Description : Clamp coupling employ bolts. a) True b) False
Last Answer : a) True
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False
Last Answer : b) False
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No
Last Answer : b) No
Description : In case of clamp coupling, power is transmitted by means of, (A) Friction force (B) Shear resistance (C) Crushing resistance (D) None of the above
Last Answer : (A) Friction force
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : Clutch and coupling can be considered to be same. a) True b) False
Description : Power is transmitted by only in rigid flange coupling. a) True b) False
Description : A machine started malfunctioning due to some issues with the coupling. The coupling emplaced in the machine was Oldham. The only coupling available in the workshop is Hooke’s coupling. So Oldham coupling can be replaced by Hooke’s coupling. a) True b) False
Description : Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False
Description : A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False
Description : Flange coupling is rigid types coupling. A. True B. False
Last Answer : A. True
Description : Universal coupling is rigid types coupling. A. True B. False
Last Answer : B. False
Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses
Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical
Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.
Last Answer : (d) never be across the threaded portion
Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed
Last Answer : d) None of the listed
Description : Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated
Last Answer : b) Tap Bolts
Description : If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned
Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener
Last Answer : d) Helps in locking of the fastener
Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)
Last Answer : (A) Approaches yield point
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs
Last Answer : (C) Used to prevent relative motion between parts
Description : What Is The Empirical Formula Used To Give The Number Of Bolts In Flange Coupling?
Last Answer : n = 0.2d + 3
Description : Actual stress in the bolts of a flanged coupling of a shaft will be (a) More than the designed strength (b) Less than the designed strength (c) Neither more nor less than the designed strength (d) None
Last Answer : (b) Less than the designed strength
Description : The split - pin is used in... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Last Answer : B. Knuckle joint
Description : The joints between link of a suspension bridge, which of the following joints used.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : To joining the links of a bicycle chain which of the following joint is used. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : Forked - pin joints is also called as... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint
Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed
Last Answer : b) 1102.8N
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle
Last Answer : A. Which are perfectly aligned