What is the effect of salt content in moisture on resistivity?

What is the effect of salt content in moisture on resistivity?
by

1 Answer

Answer :

The resistivity decreases and the salt content is expressed in percent by weight of the contained moisture. It will be noted that the curve flattens off at about 5% salt content and a further increase in salt content gives little decrease in the soil resistivity. 
by

Related questions

What is the effect of moisture content on earth resistivity?

Description : What is the effect of moisture content on earth resistivity?

Last Answer : The moisture content is expressed in percent by weight of dry soil. Dry earth weights about 1440 kg per cubic meter and thus 10% moisture content is equivalent to 144 kg of water per cubic ... is very little affected. Below 20%, the resistivity increases very abruptly with the decrease in moisture.

Which of the listed conditions describes the effect on intrinsic semiconductor operation as a result of a temperature increase? A. Additional heat sinks will be required B. Conductivity will increase C. Conductivity will decrease D. Resistivity will increase

Description : Which of the listed conditions describes the effect on intrinsic semiconductor operation as a result of a temperature increase? A. Additional heat sinks will be required B. Conductivity will increase C. Conductivity will decrease D. Resistivity will increase

Last Answer : Answer: B

What is the effect of temperature on earth resistivity?

Description : What is the effect of temperature on earth resistivity?

Last Answer : The temperature co-efficient of resistivity for soil is negative, but it is negligible for temperature above freezing point. Below 0°C the water in the soil begins to freeze and introduces ... the temperature co-efficient, so that as the temperature becomes lower the resistivity rises enormously.  

Which of the following combination of processing and preservation techniques works best for smoked products? A. Salt and acidification B. Heat, salt, dipping in brine/ minimal moisture content C. Heat, salt, acidification/minimal moisture content D. Heat and solid content

Description : Which of the following combination of processing and preservation techniques works best for smoked products? A. Salt and acidification B. Heat, salt, dipping in brine/ minimal moisture content C. Heat, salt, acidification/minimal moisture content D. Heat and solid content

Last Answer : B. Heat, salt, dipping in brine/ minimal moisture content

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

What is the normal value of moisture content allowed in transformer oil?

Description : What is the normal value of moisture content allowed in transformer oil? 

Last Answer :

Coke used for the production of calcium carbide should have (A) Low ash content (B) Low ignition temperature (C) High electrical resistivity (D) All (A), (B) and (C)

Description : Coke used for the production of calcium carbide should have (A) Low ash content (B) Low ignition temperature (C) High electrical resistivity (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

By increasing impurity content in the metal alloy the residual resistivity always

Description : By increasing impurity content in the metal alloy the residual resistivity always

Last Answer : By increasing impurity content in the metal alloy the residual resistivity always increases.

The greatest detrimental effect on idle electrical equipment, such as cargo pump motors, is the _____________. A. loss of residual magnetism B. absorption of moisture in the insulation C. insulation varnish flaking D. dirt collecting on the windings

Description : The greatest detrimental effect on idle electrical equipment, such as cargo pump motors, is the _____________. A. loss of residual magnetism B. absorption of moisture in the insulation C. insulation varnish flaking D. dirt collecting on the windings

Last Answer : Answer: B

What should be the frequency of measurement of earth resistivity?

Description : What should be the frequency of measurement of earth resistivity?

Last Answer : As per IS: 3043, 1987, measurement of earth resistivity should be carried out annually or biannually and value should be recorded. 

What is specific resistance or resistivity of the material?

Description : What is specific resistance or resistivity of the material?

Last Answer : Specific resistance of the material is the resistance of a piece of unit length and unit cross-section (unit cube of that material). That is the resistance between the opposite faces of unit cube of the material. ... face of that material. The unit of specific resistance is Ω/cm3 , Ω/inch3 , Ω/m3 . 

A colorless salt gives violet colour to Bunsen flame and also turns moisture litmus paper blue. It is :

Description : A colorless salt gives violet colour to Bunsen flame and also turns moisture litmus paper blue. It is :

Last Answer : A colorless salt gives violet colour to Bunsen flame and also turns moisture litmus paper blue. It is : A. `Na_(2) ... C. `NaNO_(3)` D. `K_(2)CO_(3)`

(4) sodium chloride contains hygroscopic impurities like magnesium chloride Explanation: Table salt is refined salt, which contains about 97 to 99 percent sodium chloride. It usually contains substances that make it freeflowing (anticaking agents) such as sodium aluminosilicate or magnesium carbonate. Because of Hygroscopic nature of salt it become wet in rainy season as the salt absorbs moisture from environment.

Description : (4) sodium chloride contains hygroscopic impurities like magnesium chloride Explanation: Table salt is refined salt, which contains about 97 to 99 percent sodium chloride. It usually contains substances that ... of salt it become wet in rainy season as the salt absorbs moisture from environment.

Last Answer : Which of the following could be used as fuel in propellant or rockets? (1) Liquid Hydrogen + Liquid Nitrogen (2) Liquid Oxygen + Liquid Argon (3) Liquid Nitrogen + Liquid Oxygen (4) Liquid Hydrogen + Liquid Oxygen

Recipe help. What is the moisture content of white bread?

Description : Recipe help. What is the moisture content of white bread?

Last Answer : I would make the determination based on what you are doing with the croutons. Are you covering a casserole? Visually look to see if the single bag would spread out to do what you need it to do.

What is the moisture content of seeds when germination starts ?

Description : What is the moisture content of seeds when germination starts ?

Last Answer : Germination starts when seed moisture is 35-60 %.

What is the moisture content of seeds during harvesting from the field ?

Description : What is the moisture content of seeds during harvesting from the field ?

Last Answer : Seed moisture is 18-40% at harvest time .

How the moisture content of the aggregates obtainable at site affect the water content ratio specified?

Description : How the moisture content of the aggregates obtainable at site affect the water content ratio specified?

Last Answer : Obviously, if the aggregates are in a surface wet condition, meaning the moisture content is greater than the absorption, that surface water increases the water-to-cement ratio and affects strength and durability.

How do you describe the relationship between moisture content and microbial activity as the soil is gradually increased from this dry state to a saturated one What factors dictate the shape of the cur?

Description : How do you describe the relationship between moisture content and microbial activity as the soil is gradually increased from this dry state to a saturated one What factors dictate the shape of the cur?

Last Answer : Need answer

Of the following statements about the major soil types, the incorrect one is : (a) alluvial soils are easy to plough (b) red soils are rich in phosphorus, nitrogen and lime content (c) laterite is typically a soil of tropical regions which receive heavy seasonal rainfall (d) black soil is highly retentive of moisture and very productive

Description : Of the following statements about the major soil types, the incorrect one is : (a) alluvial soils are easy to plough (b) red soils are rich in phosphorus, nitrogen and lime content ( ... regions which receive heavy seasonal rainfall (d) black soil is highly retentive of moisture and very productive

Last Answer : Ans: (b)

The moisture content of a soil at which plants permanently wilt and will not recover.

Description : The moisture content of a soil at which plants permanently wilt and will not recover.

Last Answer : Ans.Permanent wilting point (PWP)

The amount of soil moisture or water content held in soil after excess water has drained away is called

Description : The amount of soil moisture or water content held in soil after excess water has drained away is called

Last Answer : Ans.Field capacity (FC)

Soil moisture content is determined by

Description : Soil moisture content is determined by

Last Answer : Ans.Tensiometer (at 0.85 bar)

Optimum moisture content for safe storage of mustard is

Description : Optimum moisture content for safe storage of mustard is

Last Answer : Ans.7-8%

The moisture content at harvesting stage of wheat

Description : The moisture content at harvesting stage of wheat

Last Answer : Ans.25-30% 3. Maize

The moisture content lines in psychrometric chart are also called as A. relative humidity lines B. specific humidity lines C. both a. and b. D. none of the above

Description : The moisture content lines in psychrometric chart are also called as A. relative humidity lines B. specific humidity lines C. both a. and b. D. none of the above

Last Answer : ANSWER : B

What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Description : What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Last Answer : ANSWER : C

Velocity of sound in air does not change with the change of – (1) Temperature of air (2) Pressure of air (3) Moisture content in air (4) Wind in the direction of propagation of sound

Description : Velocity of sound in air does not change with the change of – (1) Temperature of air (2) Pressure of air (3) Moisture content in air (4) Wind in the direction of propagation of sound

Last Answer : (2) Pressure of air Explanation: The speed of sound in an ideal gas is independent of frequency, but it weakly depends on frequency for all real physical situations. It is a function of the ... ideal gas. Sound speed is slightly dependent on pressure only because air is not quite an ideal gas.

Q No: 251 In a sludge digestion tank if the moisture content of sludge V1 litres is reduced from p1 % to p2 % the volume V2 is A. [(100 + P1)/(100 – P2)] V1 B. [(100 – P1)/(100 + P2)] V1 C. [(100 – P1)/(100 – P2)] V1 D. [(100 + P2)/(100 – P1)] V1

Description : Q No: 251 In a sludge digestion tank if the moisture content of sludge V1 litres is reduced from p1 % to p2 % the volume V2 is A. [(100 + P1)/(100 – P2)] V1 B. [(100 – P1)/(100 + P2)] V1 C. [(100 – P1)/(100 – P2)] V1 D. [(100 + P2)/(100 – P1)] V1

Last Answer : ANS: C

The moisture content of sludge is reduced from 90% to 80% in a sludge digestion tank. The percentage decrease in the volume of sludge, is A. 25 % B. 50 % C. 10 % D. 5 %

Description : The moisture content of sludge is reduced from 90% to 80% in a sludge digestion tank. The percentage decrease in the volume of sludge, is A. 25 % B. 50 % C. 10 % D. 5 %

Last Answer : ANS: B

To maintain aerobic biological activity, the moisture content of the compost mass should be about A. 45 % B. 50 % C. 55 % D. 60 %

Description : To maintain aerobic biological activity, the moisture content of the compost mass should be about A. 45 % B. 50 % C. 55 % D. 60 %

Last Answer : ANS: C

The optimum moisture content in solids to be crushed/ground ranges from __________ percent. (A) 3 to 4 (B) 8 to 10 (C) 10 to 15 (D) 15 to 20

Description : The optimum moisture content in solids to be crushed/ground ranges from __________ percent. (A) 3 to 4 (B) 8 to 10 (C) 10 to 15 (D) 15 to 20

Last Answer : (A) 3 to 4

The specific gravity of coal depends mainly on its __________ content. (A) Carbon (B) Volatile matter (C) Ash (D) Moisture

Description : The specific gravity of coal depends mainly on its __________ content. (A) Carbon (B) Volatile matter (C) Ash (D) Moisture

Last Answer : (C) Ash

During drying of a solid, the critical moisture content increases with (A) Decreased drying rate (B) Increased thickness of the solid (C) Increased drying rate (D) Both (B) and (C)

Description : During drying of a solid, the critical moisture content increases with (A) Decreased drying rate (B) Increased thickness of the solid (C) Increased drying rate (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Drying operation under vacuum is carried out to (A) Dry those materials which have very high unbound moisture content (B) Reduce drying temperature (C) Increase drying temperature (D) Dry materials having high bound moisture content

Description : Drying operation under vacuum is carried out to (A) Dry those materials which have very high unbound moisture content (B) Reduce drying temperature (C) Increase drying temperature (D) Dry materials having high bound moisture content

Last Answer : (B) Reduce drying temperature

If moisture content of solid on dry basis is X, then the same on wet basis is (A) X/(X + 1) (B) X/(1 - X) (C) (1 + X)/X (D) (1 - X)/X

Description : If moisture content of solid on dry basis is X, then the same on wet basis is (A) X/(X + 1) (B) X/(1 - X) (C) (1 + X)/X (D) (1 - X)/X

Last Answer : (A) X/(X + 1)

Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a distillation column (C) Separation of components is not possible in liquid extraction, if selectivity is unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Description : Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a ... unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Last Answer : (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Pick out the correct statement. (A) Bound moisture is removed during constant rate drying period (B) Free moisture is removed during falling rate drying period (C) The sum of free moisture and equilibrium moisture in a solid is called the critical moisture (D) The driving force for mass transfer in a wet solid is its free moisture content

Description : Pick out the correct statement. (A) Bound moisture is removed during constant rate drying period (B) Free moisture is removed during falling rate drying period (C) The sum of free moisture and ... (D) The driving force for mass transfer in a wet solid is its free moisture content

Last Answer : (D) The driving force for mass transfer in a wet solid is its free moisture content

Advantage of continuous drying over batch drying is that the (A) Drying cost per unit weight of dried product is less (B) Product with more uniform moisture content is produced (C) Equipment size required is smaller (D) All 'a', 'b' & 'c'

Description : Advantage of continuous drying over batch drying is that the (A) Drying cost per unit weight of dried product is less (B) Product with more uniform moisture content is produced (C) Equipment size required is smaller (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

It takes 6 hours to dry a wet solid from 50% moisture content to the critical moisture content of 15%. How much longer it will take to dry the solid to 10% moisture content, under the same drying conditions? (The equilibrium moisture content of the solid is 5%). (A) 15 min (B) 51 min (C) 71 min (D) 94 min

Description : It takes 6 hours to dry a wet solid from 50% moisture content to the critical moisture content of 15%. How much longer it will take to dry the solid to 10% moisture content, under the same drying conditions? (The ... 5%). (A) 15 min (B) 51 min (C) 71 min (D) 94 min

Last Answer : (C) 71 min

Pick out the wrong statement: (A) Change in barometric pressure does not affect the relative humidity (B) In case of a packed tower, the operating velocity is about half of the flooding velocity, generally (C) 'Elution' means the desorption of the adsorbed solute by a solvent (D) The equilibrium moisture content of the solid can be reduced by increasing the absolute humidity

Description : Pick out the wrong statement: (A) Change in barometric pressure does not affect the relative humidity (B) In case of a packed tower, the operating velocity is about half of the ... (D) The equilibrium moisture content of the solid can be reduced by increasing the absolute humidity

Last Answer : (D) The equilibrium moisture content of the solid can be reduced by increasing the absolute humidity

The critical moisture content in case of drying indicates the __________ rate period. (A) Beginning of falling (B) Beginning of constant (C) End of falling (D) None of these

Description : The critical moisture content in case of drying indicates the __________ rate period. (A) Beginning of falling (B) Beginning of constant (C) End of falling (D) None of these

Last Answer : (A) Beginning of falling

The drying time between fixed moisture content within diffusion controlled 'falling rate period' is proportional to (assuming that drying occurs from all surfaces of the solid) (where, T = thickness of the solid). (A) √T (B) T (C) T 2 (D) T

Description : The drying time between fixed moisture content within diffusion controlled 'falling rate period' is proportional to (assuming that drying occurs from all surfaces of the solid) (where, T = thickness of the solid). (A) √T (B) T (C) T 2 (D) T

Last Answer : (C) T

Moisture content of a substance when at equilibrium with a given partial pressure of the vapour is called the __________ moisture. (A) Free (B) Unbound (C) Equilibrium (D) Bound

Description : Moisture content of a substance when at equilibrium with a given partial pressure of the vapour is called the __________ moisture. (A) Free (B) Unbound (C) Equilibrium (D) Bound

Last Answer : (C) Equilibrium

Dried finished product sampled from various parts of a __________ dryer exhibits non-uniformity in the moisture content. (A) Rotary (B) Tray (C) Freeze (D) None of these

Description : Dried finished product sampled from various parts of a __________ dryer exhibits non-uniformity in the moisture content. (A) Rotary (B) Tray (C) Freeze (D) None of these

Last Answer : (B) Tray

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

The slow rate of decomposition of fallen logs in nature is due to their (a) anaerobic environment around them (b) low cellulose content (c) low moisture content (d) poor nitrogen content.

Description : The slow rate of decomposition of fallen logs in nature is due to their (a) anaerobic environment around them (b) low cellulose content (c) low moisture content (d) poor nitrogen content.

Last Answer : (d) poor nitrogen content.

Stored grains can be saved from insect damage, if the grain moisture content is — (A) <> 10% (C) 10% (D) None of these

Description : Stored grains can be saved from insect damage, if the grain moisture content is — (A) 10% (C) 10% (D) None of these

Last Answer : (C) 10%

Maximum moisture content for safe storage in wheat seed is (a) 12 (b) 15 (c) 7 (d) 20

Description : Maximum moisture content for safe storage in wheat seed is (a) 12 (b) 15 (c) 7 (d) 20

Last Answer : (a) 12