Why Does The Safety Valve On My Compressor Pump Make A "popping" Sound?

Why Does The Safety Valve On My Compressor Pump Make A "popping" Sound?
by

1 Answer

Answer :

This is most commonly an indication of bad valves. Depending on the model valves could be rebuilt or replaced.
by

Related questions

Recovery of waste heat from hot fluid to fluid is called: a) thermo compressor b) waste heat recovery boiler c) heat Pump d) economizer

Description : Recovery of waste heat from hot fluid to fluid is called: a) thermo compressor b) waste heat recovery boiler c) heat Pump d) economizer

Last Answer : heat Pump

What should be done to prevent a safety valve to stick to its seat ?

Description : What should be done to prevent a safety valve to stick to its seat ?

Last Answer : Safety valve should be blown off periodically so that no corrosion can take place on valve and valve seat.

Why Does The Safety Valve On My Tank Blow Off?

Description : Why Does The Safety Valve On My Tank Blow Off?

Last Answer : This is caused by a pressure switch improperly installed, set too high or malfunctioning. Safety valves do not normally fail on their own.

Why did my computer make a popping sound, smell like it was burning, and then die?”?

Description : Why did my computer make a popping sound, smell like it was burning, and then die?”?

Last Answer : answer:Does the machine still work? My first guess is that you may have fried the power supply, or possibly one of your cards (or something else). Sometimes it's just a part that's had enough, though you're ... the drives or the motherboard, you - or the guy at the shop - can swap out the bad bits.

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Description : In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Last Answer : Ans: d

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d

The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Description : The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Last Answer : Ans: a

Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Description : Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Last Answer : Ans: a

In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Description : In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Last Answer : Ans: D

Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Description : Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Last Answer : ANSWER : A

Which of the following units is not present in both the vapor compression refrigeration system and absorption refrigeration system? (A) Expansion valve (B) Condenser (C) Refrigerator (D) Compressor

Description : Which of the following units is not present in both the vapor compression refrigeration system and absorption refrigeration system? (A) Expansion valve (B) Condenser (C) Refrigerator (D) Compressor

Last Answer : (D) Compressor

Popping sound from my TV?

Description : Popping sound from my TV?

Last Answer : Oh my TV is now working because all along the crackling sound was due to the TV.

What is that popping sound from my water heater?

Description : What is that popping sound from my water heater?

Last Answer : When the hot steel body of the water heater comes in contact with the cool air, the temperature variation causes a movement in the atoms of the steel.That's making the popping sound but if your heater is ... you get a new one because if it's doing it continuously it means the body has worn out.

Why is there a “popping” sound when you crack your knuckles, and is it dangerous to crack them?

Description : Why is there a “popping” sound when you crack your knuckles, and is it dangerous to crack them?

Last Answer : A number of reasons have been given for the characteristic popping sound associated with someone cracking their knuckles. One reason is that when a joint is contracted, small ligaments or ... the knuckle bones. However, most researchers believe knuckle cracking does not cause serious joint damage.

The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Description : The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Last Answer : (B) Entrainment separator

A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump. (A) Sump (B) Volute (C) Vacuum (D) Submerged

Description : A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump. (A) Sump (B) Volute (C) Vacuum (D) Submerged

Last Answer : (C) Vacuum

Which of the following has the maximum compression ratio? (A) Blower (B) Compressor (C) Vacuum pump (D) Fan

Description : Which of the following has the maximum compression ratio? (A) Blower (B) Compressor (C) Vacuum pump (D) Fan

Last Answer : (C) Vacuum pump

Water that is fed back to the boiler by the pump is called? a. Absorber b. Absolute c. Compressor d. Condensate

Description : Water that is fed back to the boiler by the pump is called? a. Absorber b. Absolute c. Compressor d. Condensate

Last Answer : d. Condensate

The electric motor in hybrid car can also act as_____ • A generator • A Fuel pump • Cooling fan • Compressor

Description : The electric motor in hybrid car can also act as_____ • A generator • A Fuel pump • Cooling fan • Compressor

Last Answer : • A generator

The basic difference between compressor and pump is

Description : The basic difference between compressor and pump is

Last Answer : A pump is a machine that moves a fluid either liquid or gas from one place to another. A compressor is a machine that compresses a gas into a smaller volume.

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

Foot valve provided in the pump is a __________ valve. (A) Direction control (B) Back pressure (C) Relief (D) Pressure reduction

Description : Foot valve provided in the pump is a __________ valve. (A) Direction control (B) Back pressure (C) Relief (D) Pressure reduction

Last Answer : (B) Back pressure

Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Description : Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Last Answer : (A) Is a positive displacement pump

Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Description : Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Last Answer : (A) Open

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

The vent valve provided in a liquid handling centrifugal pump is (A) Generally a needle valve (B) Used to release any gases that might be vapour locking the pump (C) Helpful in easy removal of samples (D) All (A), (B) and (C)

Description : The vent valve provided in a liquid handling centrifugal pump is (A) Generally a needle valve (B) Used to release any gases that might be vapour locking the pump (C) Helpful in easy removal of samples (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A relief valve (A) Provides back pressure for a cylinder (B) Unloads a pump (C) Is a directional control valve (D) None of these

Description : A relief valve (A) Provides back pressure for a cylinder (B) Unloads a pump (C) Is a directional control valve (D) None of these

Last Answer : (C) Is a directional control valve

A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Description : A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Last Answer : (B) A cylinder and a plunger

Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Description : Purpose of relief valve in a reciprocating pump is to (A) Protect the pump against developing excessive pressure (B) Facilitate unidirectional flow of liquid (C) Reduce the discharge pressure (D) Control the rate of discharge

Last Answer : (A) Protect the pump against developing excessive pressure

Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed, the head developed is maximum which is known as shut-off head (C) At a particular speed the discharge at which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Description : Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed ... which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Last Answer : (D) All the above

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Which of the following is a boiler accessory i.e., not a boiler mounting? (A) Blow off cock (B) Feed check valve (C) Feed water pump (D) Stop valve

Description : Which of the following is a boiler accessory i.e., not a boiler mounting? (A) Blow off cock (B) Feed check valve (C) Feed water pump (D) Stop valve

Last Answer : (C) Feed water pump

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Description : When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Last Answer : d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Description : When does the engine High Pressure fuel shut off valve close? a. After a booster pump failure b. When the engine fuel switch is selected ‘ON’ during engine start c. When flight idle is selected d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

Last Answer : d. When the engine fuel switch is selected ‘OFF’ during engine shut-down

What sociological perspective would view sports as serving as a safety valve for both participants and spectators allowing them to shed tension and aggressive energy in a socially acceptable way?

Description : What sociological perspective would view sports as serving as a safety valve for both participants and spectators allowing them to shed tension and aggressive energy in a socially acceptable way?

Last Answer : Need answer

The moisture in a refrigerant is removed by (a) evaporator (b) safety relief valve (c) dehumidifier (d) driers

Description : The moisture in a refrigerant is removed by (a) evaporator (b) safety relief valve (c) dehumidifier (d) driers

Last Answer : Ans: d

. Name the safety device used to protect the boiler, when the water level falls below a minimum level. (A) Blow down valve (B) Blow off cock (C) Fusible plug (D) Safety valve

Description : . Name the safety device used to protect the boiler, when the water level falls below a minimum level. (A) Blow down valve (B) Blow off cock (C) Fusible plug (D) Safety valve

Last Answer : (C) Fusible plug

What is safety valve?

Description : What is safety valve?

Last Answer : Answer: Rapid opening (popping action) full flow valve for air and other gases.

A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Description : A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Last Answer : (D) All of these

How does the dirty safety trip valve trip the safety trip at normal speed?

Description : How does the dirty safety trip valve trip the safety trip at normal speed?

Last Answer : Dirt may find its way to the safety trip valve and get deposited around the spring end cap end. This will block the clearance between the safety trip valve and the spring end cap. As a result the steam pressure in the spring cap gets lowered allowing the valve to close.

A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Last Answer : b. 3.14 mm

How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Description : How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Last Answer : Work remains unaltered and volumetric efficiency decreases.

Why axial flow compressor is preferred for gas turbines for aeroplanes ?

Description : Why axial flow compressor is preferred for gas turbines for aeroplanes ?

Last Answer : Because it has low frontal area.

Why gas turbine power plant needs efficient compressor ?

Description : Why gas turbine power plant needs efficient compressor ?

Last Answer : Because a large portion of turbine work is eaten away by compressor and its inefficiency will affect net power output and cost of generation.