Excessive noise in operation/ Compressor make noise

Excessive noise in operation/ Compressor make noise
by

1 Answer

Answer :

Causes
remedial action
1. Loose pulley, flywheel, belt, belt guard, cooler, clamps or accessories.
Tighten any loose ends.
2. Lack of oil in crankcase.
Check for possible damage to bearings Replenish the oil level.
3. Piston hitting the valve plate.
Remove the compressor cylinder head and inspect for foreign matter on top of the piston. Add a new gasket and reassemble the head.
4. Compressor floor mounting loose.
Tighten the bolts on the air compressor. It may also be a good idea to replace your vibration pads
5. Defective crankcase.
Repair or replace.
by

Related questions

Difference between Single stage compressor and Multi stage compressor.

Description : Difference between Single stage compressor and Multi stage compressor.

Last Answer : Single stage compressor Multi stage compressor. Only one cylinder for the compressor process More than one cylinder is connected in series Used in low pressure application Achieve a very ... low Suitable for light task Suitable for heavy task. It can manage large load

The basic difference between compressor and pump is

Description : The basic difference between compressor and pump is

Last Answer : A pump is a machine that moves a fluid either liquid or gas from one place to another. A compressor is a machine that compresses a gas into a smaller volume.

Working of Double Acting Reciprocating Pump

Description : Working of Double Acting Reciprocating Pump

Last Answer : Working of Double Acting Reciprocating Pump As the piston moves to the right hand side as shown in the fig above. The following process takes place at left and right side. At left ... same time. If suction is taking place at right side than discharge takes place at left and vice-versa.

Difference between Impulse turbine and Reaction turbine.

Description : Difference between Impulse turbine and Reaction turbine.

Last Answer : Impulse turbine Reaction turbine 1. Steam completely expands in nozzle and pressure remains constant during flow through the blade passage.2. Relative velocity of steam passing over blade of impulse ... more space per unit power. 6.The blades are aerofoil & non symmetrical type.

Faults and remedies for less efficiency of I C engine

Description : Faults and remedies for less efficiency of I C engine

Last Answer : 1. The air intake might be clogged, so there is fuel but not enough air - clean/ replace air filter 2. The fuel system might be supplying too much or too little fuel to the mix, meaning that combustion ... If your sparkplug or the wire leading to it is worn out, the spark will be weak - replace it

Classification of pumps

Description : Classification of pumps 

Last Answer : A) Centrifugal pumps 1- Axial flow pump 2- Radial flow pump  B) Positive displacement pumps 1- Rotary gear pump 2- Rotary vane pump 3- Rotary lobe pump 4- Rotary screw pump 5- Reciprocating pump

BENSON BOILER

Description : BENSON BOILER

Last Answer : It is a water tube boiler capable of generating steam at supercritical pressure. Figure shows the schematic of Benson boiler. Mark Benson, 1992 conceived the idea of generating steam at supercritical pressure in ... 135 tons/hr. Thermal efficiency of these boilers is of the order of 90%.

Seasonal efficiency

Description : Seasonal efficiency

Last Answer : Seasonal efficiency is how well the boiler uses fuel over the entire heating season. It is the ratio of the total seasonal heat output used by the facility to the total seasonal fuel input. The seasonal efficiency depends on the boiler’s steady-state efficiency, standby losses, and cycling losses. 

Boiler efficiency

Description : Boiler efficiency

Last Answer : Boiler efficiency is the fraction of energy input that actually goes into raising steam. Thus it could be given by the ratio of heat actually used for steam generation and total heat available due to combustion of fuel in boiler.

Provisions under boiler act for remedial measures are

Description : Provisions under boiler act for remedial measures are

Last Answer : No owner of a boiler shall use the boiler or permit it to be used  1. Unless it has been registered in accordance with the provision of this act 2. In the case of any boiler which ... or competency unless the boiler is in charge of a person holding the certificate required by such rules.

Classification of I.C. engines on the basis of

Description : Classification of I.C. engines on the basis of

Last Answer : 1) Method of ignition – Spark ignition engine, Compression ignition engine 2) Thermodynamic cycle – Otto cycle engine, diesel cycle engine, Dual cycle engine 

Application of pump

Description : Application of pump

Last Answer : 1. Pumping water from wells, aquarium filtering, pond filtering and aeration 2. In the car industry for water-cooling and fuel injection 3. In the energy industry for pumping oil and natural gas ... pumps and in various hydraulic power packs 9. Car washes often use these triplex-style plunger pumps

Following are the different power losses in steam turbine.

Description : Following are the different power losses in steam turbine. 

Last Answer : 1) Residual velocity loss 2) Losses in regulating valves 3) Loss due to steam friction in nozzle. 4) Loss due to leakage 5) Loss due to mechanical frication 6) Loss due to wetness of steam 7) Radiation loss 8) Losses in exhaust piping

Following are the applications of compressed air in industry

Description : Following are the applications of compressed air in industry 

Last Answer : 1) To drive air motors in coal mines. 2) To inject fuel in air injection diesel engines. 3) To operate pneumatic drills, hammers, hoists, sand blasters. 4) For cleaning purposes. 5) To cool large ... ) To operate air tools like air guns. 10) To hold & index cutting tools on machines like milling.

Window cracks with excessive noise

Description : Is it theoretically possible for a thin glass window to break in the barracks with really loud music at home? We don't have plastic windows yet and I'm afraid the window panel will spill out.

Last Answer : Of course, if the noise is really loud, the window may crack.

A control system with excessive noise, is likely to suffer from (a) saturation in amplifying stages (b) loss of gain (c) vibrations (d) oscillations

Description : A control system with excessive noise, is likely to suffer from (a) saturation in amplifying stages (b) loss of gain (c) vibrations (d) oscillations

Last Answer : Ans: A

A loud buzzing noise coming from the contacts in a magnetic controller can be caused by ____________. A. excessive current B. excessive magnet gap C. bouncing of contacts D. dirt on magnet faces

Description : A loud buzzing noise coming from the contacts in a magnetic controller can be caused by ____________. A. excessive current B. excessive magnet gap C. bouncing of contacts D. dirt on magnet faces

Last Answer : Answer: D

A loud buzzing noise at the contacts of a magnetic controller could indicate _____________. A. weak contact spring pressure B. misalignment of the magnet faces C. excessive line current D. mechanical binding

Description : A loud buzzing noise at the contacts of a magnetic controller could indicate _____________. A. weak contact spring pressure B. misalignment of the magnet faces C. excessive line current D. mechanical binding

Last Answer : Answer: B

A man exposed to excessive noise level in the working environment may suffer from (A) Hearing loss (B) Rupture of ear drum (C) Nervousness & fatigue (D) All (A), (B) & (C)

Description : A man exposed to excessive noise level in the working environment may suffer from (A) Hearing loss (B) Rupture of ear drum (C) Nervousness & fatigue (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

What are the possible causes of excessive vibration or noise in a steam turbine?

Description : What are the possible causes of excessive vibration or noise in a steam turbine?

Last Answer : 1. Misalignment. 2. Worn bearings. 3. Worn coupling to driven machine. 4. Unbalanced coupling to driven machine. 5. Unbalanced wheel. 6. Piping strain. 7. Bent shaft.

How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Description : How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Last Answer : 1. The inlet as well as exhaust steam lines should be firmly supported to avoid strains from being imposed on the turbine. 2. Adequate allowance should be made for expansion of steam pipes due to heat.

A control system with excessive noise, is likely to suffer from?

Description : A control system with excessive noise, is likely to suffer from?

Last Answer : A control system with excessive noise, is likely to suffer from saturation in amplifying stages.

Which of the following processes cannot be made reversible even under ideal condition of operation? (A) Free expansion of a gas (B) Compression of air in a compressor (C) Expansion of steam in a turbine (D) All (A), (B) & (C)

Description : Which of the following processes cannot be made reversible even under ideal condition of operation? (A) Free expansion of a gas (B) Compression of air in a compressor (C) Expansion of steam in a turbine (D) All (A), (B) & (C)

Last Answer : (A) Free expansion of a gas

What are the limitations of a centrifugal compressor operation?

Description : What are the limitations of a centrifugal compressor operation? 

Last Answer : The major limitation of a centrifugal compressor is that is operates at peak efficiency at design point only and any deviation from the operating point is detrimental to its performance. When selecting ... at high pressure, with the consequent reduction in flow, the surge point is not reached.

From base load operation and from achieving best specific energy consumption point of view, which of the following compressors are suitable? a) Single stage reciprocating compressors b) Centrifugal compressors c) Two stage reciprocating compressor d) Multi stage reciprocating compressor

Description : From base load operation and from achieving best specific energy consumption point of view, which of the following compressors are suitable? a) Single stage reciprocating compressors b) Centrifugal compressors c) Two stage reciprocating compressor d) Multi stage reciprocating compressor

Last Answer : b) Centrifugal compressors

From the point of lower specific energy consumption, which of the following compressors are suitable for part load operation? a) Two stage reciprocating compressors b) Centrifugal compressors c) Two stage screw compressor d) Single stage screw compressor

Description : From the point of lower specific energy consumption, which of the following compressors are suitable for part load operation? a) Two stage reciprocating compressors b) Centrifugal compressors c) Two stage screw compressor d) Single stage screw compressor

Last Answer : a) Two stage reciprocating compressors

Uneven wear of the commutator surface on a direct current propulsion motor can be caused by _____________. A. rapid change in load B. excessive operation at light load C. incorrect brush staggering D. unequal pole spacing

Description : Uneven wear of the commutator surface on a direct current propulsion motor can be caused by _____________. A. rapid change in load B. excessive operation at light load C. incorrect brush staggering D. unequal pole spacing

Last Answer : Answer: C

In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Description : Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Last Answer : Answer: B

When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Description : When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Last Answer : Answer: C

Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Description : Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Last Answer : Answer: B

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

Which of the following refers to theterms "residual error rate"? A. the number of biterrors per twenty four hours of continuous operation onanasynchronous line B. The probability that one or moreerrors will be undetected whenan error detection scheme is used C. the probability thatone or more errors will bedetected when anerror detection mechanism is used D. signal tonoise ratio dividedby the ratio of energy perbit to noise per hertz E. None of the above

Description : Which of the following refers to theterms "residual error rate"? A. the number of biterrors per twenty four hours of continuous operation onanasynchronous line B. The probability that one or moreerrors ... tonoise ratio dividedby the ratio of energy perbit to noise per hertz E. None of the above

Last Answer : The probability that one or moreerrors will be undetected whenan error detection scheme is used

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

High noise levels produced during operation of fans and compressors can be reduced by using (A) Mufflers (silencers) (B) Acoustic absorbent (C) Lagging of noisy duct (D) None of these

Description : High noise levels produced during operation of fans and compressors can be reduced by using (A) Mufflers (silencers) (B) Acoustic absorbent (C) Lagging of noisy duct (D) None of these

Last Answer : (A) Mufflers (silencers)

Switching of a lamp in house produces noise in the radio. This is because switching operation produces?

Description : Switching of a lamp in house produces noise in the radio. This is because switching operation produces?

Last Answer : Switching of a lamp in house produces noise in the radio. This is because switching operation produces arcs across separating contacts.

Why Does The Safety Valve On My Compressor Pump Make A "popping" Sound?

Description : Why Does The Safety Valve On My Compressor Pump Make A "popping" Sound?

Last Answer : This is most commonly an indication of bad valves. Depending on the model valves could be rebuilt or replaced.