How seal oil pressure is maintained?

How seal oil pressure is maintained?
by

1 Answer

Answer :

Differential pressure regulator maintains the seal oil pressure at 0.7 kg / cm2 higher than H2 pressure. 
by

Related questions

Why water pressure is kept below the oil pressure? How it is maintained?

Description : Why water pressure is kept below the oil pressure? How it is maintained? 

Last Answer : Incase of a heat exchanger tube failure the water should not go inside the transformer. For this purpose the oil pressure is kept above the water pressure. 

What is the necessity of Seal oil system?

Description : What is the necessity of Seal oil system?

Last Answer : The annular gap between stator and rotor of the generator are to be sealed to prevent hydrogen leak from the casing. Type of seal – ring type shaft seals Pressure of seal oil – 4 kg/cm2

What is function of seal oil system?

Description : What is function of seal oil system?

Last Answer : Seal oil prevents the leakage of hydrogen from the generator casing to the atmosphere, where it can form explosive mixture. Seal oil is at higher pressure than hydrogen.

How lub oil supply is maintained?

Description : How lub oil supply is maintained?  

Last Answer : Lubrication oil is supply is maintained by outlet oil from turbine oil pumps during normal operation and jacking oil pump during startup.

What is the value of vacuum maintained by vacuum pump in oil filteration machine?

Description : What is the value of vacuum maintained by vacuum pump in oil filteration machine?

Last Answer : 27 Hg.

How dearator pressure is maintained after turbine trip?

Description : How dearator pressure is maintained after turbine trip? 

Last Answer : Pegging steam is used to maintain dearator pressure after turbine trip.  

How dearator pressure is maintained?

Description : How dearator pressure is maintained?  

Last Answer : Dearator pressure is normally maintained by extraction steam.  

Pressure maintained in the high pressure primary tower of a three stage crude oil distillation system is about __________ kg/cm2 . (A) 1.5 (B) 3 (C) 6 (D) 12

Description : Pressure maintained in the high pressure primary tower of a three stage crude oil distillation system is about __________ kg/cm2 . (A) 1.5 (B) 3 (C) 6 (D) 12

Last Answer : (B) 3

The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Last Answer : (B) 1 and 200

In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Description : In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Last Answer : (B) The oil film is maintained by supplying oil under pressure

Why seal-off bushings are used in IPBD?

Description : Why seal-off bushings are used in IPBD?  

Last Answer : To prevent interchange of air at different temperature and leakage of hydrogen or infiltration of dust into the bus duct. 

How special current limiting resistance is connected with the seal in contact?

Description : How special current limiting resistance is connected with the seal in contact?

Last Answer : Special current limiting resistance is connected in series with the seal in contact.  

What are the types of seal oil system?

Description : What are the types of seal oil system?

Last Answer : Answer: Gravity and pressurized.

Under normal conditions, storage batteries used for starting the emergency diesel generator are maintained in a charged state by which of the following methods? A. Trickle charging B. Fast charging C. Equalizing charge D. Reverse charging

Description : Under normal conditions, storage batteries used for starting the emergency diesel generator are maintained in a charged state by which of the following methods? A. Trickle charging B. Fast charging C. Equalizing charge D. Reverse charging

Last Answer : Answer: A

Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Description : Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Last Answer : Answer: A

You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, becoming fairly steady as the leakage current stabilizes B. remain constant as the temperature of the windings increases C. continue to drop as the potential is maintained, becoming fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Description : You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, ... fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Last Answer : Answer: A

A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Description : A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Last Answer : Answer: C

How coolant flow is maintained in the event of loss of power to the PHT system?

Description : How coolant flow is maintained in the event of loss of power to the PHT system?

Last Answer : When the PHT power fails, it takes two minutes for DG to come to full power. The circulation is maintained by flywheel, which increases the de-acceleration and maintains the flow for two minutes. If ... which more denser cold water comes down and less denser hot water goes up by convection method. 

Vacuum maintained in the vacuum distillation column in oil refinery is in the range of about __________ mm Hg absolute. (A) 1 to 5 (B) 30 to 80

Description : Vacuum maintained in the vacuum distillation column in oil refinery is in the range of about __________ mm Hg absolute. (A) 1 to 5 (B) 30 to 80

Last Answer : (B) 30 to 80

How powerful is a pressure seal on a mason jar?

Description : How powerful is a pressure seal on a mason jar?

Last Answer : THe seal on a mason jar is totally airtight. This seal keeps foods preserved inside the jars.

I am looking for a rubber seal for the lid to my old presto pressure cooker. Is there anyplace locally I can get one?

Description : I am looking for a rubber seal for the lid to my old presto pressure cooker. Is there anyplace locally I can get one?

Last Answer : Yes there is. Go to http://www.pressurecooker-canner.com/presto-pressure-cooker-parts.html and order the part you need and then it will be sent right to your door, they spealize in pressure cooker parts.

For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should be used (c) perfectly tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Last Answer : Ans: c

What pressure and composition of atmosphere within a space ship is maintained during space travel?

Description : What pressure and composition of atmosphere within a space ship is maintained during space travel?

Last Answer : Here’s one part of an answer to your multi-part question: the ENose.

Osmotic pressure is maintained by blood colloid

Description : Osmotic pressure is maintained by blood colloid

Last Answer : Osmotic pressure is maintained by blood colloid A. Albumin B. Globulin C. Fibrinogen D. Thrombin

Blood colloidal osmotic pressure mainly maintained by which plasma protein `:-`

Description : Blood colloidal osmotic pressure mainly maintained by which plasma protein `:-`

Last Answer : Blood colloidal osmotic pressure mainly maintained by which plasma protein `:-` A. Globulin B. Albumin C. Fibrinogen D. Prothombin

High blood pressure is maintained in glomeruli than in other capillaries because

Description : High blood pressure is maintained in glomeruli than in other capillaries because

Last Answer : High blood pressure is maintained in glomeruli than in other capillaries because A. The variability ... diameter than glomerulus D. All the above

A 45-year-old solicitor had an onset of severe, crushing, substernal chest pain while attending a football match. He collapsed on his way to the car. Bystander Cardiorespiratory Resuscitation was begun immediately and continued until arrival in Casualty where an endotracheal tube was inserted and ventilation was maintained on 100% oxygen. Investigations revealed: pH 7.13 PaO2 560 mmHg PaCO2 18 mmHg Bicarbonate 5.8 SaO2 98% Based on these laboratory values, which of the following statements best describes his current pathophysiology? 1) He is demonstrating a primary respiratory alkalosis 2) He probably developed a large right to left intracardiac shunt 3) His anion gap is probably normal 4) His oxyhemoglobin curve is shifted to the left 5) His pulmonary artery pressure is probably elevated

Description : A 45-year-old solicitor had an onset of severe, crushing, substernal chest pain while attending a football match. He collapsed on his way to the car. Bystander Cardiorespiratory Resuscitation ... His oxyhemoglobin curve is shifted to the left 5) His pulmonary artery pressure is probably elevated

Last Answer : Answers-5 This young patient with severe central chest pain has probably arrested due to myocardial infarction and arrhythmia. His gases reveal high PO2 following 100% O2 but severe acidosis ... no left to right shunting and high pulmonary pressures would be expected after this arrest scenario.

Inside an aeroplane flying at a high altitude, (a) the pressure is the same as that outside (b) normal atmospheric pressure is maintained by the use of air pumps (c) the pressure inside is less than the pressure outside (d) normal humidity and partial vacuum are maintained

Description : Inside an aeroplane flying at a high altitude, (a) the pressure is the same as that outside (b) normal atmospheric pressure is maintained by the use of air pumps (c) the pressure inside is less than the pressure outside (d) normal humidity and partial vacuum are maintained

Last Answer : Ans:(b)

Of the four locations mentioned below, the highest inside temperature will be attained in the pressure cooker operated with the pressure valve open (a) At sea level (b) At the top of Mt Everest (c) At a place in a valley below sea level (d) In an aeroplane flying at a height of 10,000 m with inside pressure maintained at the sea level

Description : Of the four locations mentioned below, the highest inside temperature will be attained in the pressure cooker operated with the pressure valve open (a) At sea level (b) At the top of Mt Everest (c) ... ) In an aeroplane flying at a height of 10,000 m with inside pressure maintained at the sea level

Last Answer : Ans:(c)

Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm

Description : Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm

Last Answer : (A) 5°C and 1 kgf/cm

Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Description : Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Last Answer : (A) 50°C and 3 - 4 kg/cm

Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of light distillates (B) Suppress coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Last Answer : (B) Suppress coke formation

Pressure & temperature maintained in catalytic cracking is about (A) 2 atm & 500°C (B) 10 atm & 500°C (C) 30 atm & 200°C (D) 50 atm & 750°C

Description : Pressure & temperature maintained in catalytic cracking is about (A) 2 atm & 500°C (B) 10 atm & 500°C (C) 30 atm & 200°C (D) 50 atm & 750°C

Last Answer : (A) 2 atm & 500°C

Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward feeding in multiple effect evaporation (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Description : Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward ... (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Last Answer : (A) Get economical temperature difference by using moderate pressure steam

Pick out the wrong statement. (A) In a batch reactor, which is exclusively used for liquid phase reactions; temperature pressure and composition may vary with time (B) In a semi-batch reactor, one reactant is charged batch wise, while the other reactant is fed continuously (C) In a continuous flow reactor, uniform concentration cannot be maintained throughout the vessel even in a well agitated system (D) In a continuous flow reactor, both the reactants and the products flow out continuously

Description : Pick out the wrong statement. (A) In a batch reactor, which is exclusively used for liquid phase reactions; temperature pressure and composition may vary with time (B) In a semi-batch reactor, ... system (D) In a continuous flow reactor, both the reactants and the products flow out continuously

Last Answer : (C) In a continuous flow reactor, uniform concentration cannot be maintained throughout the vessel even in a well agitated system

Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration. b) 10-15 mm Hg water pressure. A measure of 10–15 mm Hg water pressure would indicate that the cuff is underinflated. c) 30-35 mm Hg water pressure. A measure of 30–35 mm Hg water pressure would indicate that the cuff is overinflated. d) 0-5 mm Hg water pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Description : Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the ... pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Last Answer : a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration.

An ideal gas is maintained at constant temperature. If the pressure on the gas is doubled, the volume is  a. increased fourfold  b. doubled  c. reduced by half  d. decreased by a quarter

Description : An ideal gas is maintained at constant temperature. If the pressure on the gas is doubled, the volume is  a. increased fourfold  b. doubled  c. reduced by half  d. decreased by a quarter

Last Answer : reduced by half

Coast Guard Regulations (46 CFR) require that the emergency diesel generator engine shut down when _____________. A. lubricating oil pressure is lost B. the engine overspeeds dangerously C. fixed CO2 is released into the emergency diesel generator space D. all of the above

Description : Coast Guard Regulations (46 CFR) require that the emergency diesel generator engine shut down when _____________. A. lubricating oil pressure is lost B. the engine overspeeds dangerously C. fixed CO2 is released into the emergency diesel generator space D. all of the above

Last Answer : Answer: D

Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions properly and trips generator #1 electrically off the bo A. Start the emergency generator. B. Ascertain cause of the low lube oil pressure. C. Strip the board of all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Description : Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions ... all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Last Answer : Answer: C

An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 volts were applied to the 'setpoint module' B. 'reduction gear lube oil pressure' fell below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Description : An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 ... below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Last Answer : Answer: B

What is the advantage of Pressure relief device in TELK type GT over explosion vent of BHEL, even though in both cases oil will be expelled out during sudden pressure rise?

Description : What is the advantage of Pressure relief device in TELK type GT over explosion vent of BHEL, even though in both cases oil will be expelled out during sudden pressure rise?

Last Answer : During internal fault, the internal pressure rise is relieved by the expelling out of oil through Pressure relief device /explosion vent. However the Pressure relief device closes back when the pressure ... hazard due to transformer oil does not exist after the closure of Pressure relief device. 

How would you permanently kill and seal a volcano, using current science but with unlimited resources at your disposal?

Description : How would you permanently kill and seal a volcano, using current science but with unlimited resources at your disposal?

Last Answer : You could drop a mega mega ton hydrogen bomb down it’s throat but I don’t think it would be possible since you are dealing with a weak spot in the Earth’s crust. (You know, the old “Irresistible force meets immovable object” thing.)

When was the last time you blew a seal?

Description : When was the last time you blew a seal?

Last Answer : Wat?

Why do you think the lady in this video never pet the seal?

Description : Why do you think the lady in this video never pet the seal?

Last Answer : Sealaphobia maybe?

Rough siding raw wood, seal first or prime?

Description : Rough siding raw wood, seal first or prime?

Last Answer : What kind of wood is it? That would make a differnce to me. I might want to see the grain so a sealer would be better. But if you don’t care about seeing it primer and then paint it.