Mention the important parts of a power transformer and their purposes.

Mention the important parts of a power transformer and their purposes. 
by

1 Answer

Answer :

Conservator: This allows for shrinkage and swelling of transformer oil. When the oil is heated up it swells and rises to the conservator. When cools down it goes back to main tank. Conservator reduces sludge formation of oil because only the oil surface in conservator is exposed to atmosphere where oil in the main tank is not exposed to atmosphere.

Breather: It provides dry sir to conservator when transformer breathes. That is when there is shrinkage of oil atmospheric air enters conservator through breather. The moisture is absorbed in breather by silica gel. 

Buchholz relay (gas operated): If there is an initial fault, heating up of core, high resistance joints heating up by conduction through insulation and supports. There is heating up of oil, which breaks down and gases are released. This gas actuates the mechanics in the relay, There by closing contacts of mercury switches for alarm. Also if there is a short circuit, the buchholz relay will trip the transformer. Also if there is any leakage of oil through bushing etc and oil level comes down the relay will give alarm and also will trip the transformer if transformer oil level comes down the point. Gases can be taken from the relay to identify nature of fault. 

Explosion vent: It provided on transformer main tank, provided with two Bakelite diaphragm which break when the pressure exceeds 5 psi in the transformer tank and relieve the pressure.

Core: To provide low reluctance path for the magnetic lines of force. It carries both the HV and LV windings.

HV Winding: High voltage is given to HV winding and low voltage is taken from the LV winding.

LV Winding: Low voltage is given to LV winding and high voltage is taken from the HV winding.

Cooling tubes: These are provided to cool the transformer oil so that the heat of oil will be given to the atmosphere.

HT bushing: Carries the HV terminals.

LT bushing: Carries the LV terminals. 

Tap changer: this is provided so that we can get the required voltage out put. There are two types of tap changer. Online tap changer and off line tap changer.  
by

Related questions

For what purposes transformer ratio meter can be used?

Description : For what purposes transformer ratio meter can be used? 

Last Answer : Transformer ratio meter can be used for, a. To find the ratio of a transformer. b. To find the phase angle deviation of primary and secondary voltage of transformer.  c. To find the magnitude of magnetizing currents. 

What are the purposes or advantages of transformer?

Description : What are the purposes or advantages of transformer?

Last Answer : Purposes a. Electrical energy may be transmitted economically over long distance by stepping up of voltages to reduce the line losses. b. To distribute the low voltages at consumer side by stepping down ... There by efficiency is high and about 95 to 98%. b. Practically maintenance is very less.

Mention the short comings of Merz Price scheme of protection applied to a power transformer.

Description : Mention the short comings of Merz Price scheme of protection applied to a power transformer.

Last Answer : In a power transformer, currents in the primary and secondary are to be compared. As these two currents are usually different, the use of identical transformers will give differential current, and ... turn-ratio are used, the differential current may flow through the relay under normal condition.

What are the losses in a power transformer and mention how these losses can be minimised?

Description : What are the losses in a power transformer and mention how these losses can be minimised?

Last Answer : There are two losses in a transformer. a. Iron losses. b. Copper losses. Iron losses - Iron losses constitutes of two losses. a. Eddy current losses, these are due to the induced emf in the core ... the load current I - current through winding. r - resistance of winding. t - time duration. 

What are the purposes of the transformer in a power supply?

Description : What are the purposes of the transformer in a power supply?

Last Answer : It couples the power supply to the ac line voltage, isolates the ac line voltage from the load, and steps this voltage up or down to the desired level.

Mention the properties of transformer oil.

Description : Mention the properties of transformer oil.

Last Answer : Properties of transformer oil are, a) Colour – pale yellow. b) Moisture content -

(a) Mention two reasons why Tropical Evergreen Forests are difficult to exploit for commercial purposes. -Geography

Description : (a) Mention two reasons why Tropical Evergreen Forests are difficult to exploit for commercial purposes. -Geography

Last Answer : (a) Tropical evergreen forests are difficult to exploit for commercial purposes because they are dense and found in mixed stands. (b) Two characteristics of tidal forests are : (i) They ... is used for house construction and furniture. Myrobalan: Its fruit provide material for tanning leather.

Mention two reasons why Tropical Evergreen Forests are difficult to exploit for commercial purposes. -SST 10th

Description : Mention two reasons why Tropical Evergreen Forests are difficult to exploit for commercial purposes. -SST 10th

Last Answer : Tropical evergreen forests do not occur in pure stands. The forests are dark and dense so difficult for commercial exploitation.

Write the most important mode of operation of power system and mention the major problems encountered with it.

Description : Write the most important mode of operation of power system and mention the major problems encountered with it.

Last Answer : Symmetrical steady state is the most important mode of operation of power system. Three major problems are encountered in this mode of operation. They are, 1) Load flow problem 2) Optimal load scheduling problem 3) Systems control problem

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. The starting current is held below the rated current. D. The field winding is energized for starting purposes only.

Description : Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. ... is held below the rated current. D. The field winding is energized for starting purposes only.

Last Answer : Answer: A

What are the purposes of cable trays?

Description : What are the purposes of cable trays? 

Last Answer : a. Avoid sagging of cables b. Give mechanical support 

What type of governing system used in turbine and what are the purposes of the system?

Description : What type of governing system used in turbine and what are the purposes of the system? 

Last Answer : Hydraulic governing system of centrifugal (speed) governer type is adopted in turbine. Sensitive oil pressure to actuate centrifugal governer is 6.1 kg/cm2 (max). At 6.7 kg/cm2 relief valve ... speeder gear from BPC signal. Once synchronised the grid frequency and speeder gear controls the speed. 

What are the purposes of barring gear?

Description : What are the purposes of barring gear?

Last Answer : Start rotor from rest. Eliminates sag in rotor - straighten and avoid rubbing at glands. Avoid direct contact journals and bearings. Avoid differential temp between top and bottom of cylinder due to convection of Steam or hot air inside turbine cylinders. 

What are the purposes of bleed condenser?

Description : What are the purposes of bleed condenser?

Last Answer : The purposes of bleed condenser are, a. To cool the bleed water, which goes to bleed cooler.  b. To provide cool hot water to the PHT purification system. 

What are the purposes of turning gear?

Description : What are the purposes of turning gear? 

Last Answer : Turning gear is used to run the turbine from rest to low speed and from normal running speed to low speed with the help of barring motor to eliminate the hogging and sagging of turbine because of the high temperature. 

What parameters or technical particulars are important to be considered while designing protection scheme of the transformer?

Description : What parameters or technical particulars are important to be considered while designing protection scheme of the transformer?

Last Answer : 1.Network Diagram showing the position of the transformer in the system 2.kVA or MVA rating of the transformer 3.Fault Level at the transformer 4.Voltage Ratio 5.Winding Connections 6.Per Unit ... Oil Filled 11.Length and area of cross section of the connecting leads between CTs and Relay Panel

Mention the important properties of relay contacts.

Description : Mention the important properties of relay contacts. 

Last Answer : a. Should be robust in construction. b. Self-cleaning (oxides easily breakdown). c. Corrosion resistant. d. Bounces free and striction free (low contact resistance). e. Able to carry rated continuous current and short time rated current. 

The harmonic currents in a power transformer does not cause increase in: a) Secondary voltage b) Core loss c) Copper loss d) Magnetic interference with protective relays

Description : The harmonic currents in a power transformer does not cause increase in: a) Secondary voltage b) Core loss c) Copper loss d) Magnetic interference with protective relays

Last Answer : Ans: A

A transformer has negative voltage regulation when its load power factor is- (a) Zero (b) Unity (c) Leading (d) Lagging

Description : A transformer has negative voltage regulation when its load power factor is- (a) Zero (b) Unity (c) Leading (d) Lagging

Last Answer : Ans: C

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Description : Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Last Answer : Answer: C

A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Description : A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Last Answer : Answer: C

A transformer works on the basic principle of ____________. A. self impedance B. attraction and repulsion C. mutual induction D. increasing power

Description : A transformer works on the basic principle of ____________. A. self impedance B. attraction and repulsion C. mutual induction D. increasing power

Last Answer : Answer: C

The function of a stepdown potential transformer is to reduce the load _____________. A. voltage and current B. voltage and increase line current C. current and increase line voltage D. power

Description : The function of a stepdown potential transformer is to reduce the load _____________. A. voltage and current B. voltage and increase line current C. current and increase line voltage D. power

Last Answer : Answer: B

How Generator Transformer is cooled in Thermal Power Plant?

Description : How Generator Transformer is cooled in Thermal Power Plant?

Last Answer : Answer: MVA power rating of the Generator Transformer will be equal to the alternator. Hence lot of heat will be generated while generator transformer is under operation. Oil Forced Air Forced (OFAF) type of cooling is employed for generator transformer

How Generator Transformer is cooled in Thermal Power Plant?

Description : How Generator Transformer is cooled in Thermal Power Plant?

Last Answer : MVA power rating of the Generator Transformer will be equal to the alternator. Hence lot of heat will be generated while generator transformer is under operation. Oil Forced Air Forced (OFAF) type of cooling is employed for generator transformer

At what power maximum efficiency of power transformer and distribution transformer is designed

Description : At what power maximum efficiency of power transformer and distribution transformer is designed

Last Answer : Maximum efficiency of the transformer is attained at certain load factor (α) when core losses of transformer is equal to the copper losses. PCore loss = α ^2 X PCopper loss From the ... the day. Hence distribution transformers are designed to have maximum efficiency at 50% of the rated full load

During No load why the power factor of the transformer is very low ?

Description : During No load why the power factor of the transformer is very low ?

Last Answer : Current flowing through the transformer consists of two components. Magnetizing current (Im) which is in quadrature (90 0 ) to the applied voltage and in phase current which is in phase to the applied voltage ... power factor of transformer during no load condition will by in the order of 0.1 to 0.2

During No load why the power factor of the transformer is very low ?

Description : During No load why the power factor of the transformer is very low ?

Last Answer : A. Current flowing through the transformer consists of two components. Magnetizing current (Im) which is in quadrature (900) to the applied voltage and in phase current which is in phase to the applied voltage ... factor of transformer during no load condition will by in the order of 0.1 to 0.2

What are power transformer?

Description : What are power transformer?

Last Answer : Power transformer is used for the transmission purpose at heavy load, high voltage greater than 33 KV & 100% efficiency. It is big in size as compared to distribution transformer, it used in generating station and Transmission substation. It is generally rated above 200MVA.

What are the problems arising in differential protection in power transformer and how are they overcome?

Description : What are the problems arising in differential protection in power transformer and how are they overcome?

Last Answer : 1. Difference in lengths of pilot wires on either sides of the relay. This is overcome by connecting adjustable resistors to pilot wires to get equipotential points on the pilot wires. 2. ... harmonic restraining unit is added to the relay which will block it when the transformer is energized.

Define the percentage voltage regulation and efficiency of a power transformer.

Description : Define the percentage voltage regulation and efficiency of a power transformer.  

Last Answer : Voltage regulation is the difference between no load voltage and full load voltage by no load voltage. Voltage regulation = No load voltage - Full load voltage / No load voltage. Voltage regulation is mentioned ... . % Efficiency = Output in watts * 100 / Output in watts + losses. 

A two-winding single phase transformer has a voltage regulation of 4.5% at full-load and unity power-factor. At full-load and 0.80 power-factor lagging load the voltage regulation will be (A) 4.5%. (B) less than 4.5%. (C) more than 4.5%. (D) 4.5% or more than 4.5%.

Description : A two-winding single phase transformer has a voltage regulation of 4.5% at full-load and unity power-factor. At full-load and 0.80 power-factor lagging load the voltage regulation will be (A) 4.5%. (B) less than 4.5%. (C) more than 4.5%. (D) 4.5% or more than 4.5%.

Last Answer : (C) more than 4.5%.

It is important to use the available land for various purposes with careful planning”. Give reason. -SST 10th

Description : It is important to use the available land for various purposes with careful planning”. Give reason. -SST 10th

Last Answer : Because land is an asset of a finite magnitude.

Is it really important to use an alkaline battery instead of a cheaper one for everyday purposes?

Description : Is it really important to use an alkaline battery instead of a cheaper one for everyday purposes?

Last Answer : Alkaline batteries work better and last much longer then the cheap ones that are marked heavy duty. You can purchase alkaline batteries for a reasonable price simply by avoiding brand names.

Which of the following statements is incorrect about materiality? a. The concept of materiality recognizes that some matters are important for fair presentation of financial statements in conformity with GAAP, while other matters are not important. b. An auditor considers materiality for planning purposes in terms of the largest aggregate level of misstatements that could be material to any one of the financial statements. c. Materiality judgments are made in light of surrounding circumstances and necessarily involve both quantitative and qualitative judgments. d. An auditor’s consideration of materiality is influenced by the auditor’s perception of the needs of a reasonable person who will rely on the financial statements

Description : Which of the following statements is incorrect about materiality? a. The concept of materiality recognizes that some matters are important for fair presentation of financial statements in conformity with ... s perception of the needs of a reasonable person who will rely on the financial statements

Last Answer : An auditor considers materiality for planning purposes in terms of the largest aggregate level of misstatements that could be material to any one of the financial statements

Mention the disadvantages of low power factor? How can it be improved?

Description : Mention the disadvantages of low power factor? How can it be improved?

Last Answer : Disadvantages of low power factor: Line losses are 1.57 times unity power factor. Larger generators and transformers are required. Low lagging power factor causes a large voltage drop, hence ... will have to carry more current at low power factor. This requires a large conductor size.

Mention the factors on which the magnitude of the e.m.f induced in the transformer depends.

Description : Mention the factors on which the magnitude of the e.m.f induced in the transformer depends.

Last Answer : 1) E.m.f in the primary coil 2) Number of turns in the primary coil 3) Number of turns in the secondary coil 4) The core material

(a) Draw a diagram to show the nutrition in Amoeba and label the parts used for this purpose. Mention any other purpose served by this part other than nutrition. (b) Name the glands associated with digestion of starch in human digestive tract and mention their role. (c) How is required pH maintained in the stomach and small intestine? -Biology

Description : (a) Draw a diagram to show the nutrition in Amoeba and label the parts used for this purpose. Mention any other purpose served by this part other than nutrition. (b) Name the glands associated ... mention their role. (c) How is required pH maintained in the stomach and small intestine? -Biology

Last Answer : Answer.(a) Pseudopodia serves the purpose of locomotion apart from nutrition. (b) The salivary gland is associated with digestion of starch in human digestive tract. It secretes saliva which contains ... juice from liver makes the food alkaline in small intestine for the pancreatic enzymes to act.

Which power tool do I need for household purposes?

Description : Which power tool do I need for household purposes?

Last Answer : Solar electricity is the most reliable source of generating electricity, there is no emission of greenhouse gas and this will protect our community

Steam produced in a boiler can be used for a variety of purposes including space heating, drying and _________________ a. Sterilization b. Humidification c. Power generation d. All of above

Description : Steam produced in a boiler can be used for a variety of purposes including space heating, drying and _________________ a. Sterilization b. Humidification c. Power generation d. All of above

Last Answer : d. All of above

Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Last Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

Briefly describe the principle and function of a camera. Mention its essential parts along with brief comparison with an eye.

Description : Briefly describe the principle and function of a camera. Mention its essential parts along with brief comparison with an eye.

Last Answer : The most important tool of photography is the camera itself. Basically, a camera is a lighttight box with a lens on one side and light-sensitive film on the other. Parts: 1.camera box 2. ... change distance between lens & film in camera and change focal length of lens using ciliary muscles in eye.

Mention the two parts of the autonomic nervous system.

Description : Mention the two parts of the autonomic nervous system.

Last Answer : The two parts of the autonomic nervous system are: a) Sympathetic system b) para sympathetic system

Mention the parts of a reflex arc.

Description : Mention the parts of a reflex arc.

Last Answer : The five distinct parts of a reflex arc are: a) A receptor to receive stimulus (sense organs) b) Sensory neurons to conduct the impulses from receptors to the spinal cord or the hind brain. c) ... pass the impulse to an effector. e) An effector to take necessary action in response to the stimulus.

Where are the adrenal glands located? Mention the parts of the adrenal gland.

Description : Where are the adrenal glands located? Mention the parts of the adrenal gland.

Last Answer : The adrenal glands are located on the upper part of each kidney. Each adrenal gland has two parts an outer cortex and inner medulla.

I would like to know if there is anyone else out there who evaporates their tap water of chlorine for drinking purposes?

Description : I would like to know if there is anyone else out there who evaporates their tap water of chlorine for drinking purposes?

Last Answer : answer:I've recently been looking into the effects of chlorinated tap water on vegetable plants. One interesting point I found was that the typically mentioned 24 hour period to evaporate the chlorine was a ... the air-at least not at my house. Maybe putting the container in the oven would help.

The assumption underlying an audit of financial statements is that they will be used by a. Different groups for different purposes. b. The general public in making investment decisions. c. The board of directors as basis of declaring cash dividends. d. The regulatory agencies to verify information that is relevant to their supervisory functions.

Description : The assumption underlying an audit of financial statements is that they will be used by a. Different groups for different purposes. b. The general public in making investment decisions. c ... dividends. d. The regulatory agencies to verify information that is relevant to their supervisory functions.

Last Answer : Different groups for different purposes.

Which statement correctly describes the relationship between philosophical ethics and ethos? (a) Individuals who obey the conventions, mores, and rules of their cultures are already acting ethically. No further philosophical reflection is required. (b) Philosophical ethics distinguishes what people do value from what they should value. (c) What people do value and should value are, for all practical purposes, the same? (d) Philosophical ethics is too abstract to be useful in everyday life situations. Following the mores and customs of one’s culture is a more dependable way to make moral decisions.

Description : Which statement correctly describes the relationship between philosophical ethics and ethos? (a) Individuals who obey the conventions, mores, and rules of their cultures are already acting ethically. No ... mores and customs of one's culture is a more dependable way to make moral decisions.

Last Answer : (b) Philosophical ethics distinguishes what people do value from what they should value. (c) What people do value and should value are, for all practical purposes, the same?