(-2)ms^(-1)`

E.M.F for a coil depends upon A. the cross sectional area B. no. of turns of wire C. the magnitude of magnetic flux density D. all of above

Description : E.M.F for a coil depends upon A. the cross sectional area B. no. of turns of wire C. the magnitude of magnetic flux density D. all of above

Last Answer : all of above

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Description : Capacity of field choppers (chaff cutter) is affected by (a)capacity of the feed mechanism (cross sectional area) (b)Rate of advance of material through throat considered as to be the same linear speed of feed mechanism (c) density of forage material (d) all of the above

Last Answer : (d) all of the above

If the cross-sectional area of a magnetic field increases, but the flux remains the same, the flux density:

Description : If the cross-sectional area of a magnetic field increases, but the flux remains the same, the flux density: A. increases B. decreases C. remains the same D. doubles

Last Answer : If the cross-sectional area of a magnetic field increases, but the flux remains the same, the flux density: decreases

Deformation drag, which is caused by widespread deformation of fluid around the immersed body(A) Occurs when NReis very small(B) Is primarily a friction drag(C) Is independent of body length(D) Depends mainly on cross-sectional shape

Description : Deformation drag, which is caused by widespread deformation of fluid around the immersed body (A) Occurs when NRe is very small (B) Is primarily a friction drag (C) Is independent of body length (D) Depends mainly on cross-sectional shape

Last Answer : (A) Occurs when NRe is very small

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Description : The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Last Answer : (C) Represents the conservation of mass

____________ is the average rate of transmission of sound energy in a given direction through a cross sectional area of 1 sq.m. at right angle to the direction. A. Sound pressure B. Sound intensity C. Pressure variation D. Loudness

Description : ____________ is the average rate of transmission of sound energy in a given direction through a cross sectional area of 1 sq.m. at right angle to the direction. A. Sound pressure B. Sound intensity C. Pressure variation D. Loudness

Last Answer : B. Sound intensity

In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Last Answer : A.Greater then 100%