How special current limiting resistance is connected with the seal in contact?

How special current limiting resistance is connected with the seal in contact?
by

1 Answer

Answer :

Special current limiting resistance is connected in series with the seal in contact.  
by

Related questions

When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1', stop button, 'CR' and 'M' contacts, 'M' coil, 'OL contacts, the 'CR' coil in parallel, 'L2' C. 'L1', stop button, jog button, 'CR' contact, 'CR' relay, 'L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Last Answer : Answer: B

If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Description : If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Last Answer : Answer: D

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Description : A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Last Answer : Answer: B

A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Description : A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Last Answer : Answer: D

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

What is the purpose of special metallic embossing seal ? a. Stamping the voucher of final payment of GPF b. Stamping the any type of payment voucher c. None of these

Description : What is the purpose of special metallic embossing seal ? a. Stamping the voucher of final payment of GPF b. Stamping the any type of payment voucher c. None of these

Last Answer : a. Stamping the voucher of final payment of GPF

The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Description : The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Last Answer : Answer: C

Why seal-off bushings are used in IPBD?

Description : Why seal-off bushings are used in IPBD?  

Last Answer : To prevent interchange of air at different temperature and leakage of hydrogen or infiltration of dust into the bus duct. 

What is the necessity of Seal oil system?

Description : What is the necessity of Seal oil system?

Last Answer : The annular gap between stator and rotor of the generator are to be sealed to prevent hydrogen leak from the casing. Type of seal – ring type shaft seals Pressure of seal oil – 4 kg/cm2

How seal oil pressure is maintained?

Description : How seal oil pressure is maintained?

Last Answer : Differential pressure regulator maintains the seal oil pressure at 0.7 kg / cm2 higher than H2 pressure. 

What is function of seal oil system?

Description : What is function of seal oil system?

Last Answer : Seal oil prevents the leakage of hydrogen from the generator casing to the atmosphere, where it can form explosive mixture. Seal oil is at higher pressure than hydrogen.

When portable cords are connected to devices such as portable tools, you must eliminate direct tension on the joints or terminal screws. Coast Guard Regulations (46 CFR), allow this to be done by _____________. A. knotting the cords together at the plugs B. taping the plugs together C. installing a special fitting to eliminate plug separation D. all of the above

Description : When portable cords are connected to devices such as portable tools, you must eliminate direct tension on the joints or terminal screws. Coast Guard Regulations (46 CFR), allow this to be done by ... the plugs together C. installing a special fitting to eliminate plug separation D. all of the above

Last Answer : Answer: D

The speed of a series wound winch motor is controlled by ____________. A. varying the voltage applied to the motor B. the weight of the load on the cargo boom C. overcurrent protection devices in the motor D. a hydraulic speed-limiting governor

Description : The speed of a series wound winch motor is controlled by ____________. A. varying the voltage applied to the motor B. the weight of the load on the cargo boom C. overcurrent protection devices in the motor D. a hydraulic speed-limiting governor

Last Answer : Answer: A

Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components with a soft cotton rag. B. Blowing a high velocity stream of compressed air rapidly across the components. C. Using a vacuum cleaner to remove debris from the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.

Description : Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components ... the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.

Last Answer : Answer: C

Limiting moment of resistance of a singly reinforced section for mild steel is [ A ] Mu = 0.133 fck bd2 [ B ] Mu = 0.138 fck bd2 [ C ] Mu = 0.148 fck bd2 [ D ] Mu = 0.153 fck bd2

Description : Limiting moment of resistance of a singly reinforced section for mild steel is [ A ] Mu = 0.133 fck bd2 [ B ] Mu = 0.138 fck bd2 [ C ] Mu = 0.148 fck bd2 [ D ] Mu = 0.153 fck bd2

Last Answer : [ C ] Mu = 0.148 fck bd2

In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Description : In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Last Answer : Answer: A

In the illustration, the purpose of part B is to _________. EL-0033 A. increase resistance in series with the contacts as they close to prevent arcing B. create a magnetic field in the steel plates that interacts with the arc to cool and extinguish the arc C. cause the contacts to open in the event of an overload D. provide ventilation to the contact when the breaker is close to rated capacity

Description : In the illustration, the purpose of part B is to _________. EL-0033 A. increase resistance in series with the contacts as they close to prevent arcing B. create a magnetic field in the steel ... event of an overload D. provide ventilation to the contact when the breaker is close to rated capacity

Last Answer : Answer: B

A fuse will blow for all the listed reasons EXCEPT ________. A. excessive vibration B. extremely hot surroundings C. loose fuse clips D. low contact resistance within the fuse

Description : A fuse will blow for all the listed reasons EXCEPT ________. A. excessive vibration B. extremely hot surroundings C. loose fuse clips D. low contact resistance within the fuse

Last Answer : Answer: D

During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Description : During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Last Answer : Answer: B

If you disconnect and arrange both ends of a three conductor cable, without any contact between the individual conductors, an indicated ohmic value between the ends of a single conductor would indicate ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Description : If you disconnect and arrange both ends of a three conductor cable, without any contact between the individual conductors, an indicated ohmic value between the ends of a single conductor would indicate ... resistance C. the presence of a partial ground D. that the conductor is not short circuited

Last Answer : Answer: A

Grease coatings on electrical contact surfaces increase contact resistance and should be removed with a/an _______________. A. small wire brush B. compressed air jet C. clean dry cloth D. 10% solution carbon solvent and water

Description : Grease coatings on electrical contact surfaces increase contact resistance and should be removed with a/an _______________. A. small wire brush B. compressed air jet C. clean dry cloth D. 10% solution carbon solvent and water

Last Answer : Answer: C

Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove metallic dust. C. The contact surfaces should be greased to increase contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Description : Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove ... contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Last Answer : Answer: D

Different between megger and contact resistance meter?

Description : Different between megger and contact resistance meter?

Last Answer : Answers: Megger used to measure cable resistance, conductor continuity, phase identification where as contact resistance meter used to measure low resistance like relays ,contactors.

What is the difference between megger test equipment and contact resistance meter test instruments?

Description : What is the difference between megger test equipment and contact resistance meter test instruments?

Last Answer : Megger test equipment used to measure cable electric resistance, conductor continuity, phase identification. Contact resistance meter test instruments used to measure low resistance like relays, contactors.

How the contact resistance can increase?

Description : How the contact resistance can increase?  

Last Answer : Humidity + salty air, dust, poor contact pressure 

Different between megger and contact resistance meter?

Description : Different between megger and contact resistance meter?

Last Answer :  Megger used to measure cable resistance, conductor continuity, phase identification where as contact resistance meter used to measure low resistance like relays, contactors.

The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across 'R1', 'R2' and 'R3' will be different if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Last Answer : Answer: B

Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Description : Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Last Answer : Answer: A

If a circuit has resistances of 5, 10, and 20 ohms connected in parallel, what is the combined resistance of the circuit? A. 1.5 ohms B. 2.9 ohms C. 17.5 ohms D. 35.0 ohms

Description : If a circuit has resistances of 5, 10, and 20 ohms connected in parallel, what is the combined resistance of the circuit? A. 1.5 ohms B. 2.9 ohms C. 17.5 ohms D. 35.0 ohms

Last Answer : Answer: B

The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________. A. number of connected poles in the stator B. frequency to the motor C. excitation voltage D. resistance of the rotor circuit

Description : The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________. A. number of connected poles in the stator B. frequency to the motor C. excitation voltage D. resistance of the rotor circuit

Last Answer : Answer: A

When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Description : When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Last Answer : Answer: C

A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value B. deflect to zero and remain at that position C. swing to a high reading and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Description : A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value ... and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Last Answer : Answer: B

The speed of a squirrel-cage motor is usually changed by _____________. A. varying the frequency to the machine B. adding resistance in series with the stator windings C. adding resistance in parallel with the stator windings D. changing the number of connected poles in the stator

Description : The speed of a squirrel-cage motor is usually changed by _____________. A. varying the frequency to the machine B. adding resistance in series with the stator windings C. adding resistance in parallel with the stator windings D. changing the number of connected poles in the stator

Last Answer : Answer: D

To carry out an insulation resistance test, one terminal of the megohmmeter should be connected to the winding, with the other terminal being connected to the ____________________. A. power supply B. variable resistor C. frame of the machine D. armature

Description : To carry out an insulation resistance test, one terminal of the megohmmeter should be connected to the winding, with the other terminal being connected to the ____________________. A. power supply B. variable resistor C. frame of the machine D. armature

Last Answer : Answer: C

A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value for the capacitor B. first swing quickly to 'zero', then gradually move up the scale as the capacitor charges C. immediately deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Description : A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance ... deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Last Answer : Answer: C

An adjustable resistor, whose resistance can be changed without opening the circuit in which it is connected, is called a _____________. A. bleeder resistor B. rheostat C. bridge D. variable shunt strip

Description : An adjustable resistor, whose resistance can be changed without opening the circuit in which it is connected, is called a _____________. A. bleeder resistor B. rheostat C. bridge D. variable shunt strip

Last Answer : Answer: B

If you obtain a low resistance reading with a megohmmeter connected between terminals 'A' and 'C' of the three-phase, wye-connected winding shown in the illustration, there is __________. EL-0074 A. no open circuit between 'A' and 'C' B. no open circuit between 'C' and 'B' C. an open circuit between 'A' and 'C' D. an open circuit in both windings

Description : If you obtain a low resistance reading with a megohmmeter connected between terminals 'A' and 'C' of the three-phase, wye-connected winding shown in the illustration, there is __________. EL-0074 A. no open circuit ... 'B' C. an open circuit between 'A' and 'C' D. an open circuit in both windings

Last Answer : Answer: A

Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel C. the resistor banks are composed of individual series-connected units D. there are separate switches for the motor and the control

Description : Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel ... individual series-connected units D. there are separate switches for the motor and the control

Last Answer : Answer: B

A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the resistance B. both meters in parallel with the resistance C. the ammeter in series and the voltmeter in parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Description : A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the ... parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance

Last Answer : Answer: C

When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. adjusting the line voltage to calibrate the instrument C. plugging each end of one test lead into the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

How would you permanently kill and seal a volcano, using current science but with unlimited resources at your disposal?

Description : How would you permanently kill and seal a volcano, using current science but with unlimited resources at your disposal?

Last Answer : You could drop a mega mega ton hydrogen bomb down it’s throat but I don’t think it would be possible since you are dealing with a weak spot in the Earth’s crust. (You know, the old “Irresistible force meets immovable object” thing.)

What is a current limiting reactor ? How many types and what are they ?

Description : What is a current limiting reactor ? How many types and what are they ?

Last Answer : Answer : A current limiting reactor is basically an inductive coil which limits the short circuit current by providing inductive reactance when required. Types: 1. Based on the structure- a) Dry type ... reactor. Basbar reactors are again of 2 types- a) Ring system reactor b) Tiber system reactor

Which one is not the basic electrical protection measures in the Philippine Electronics Code? A. Voltage/ current limiting and interrupting B. Undergrounding C. Grounding and bonding D. Shielding

Description : Which one is not the basic electrical protection measures in the Philippine Electronics Code? A. Voltage/ current limiting and interrupting B. Undergrounding C. Grounding and bonding D. Shielding

Last Answer : B. Undergrounding

What is meant by current limiting?

Description : What is meant by current limiting?

Last Answer : Current limiting refers to the ability of a regulator to prevent the load current from increasing above a preset value.

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

What is the limiting factor as to the amount of current an electrodynamometer meter movement can handle?

Description : What is the limiting factor as to the amount of current an electrodynamometer meter movement can handle?

Last Answer : Size of spiral conducting.

What is the limiting factor as to the amount of current an electrodynamometer meter movement can handle?

Description : What is the limiting factor as to the amount of current an electrodynamometer meter movement can handle?

Last Answer : Size of spiral conducting.