Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components with a soft cotton rag. B. Blowing a high velocity stream of compressed air rapidly across the components. C. Using a vacuum cleaner to remove debris from the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.

Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components with a soft cotton rag. B. Blowing a high velocity stream of compressed air rapidly across the components. C. Using a vacuum cleaner to remove debris from the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.
by

1 Answer

Answer :

Answer: C
by

Related questions

To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings C. send it ashore to an approved service facility D. rinse all electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Description : To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings ... electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Last Answer : Answer: A

If a small electric motor has been submerged in saltwater for a short period of time, you should _____________. A. send it ashore for rewinding B. rinse it with warm freshwater and bake it dry in an oven C. soak it in a bucket of commercial solvent and bake with internal heat D. clean it with carbon tetrachloride and blow it out with compressed air

Description : If a small electric motor has been submerged in saltwater for a short period of time, you should _____________. A. send it ashore for rewinding B. rinse it with warm freshwater and bake it dry ... and bake with internal heat D. clean it with carbon tetrachloride and blow it out with compressed air

Last Answer : Answer: B

Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove metallic dust. C. The contact surfaces should be greased to increase contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Description : Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove ... contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Last Answer : Answer: D

Controller contacts should be routinely cleaned by ________. A. blowing with compressed air B. filing with a bastard file C. wiping with a clean dry cloth D. dressing with crocus cloth

Description : Controller contacts should be routinely cleaned by ________. A. blowing with compressed air B. filing with a bastard file C. wiping with a clean dry cloth D. dressing with crocus cloth

Last Answer : Answer: C

Which of the following procedures should be used to maintain a large electric motor during periods of inactivity? A. A thin layer of air-drying varnish should be applied on the windings. B. Compressed air should be blown over areas where dust is deposited. C. Spraying a solvent periodically to remove carbon dust. D. Space heaters should be used to prevent condensation of moisture.

Description : Which of the following procedures should be used to maintain a large electric motor during periods of inactivity? A. A thin layer of air-drying varnish should be applied on the windings. B. ... periodically to remove carbon dust. D. Space heaters should be used to prevent condensation of moisture.

Last Answer : Answer: D

Which of the following statements, concerning the general maintenance of a brushless generator, is correct? A. Paint should be applied to insulating surfaces on an annual basis. B. Alcohol should be used to remove dust and grime from windings. C. High pressure air should be used to blow out carbon dust. D. Accessible generator parts should be wiped with a clean dry rag on a periodic basis.

Description : Which of the following statements, concerning the general maintenance of a brushless generator, is correct? A. Paint should be applied to insulating surfaces on an annual basis. B. Alcohol should be used to ... . D. Accessible generator parts should be wiped with a clean dry rag on a periodic basis.

Last Answer : Answer: D

Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding temperature with an accurate mercury thermometer C. periodic cleaning of the winding insulation with an approved solvent D. making sure that the units are close to bulkheads or corners to protect them from damage

Description : Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding ... . making sure that the units are close to bulkheads or corners to protect them from damage

Last Answer : Answer: A

Compressed air should not be used to clean motor controller equipment because ________________. A. it may force metallic particles into coil insulation B. the surrounding area may need additional cleaning C. the air blast dries out insulation quickly D. a mask and respirator would be required

Description : Compressed air should not be used to clean motor controller equipment because ________________. A. it may force metallic particles into coil insulation B. the surrounding area may need additional cleaning C. the air blast dries out insulation quickly D. a mask and respirator would be required

Last Answer : Answer: A

Grease coatings on electrical contact surfaces increase contact resistance and should be removed with a/an _______________. A. small wire brush B. compressed air jet C. clean dry cloth D. 10% solution carbon solvent and water

Description : Grease coatings on electrical contact surfaces increase contact resistance and should be removed with a/an _______________. A. small wire brush B. compressed air jet C. clean dry cloth D. 10% solution carbon solvent and water

Last Answer : Answer: C

Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air? A. Open the machine on both ends so as to allow the air and dust to escape. B. Be certain that the circuit breaker is opened and tagged on the feeder panel. C. Be certain that the air is clean and as dry as possible. D. All of the above.

Description : Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air? A. Open the machine on both ends so as to allow the air and dust to escape. B. Be certain that the ... panel. C. Be certain that the air is clean and as dry as possible. D. All of the above.

Last Answer : Answer: D

With the DPI method of inspection after the contact time has elapsed the dye should be removed by: a) Spraying the surface with the remover till all dye has gone then wipe with clean cloth b) Spraying with the developer then wiping with a cloth c) Wipe clean, using a clean cloth soaked in a solvent remover d) it doesn’t matter how it is done as long as all traces of dye are removed

Description : With the DPI method of inspection after the contact time has elapsed the dye should be removed by: a) Spraying the surface with the remover till all dye has gone then wipe with clean cloth b) Spraying with ... remover d) it doesn't matter how it is done as long as all traces of dye are removed

Last Answer : c) Wipe clean, using a clean cloth soaked in a solvent remover

When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust and debris from the card and burnish the sliding connections C. make sure all connections are tight including wire wrappings and push-on types D. substitute a new or repaired spare card and check the operation of the circuit

Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit

Last Answer : Answer: D

For routine cleaning of a commutator, you should apply _____________. A. course sandpaper in a slow back and forth motion across the commutator slots B. an emery cloth parallel to the axis of the machine C. a canvas wiper to the machine while running D. cotton swabs between the commutator bars

Description : For routine cleaning of a commutator, you should apply _____________. A. course sandpaper in a slow back and forth motion across the commutator slots B. an emery cloth parallel to the axis of the machine C. a canvas wiper to the machine while running D. cotton swabs between the commutator bars

Last Answer : Answer: C

The commonly used solvent in supercritical extraction is (A) Methyl ethyl ketone (B) Water (C) Carbon tetrachloride (D) Carbon dioxide

Description : The commonly used solvent in supercritical extraction is (A) Methyl ethyl ketone (B) Water (C) Carbon tetrachloride (D) Carbon dioxide

Last Answer : (D) Carbon dioxide

. In which solvent are alkenes most soluble? (a) water (b) ethyl alcohol (c) ammonia (d) carbon tetrachloride

Description : . In which solvent are alkenes most soluble? (a) water (b) ethyl alcohol (c) ammonia (d) carbon tetrachloride

Last Answer : carbon tetrachloride

A pulsar is a rapidly spinning neutron star which emits: A. A blinding light when it aligns with the planets B. Radio waves detectable from Earth (Answer) C. A gravitational pull which attracts high energy dust particles D. Enough energy to power itself indefinitely

Description : A pulsar is a rapidly spinning neutron star which emits: A. A blinding light when it aligns with the planets B. Radio waves detectable from Earth (Answer) C. A gravitational pull which attracts high energy dust particles D. Enough energy to power itself indefinitely

Last Answer : B. Radio waves detectable from Earth (Answer)

Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: C

Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: D

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength of the insulation B. the paint dust is composed of abrasive and semi-conducting materials which impair insulation C. paint dust buildup has a tendency to cause corrosion D. phase windings frequently become isolated from each other due to dust interference at the terminals

Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals

Last Answer : Answer: B

Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Description : Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Last Answer : Answer: B

Consider the following chemicals: 1. Benzene 2. Carbon tetrachloride 3. Sodium carbonate 4. Trichloroethylene The chemicals used as dry cleaning agent(s) is/are (a) 1 only (b) 2 only (c) 1, 2 and 4 only (d) 1, 2, 3 and 4

Description : Consider the following chemicals: 1. Benzene 2. Carbon tetrachloride 3. Sodium carbonate 4. Trichloroethylene The chemicals used as dry cleaning agent(s) is/are (a) 1 only (b) 2 only (c) 1, 2 and 4 only (d) 1, 2, 3 and 4

Last Answer : Ans:(c)

A horizontal stream of charged particles is accelerated to velocity `3 xx10^(7) m s^(-1)` immediately before being allowed into an electric field betw

Description : A horizontal stream of charged particles is accelerated to velocity `3 xx10^(7) m s^(-1)` immediately before being allowed into an electric field betw

Last Answer : A horizontal stream of charged particles is accelerated to velocity `3 xx10^(7) m s^(-1)` ... field between plates = rate of change of potential]

Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Description : Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Last Answer : Answer: C

Doesn't a robotic vacuum cleaner damage furniture?

Description : I have new cabinets, then there will be no need for a robotic vacuum cleaner?

Last Answer : I have a robotic vacuum cleaner Vileda and I am satisfied. The furniture will definitely not damage the vacuum cleaner. If it hits an obstacle while vacuuming, tapping is not strong. The vacuum cleaner rotates by itself and continues to vacuum.

Wiping dust after luxation or vice versa?

Description : Wipe dust only after luxation or vice versa?

Last Answer : After luxation. This would have the greatest effect before and after luxation.

Which statement BEST describes plaque: A. It is a soft film composed mainly of food debris and can not be rinsed off teeth B. It is a soft film composed mainly of food debris and can be rinsed off teeth C. It is a soft film composed mainly of none calcified bacteria and can not be rinsed off the teeth D. It is a soft film composed mainly of dextran and can not be rinsed off the teeth E. It is a soft film composed mainly of dextran and can be rinsed off teeth.

Description : Which statement BEST describes plaque: A. It is a soft film composed mainly of food debris and can not be rinsed off teeth B. It is a soft film composed mainly of food debris and can be rinsed off ... rinsed off the teeth E. It is a soft film composed mainly of dextran and can be rinsed off teeth.

Last Answer : C. It is a soft film composed mainly of none calcified bacteria and can not be rinsed off the teeth

A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then for the same flow rate of water the new manometer reading will be __________ cms. (A) 17 (B) 42(C) 84 (D) 1.8

Description : A mercury (specific gravity = 13.6) manometer connected across an orificemeter fitted in a pipe shows a manometer reading of 2 cms. If the manometer liquid is changed to carbon tetrachloride (specific gravity = 1.6), then ... new manometer reading will be __________ cms. (A) 17 (B) 42 (C) 84 (D) 1.8

Last Answer : __________ cms. (A) 17

Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature (C) Electrostatic precipitator is the most efficient dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature

Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Description : Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Last Answer : Answer: C

Which of the listed procedures should be carried out to prevent moisture damage to electrical apparatus during extended periods of idleness? A. Fill the motor housing with CO2 to inert the space. B. Strap silica gel around the commutator. C. Place heat lamps in the motor housings. D. Cover the equipment with a canvas tarpaulin.

Description : Which of the listed procedures should be carried out to prevent moisture damage to electrical apparatus during extended periods of idleness? A. Fill the motor housing with CO2 to inert the space. B. Strap ... C. Place heat lamps in the motor housings. D. Cover the equipment with a canvas tarpaulin.

Last Answer : Answer: C

The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Description : The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Last Answer : Answer: A

How to Clean a Vacuum Cleaner?

Description : How to Clean a Vacuum Cleaner?

Last Answer : Vacuum cleaners come in all shapes and sizes and a variety ofprices. One thing they all have in common, however, is that just alittle maintenance goes a long way to avoiding expensive repairs. ... replaced with afresh one. Neglecting to change the bag can lead to decreasedsuction and damage to t

How to Clean a Vacuum Cleaner Bag

Description : How to Clean a Vacuum Cleaner Bag

Last Answer : How to Clean a Vacuum Cleaner Bag A vacuum cleaner does not require a lot of maintenance, but it is advisable to keep making small adjustments to ensure that it's running to its full potential. ... any kinks in it. This will cause problems, even if you have followed all other instructions correctly.

Maintenance and Care: How to clean your Vacuum Cleaner

Description : Maintenance and Care: How to clean your Vacuum Cleaner

Last Answer : Maintenance and Care: How to clean your Vacuum Cleaner There are numerous ways to clean your vacuum cleaner, depending on the brand (manufacturer) and design. However, it is best to ... will bother your work area. Remember, safety considerations are important to prevent any unwanted accidents.

The most efficient equipment for the removal of sub-micronic dust particles from blast furnace gas is the (A) Venturi atomiser (B) Gravity settling chamber (C) Electro-static precipitator (D) Cyclone separator

Description : The most efficient equipment for the removal of sub-micronic dust particles from blast furnace gas is the (A) Venturi atomiser (B) Gravity settling chamber (C) Electro-static precipitator (D) Cyclone separator

Last Answer : (C) Electro-static precipitator

Which is the most efficient dust removal equipment for removal of submicronic dust particles from blast furnace gas? (A) Packed scrubber (B) Gravity settling chamber (C) Electrostatic precipitator (D) Hydrocyclone

Description : Which is the most efficient dust removal equipment for removal of submicronic dust particles from blast furnace gas? (A) Packed scrubber (B) Gravity settling chamber (C) Electrostatic precipitator (D) Hydrocyclone

Last Answer : (C) Electrostatic precipitator

Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Last Answer : Answer: D

The sun appears red at sunrise and sunset while it appears white at noon because of _____ A. Refraction B. It is cooler at sunrise and at sunset C. Diffraction leading to red end of the spectrum reaching the earth D. Scattering of light due to dust particles and air molecules

Description : The sun appears red at sunrise and sunset while it appears white at noon because of _____ A. Refraction B. It is cooler at sunrise and at sunset C. Diffraction leading to red end of the spectrum reaching the earth D. Scattering of light due to dust particles and air molecules

Last Answer : ANSWER: D

The sun appears red at sunrise and sunset while it appears white at noon, because A. Of refraction B. It is cooler at sunrise and at sunset C. Of diffraction leading to red end of the spectrum reaching the earth. D. Of Scattering of light due to dust particles and air molecules?

Description : The sun appears red at sunrise and sunset while it appears white at noon, because A. Of refraction B. It is cooler at sunrise and at sunset C. Of diffraction leading to red end of the spectrum reaching the earth. D. Of Scattering of light due to dust particles and air molecules?

Last Answer : C. Of diffraction leading to red end of the spectrum reaching the earth.

Take a 250 mL beaker/glass tumbler. Fill half of it with water. Now carefully cut a small piece of sodium metal. Dry it using filter paper and wrap it in a small piece of cotton. Put the sodium piece wrapped in cotton into the beaker. Observe carefully. -Science

Description : Take a 250 mL beaker/glass tumbler. Fill half of it with water. Now carefully cut a small piece of sodium metal. Dry it using filter paper and wrap it in a small piece of cotton. Put the sodium piece wrapped in cotton into the beaker. Observe carefully. -Science

Last Answer : On touching the beaker, it was felt hot. The solution turns the red litmus paper to blue which shows it is basic in nature. Blue litmus paper do not show any colour change with the solution.

The advantage of using dental floss over rubber point interdentally: A. Remove plaque and debris in interproximal surfaces B. Polish C. Massage of the interdental papillae D. Aid and recognise subgingivally

Description : The advantage of using dental floss over rubber point interdentally: A. Remove plaque and debris in interproximal surfaces B. Polish C. Massage of the interdental papillae D. Aid and recognise subgingivally

Last Answer : A. Remove plaque and debris in interproximal surfaces

Can I clean my laptop screen with windex and a rag/paper towel?

Description : Can I clean my laptop screen with windex and a rag/paper towel?

Last Answer : If it has alcohol or ammonia in it, you shouldn't use it. I've also heard paper towels can scratch the screen, but who knows if that's true? I use a glasses cleaning cloth, which I lick, then ... want to do that, then use a microfiber cloth and water. If the water leaves streaks, use bottled water.

Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Description : Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Last Answer : Answer: C

Pick out the correct statement. (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of non￾ideal binary system by distillation (B) A sharp decrease in pressure drop is an indication of flooding in a distillation coloumn (C) Solvent used in extractive distillation should be of high volatility (D) Flash distillation is suitable for separating components which have very close boiling temperature

Description : Pick out the correct statement. (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of ... Flash distillation is suitable for separating components which have very close boiling temperature

Last Answer : (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of non￾ideal binary system by distillation

When using a spray can of compressed air/gas to clean your PC is it harmful to your computer when it comes out liquid when spraying?

Description : When using a spray can of compressed air/gas to clean your PC is it harmful to your computer when it comes out liquid when spraying?

Last Answer : answer:Not really, Just don't hold the can upside down or sideways if you can help it. There is a chance that it can discolor some plastics but otherwise don't worry about it. Duster is ... that is very unlikely. During gaming spec competitions they use liquid nitrogen as a CPU and GPU heatsink.

An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. The maximum allowable operating temperature of the machine. B. The temperature of the machine at the time the resistance reading was taken. C. The normal temperature rise of the machine. D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Description : An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. ... D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Last Answer : Answer: B