Give examples of : (i) Electrical transducer (ii) Mechanical Transducer

Give examples of : (i) Electrical transducer (ii) Mechanical Transducer
by

1 Answer

Answer :

(i) Electrical transducer

Voltage measurement

Temperature measurement

Strain measurement

(ii) Mechanical Transducer

Pressure measurement

Force measurement

Velocity measurement
by

Related questions

Define transducer. State factors which are considered while selecting transducer for a particular application.

Description : Define transducer. State factors which are considered while selecting transducer for a particular application.

Last Answer : Transducer - It converts one form of signal into another form. A transducer is a device that is used to convert a physical quantity into its corresponding electrical signal. ... compatibility : The transducer should maintain input and output characteristic for the selected environmental condition.

Write example of each type (i) Primary transducer (ii) Active transducer (iii) Electrical transducer (iv) Digital transducer

Description : Write example of each type (i) Primary transducer (ii) Active transducer (iii) Electrical transducer (iv) Digital transducer

Last Answer : (i) Active transducer:-Thermocouple, piezoelectric, photovoltaic cell (ii) Primary transducer:- Bourdon tube, bellows, (iii) Electrical transducer.:- LVDT,RVDT, Hall effect, strain gauge, ... , optical pyrometer, radiation pyrometer (iv) Digital transducer:- Linear Encoder, digital taco generator

Define transducer. Give two examples of transducer.

Description : Define transducer. Give two examples of transducer.

Last Answer : It is a device which convert any form of physical energy in to electrical energy. Two examples of transducer (1) Strain gauge (2) Thermistor (3) Thermocouple (4) LVDT

Define Analog Transducer and give examples of it

Description : Define Analog Transducer and give examples of it

Last Answer : Analog Transducer: An analog transducer is a device that converts the input signal into a continuous DC signal of voltage or current. Examples: * Strain gauge * L.V.D.T * Thermocouple * Thermistor

Define transducer. Give two examples.

Description : Define transducer. Give two examples.

Last Answer : Transducer - It converts one form of signal into another form. A transducer is a device that is used to convert a physical quantity into its corresponding electrical signal.  Classification - 1. Active transducer 2. Passive transducer 

Which of the listed devices is used to measure pressure and convert it to an electrical signal? A. Transducer B. Reducer C. Transformer D. Rectifier

Description : Which of the listed devices is used to measure pressure and convert it to an electrical signal? A. Transducer B. Reducer C. Transformer D. Rectifier

Last Answer : Answer: A

List any two specifications of electrical pressure transducer.

Description : List any two specifications of electrical pressure transducer.

Last Answer : Specifications of electrical pressure transducer: - 1. Root Sum Squares (RSS) 2. Non-Linearity 3. Hysteresis 4. Non-Repeatability 5. Long-Term Stability 6. Zero Offset 7. Span ... Size 10. associated circuit 11. sensitivity 12. self-generated or external power source 13. Miscellaneous

Give one application each of following transducer: (i) LVDT (ii) RVDT (iii) Capacitive (iv) Piezoelectric

Description : Give one application each of following transducer: (i) LVDT (ii) RVDT (iii) Capacitive (iv) Piezoelectric

Last Answer : i) LVDT ➢ LVDT used to measure force ➢ LVDT used to measure strain ➢ LVDT used to measure weight ➢ LVDT used to measure tension ➢ LVDT used to measure pressure ➢ The ... flow meters, non-destructive test (NDT) equipment's ➢ Piezoelectric materials are used in ultrasonic transducers.

State two examples of active transducer.

Description : State two examples of active transducer.

Last Answer : Examples of active transducer: 1. Thermocouple 2. photovoltaic cells (solar cells) 3. Piezoelectric crystals. 4. Thermoelectric 5. Magnetostrictive 6. Electrokinetic

State two examples of passive transducer.

Description : State two examples of passive transducer.

Last Answer : Examples of passive transducer: 1. LDR 2. Thermistor 3. Strain Gauge 4. Resistive transducers. 5. Inductive transducers. 6. Photoconductive 7. Capacitive transducers. 8. Magnetoresistive 9. Thermoresistive 10. Electroresistive 11. RTD

State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type.

Description : State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type. 

Last Answer : Need of multistage amplifier: The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, ... use more than one stage of amplification. Such an amplifier is called a MULTISTAGE AMPLIFIER .

Give the speciality of zener diode. State its 2-3 applications

Description : Give the speciality of zener diode. State its 2-3 applications

Last Answer : Speciality - This diode can keep breakdown voltage constant across it. It is used in reverse bias. Applications - Zener diodes voltage regulation as reference elements surge suppressors switching applications clipper circuits.

Define : (i) Sensor (ii) Transducer

Description : Define : (i) Sensor (ii) Transducer

Last Answer : (i) Sensor : A device which detects or measures a physical property and records, indicates, or otherwise responds to it. (ii) Transducer : a device that converts variations in a physical quantity, such as pressure or brightness, into an electrical signal, or vice versa.

Comparison of three configuration of BJT

Description : Comparison of three configuration of BJT

Last Answer : Parameter Common Base(CB) Common Emitter (CE) Common collector (CC) Input terminal  Emitter Base Base Common terminal Base Emitter Collector Output terminal Collector Collector Emitter Gain factor Alpha(Ic/Ie) Beta(Ic/Ib) Gamma(Ie/Ib)

Piezo-electric effect

Description : Piezo-electric effect

Last Answer : Piezoelectric Effect is the ability of certain materials to generate an electric charge in response to applied mechanical stress. The word Piezoelectric is derived from the Greek piezein, which means to squeeze or ... Storage Temperature Range: -55 to + 125°C Insulation Resistance: 500 M ohms

Shift Register

Description : Shift Register

Last Answer : Shift Register:- Shift Register is a group of flipflops used to shift data from one side to other side or to convert serial data into parallel or vice versa. Shift registers are of following types  i) ... iii) Parallel in serial out(PISO) iv) Parallel in parallel out(PIPO)

Comparison of BJT and FET

Description : Comparison of BJT and FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by both ... is comparatively more noisy. It is relatively immune to radiation. It is susceptible to radiation

Selection Criteria of PLC

Description : Selection Criteria of PLC

Last Answer : Selection criteria :- To select PLC for any particular application following points are to be considered. a) Type of PLC: Analog or Digital b) Number of inputs and outputs to PLC c) Operating voltage ... Type of memory of PLC g) Type of programming h) Reliability of PLC i) Flexibility of PLC

Function of OR Gate its logical symbol and truth table.

Description : Function of OR Gate its logical symbol and truth table.

Last Answer : Function: - OR gate is used to perform logical addition. So used in adder subtractor and logic circuits where logical Oring is required. Used to implement SOP form equations. Also used in PLA logic. Logical symbol of OR gate :- Truth table:- 

List various elements of mechatronic system and state applications.

Description : List various elements of mechatronic system and state applications.

Last Answer : Elements Sensors. Actuators (Hydraulics, Phnumetics) PLC, Micro controllers. Electrical Motors. Mechanical Couplings, Assembly & Gears. Control Panel. Applications ... washer and washing machines. automatic air conditioning systems unmanned aerial vehicles and automatic pilots. 

Define multiplexer. Draw logical symbol of 4:1 multiplexer with truth table and output logical equation

Description : Define multiplexer. Draw logical symbol of 4:1 multiplexer with truth table and output logical equation

Last Answer : Multiplexer - it is a combinational circuit which selects one input from several inputs and connects it to the output.  It is a circuit which has N-input and single output is called as multiplexer.

Compare microprocessor and microcontroller

Description : Compare microprocessor and microcontroller

Last Answer : Application Microprocessor - Computer, Mobile phone, calculator Microcontroller - washing machine, microwave oven Microprocessor Microcontroller Do not have inbuilt RAM or ROM ... access Less multifunction pins on the IC Many multifunction pins on the IC

Draw a labelled pin diagram of IC-555 and state function of each pin

Description : Draw a labelled pin diagram of IC-555 and state function of each pin

Last Answer : Pin Name Purpose 1 GND Ground reference voltage, low level (0 V)  2 TRIG The OUT pin goes high and a timing interval starts when this input falls below 1/2 of ... 8 Vcc Positive supply voltage, which is usually between 3 and 15 V depending on the variation.

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Compare LED and Photo diode

Description : Compare LED and Photo diode 

Last Answer : Parameters LED (Light Emitting Diode) Photodiode Definition Two terminal device which converts electrical energy into light energy.  Two Terminal Device which converts light energy into ... and Numeric display etc. Switching, high speed counting, ac coupled signaling etc.

Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Description : Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Last Answer : Rectifier filter is an electronic circuit that removes ripple or unwanted AC signal components from the output of a Rectifier. Types - (a) Series Inductor filter (d) Shunt capacitor filter (b) L-C type filter (e) Π - type filter

Draw simple block diagram of CNC machine and describe in short.

Description : Draw simple block diagram of CNC machine and describe in short.

Last Answer : (i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic tape ... Unit: A monitor is used to display the programs, commands and other useful data of CNC machine.

Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Description : Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Last Answer : Summing Amplifier Circuit In this simple summing amplifier circuit, the output voltage, ( Vout ) now becomes proportional to the sum of the input voltages, V1, V2, V3, etc. Then we can ... to the non-inverting input of the op-amp, it will produce the positive sum of the input voltages.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

List various types of CNC machine

Description : List various types of CNC machine

Last Answer : • CNC Plasma Cutting Machine. • CNC Laser Cutting Machine. • CNC Milling Machine. • CNC Router Machine. • CNC Lathe Machine.

State important specification parameters of ADC

Description : State important specification parameters of ADC

Last Answer : Accuracy Resolution Linearity Conversion time Settling time stability

Draw pin diagram of Op-Amp IC-741.

Description : Draw pin diagram of Op-Amp IC-741.

Last Answer : Pin diagram of Op-Amp IC-741 :

Define counter. State four applications of counter.

Description : Define counter. State four applications of counter.

Last Answer : Counter - The circuit which counts number of clock pulses is called as counter. Applications - Processor Real time clock Calculator Batch counter

Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Description : Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Last Answer : Configuration - Common Emitter Common Collector Common Base

Why NAND and NOR gate are called as universal gate? Draw AND gate using NAND gate only.

Description : Why NAND and NOR gate are called as universal gate? Draw AND gate using NAND gate only. 

Last Answer : Universal gate - All basic gates functionality can be implemented using NAND and NOR gate hence these gates are called as universal gates.  AND gate using NAND gate

Give classification of transducer on any two factors

Description : Give classification of transducer on any two factors

Last Answer : The transducers can be classified as: - 1. Active and passive transducers. 2. Analog and digital transducers. 3. On the basis of transduction principle used. 4. Primary and secondary transducer 5. Transducers and inverse transducers

The repeatability of NC machine depends on a.control loop errors b.mechanical errors c.electrical errors d.none of the mentioned

Description : The repeatability of NC machine depends on a.control loop errors b.mechanical errors c.electrical errors d.none of the mentioned

Last Answer : b.mechanical errors

By which device mechanical energy is converted into electrical energy? -General Knowledge

Description : By which device mechanical energy is converted into electrical energy? -General Knowledge

Last Answer : Dynamo The device used to convert mechanical energy into electrical energy is called Dynamo.

What is the name of the device that converts mechanical energy into electrical energy ?

Description : What is the name of the device that converts mechanical energy into electrical energy ?

Last Answer : Generator is a device that converts mechanical energy into electrical energy.

How are similarities between thermal energy and electrical energy mechanical energy electromagnetic?

Description : How are similarities between thermal energy and electrical energy mechanical energy electromagnetic?

Last Answer : They are both an energy

What is the machine that converts mechanical energy or motion into electrical energy?

Description : What is the machine that converts mechanical energy or motion into electrical energy?

Last Answer : generator

Is sanding a board chemical energy to mechanical or electrical energy?

Description : Is sanding a board chemical energy to mechanical or electrical energy?

Last Answer : Feel Free to Answer

What is a device that transforms mechanical energy to electrical energy?

Description : What is a device that transforms mechanical energy to electrical energy?

Last Answer : An electric generator.

What is the machine that converts mechanical energy or motion into electrical energy?

Description : What is the machine that converts mechanical energy or motion into electrical energy?

Last Answer : generator

Computers built before the First Generation of computers were: A) Mechanical B) Electro-mechanical C) Electrical D) None of these

Description : Computers built before the First Generation of computers were: A) Mechanical B) Electro-mechanical C) Electrical D) None of these

Last Answer : Answer : B

Which technology is used in Compact disks? A) Mechanical B) Electrical C) Electro Magnetic D) Laser

Description : Which technology is used in Compact disks? A) Mechanical B) Electrical C) Electro Magnetic D) Laser

Last Answer : Answer : D

In microphone, transformation of energy takes place from (a) Sound into electrical energy (b) Electrical into sound energy (c) Sound into mechanical energy (d) Mechanical into sound energy

Description : In microphone, transformation of energy takes place from (a) Sound into electrical energy (b) Electrical into sound energy (c) Sound into mechanical energy (d) Mechanical into sound energy

Last Answer : Ans:(b)

The device used for converting mechanical energy into electrical energy is called a/an (a) cell (b) transformer (c) dynamo (d) electric motor

Description : The device used for converting mechanical energy into electrical energy is called a/an (a) cell (b) transformer (c) dynamo (d) electric motor

Last Answer : Ans:(c)

Energy conversions taking place in a microphone are (a) sound to mechanical to electrical (b) electrical to mechanical to sound (c) sound to mechanical (d) mechanical to sound

Description : Energy conversions taking place in a microphone are (a) sound to mechanical to electrical (b) electrical to mechanical to sound (c) sound to mechanical (d) mechanical to sound

Last Answer : Ans:(a)

Which of the following devices converts electrical energy into mechanical energy? (a) Dynamo (b) Transformer (c) Electric motor (d) Inductor

Description : Which of the following devices converts electrical energy into mechanical energy? (a) Dynamo (b) Transformer (c) Electric motor (d) Inductor

Last Answer : Ans:(c)