Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Which of the following are good for parts that are seldom dismantled.

a) Through Bolts

b) Tap Bolts

c) Studs

d) Cannot be stated
by

1 Answer

Answer :

b) Tap Bolts
by

Related questions

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Description : If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Last Answer : b) Tap Bolts

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

Which of the following requires more space for the rotation of spanner? a) Square Head b) Hexagonal Head c) Both require equal space of rotation d) Cannot be stated

Description : Which of the following requires more space for the rotation of spanner? a) Square Head b) Hexagonal Head c) Both require equal space of rotation d) Cannot be stated

Last Answer : a) Square Head

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

Fitted bearing must be partial bearing. a) True b) No c) No lubricating space is required d) Can’t be stated

Description : Fitted bearing must be partial bearing. a) True b) No c) No lubricating space is required d) Can’t be stated

Last Answer : a) True

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Last Answer : b) No, fusion doesn’t require

Why has NASA been dismantled?

Description : Why has NASA been dismantled?

Last Answer : NASA is not being disassembled.

What would happen if Americas military were dismantled?

Description : What would happen if Americas military were dismantled?

Last Answer : Well, there would be many fewer technological advances that trickled down to the civilians. Like, oh, say, the internet.

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (d) Cage

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact

A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (D) Where there is no lubricant

Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Last Answer : b) Corrosive

A spring of stiffness constant k is cut in two equal parts. The stiffness constant of new spring will be k/2. a) True b) False

Description : A spring of stiffness constant k is cut in two equal parts. The stiffness constant of new spring will be k/2. a) True b) False

Last Answer : b) False

Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Description : Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Last Answer : D. All of the above

Different parts of a weld symbol are (i) Arrow, center line and back part (ii) Arrow, body line and length (iii) Arrow, body line and tail (iv)None

Description : Different parts of a weld symbol are (i) Arrow, center line and back part (ii) Arrow, body line and length (iii) Arrow, body line and tail (iv)None

Last Answer : (iii) Arrow, body line and tail

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Last Answer : b) No, it is done up to plastic stage

Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Description : Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Last Answer : d) Each of the mentioned

Cold riveting holds the connected parts better than hot riveting. a) True b) False

Description : Cold riveting holds the connected parts better than hot riveting. a) True b) False

Last Answer : b) False

The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Last Answer : (D) All three factors

Stressed parts are always kept in tension. a) True b) False

Description : Stressed parts are always kept in tension. a) True b) False

Last Answer : a) True

When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Last Answer : b) Split flywheel

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Description : If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Last Answer : a) Hydrostatic

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed