Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Setscrews are

(A) Similar to tap bolts except that a greater variety of shapes of heads are available

(B) Slotted for screw driver and generally used with a nut

(C) Used to prevent relative motion between parts

(D) Similar to studs
by

1 Answer

Answer :

(C) Used to prevent relative motion between parts
by

Related questions

If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Description : If there is no place to accommodate the nut, then one would choose the a) Through Bolts b) Tap Bolts c) Studs d) None of the mentioned

Last Answer : b) Tap Bolts

Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Description : Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated

Last Answer : b) Tap Bolts

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Last Answer : b) False

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

do i need to screw into studs?

Description : do i need to screw into studs?

Last Answer : You can screw this into a single wood stud, concrete block,concrete or metal studs.

Why does the slotted screw persist?

Description : Why does the slotted screw persist?

Last Answer : You can’t pry open a paint can or putty container with a Phillip’s screwdriver.

Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub

Last Answer : (D) There is relative motion between shaft and hub

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

Clamp coupling employ bolts. a) True b) False

Description : Clamp coupling employ bolts. a) True b) False

Last Answer : a) True

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

Feather key can be used to prevent axial motion between two elements. a) True b) False

Description : Feather key can be used to prevent axial motion between two elements. a) True b) False

Last Answer : b) False

What is type of nut and bolts are used in IPBD?

Description : What is type of nut and bolts are used in IPBD?  

Last Answer : Non-magnetic stainless steel nut and bolts are used in IPBD to restrict magnetic effect at joints.  

When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing stress is more than crushing stress induced in the threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads

The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Last Answer : (B) Making shank diameter equal to core diameter of threads

Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d

Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d

Last Answer : (A) h = 0.4 d

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Description : The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Last Answer : (B) More than the nut size

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Last Answer : a) Dog Point

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Last Answer : a) 50%

Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Last Answer : a) decreases

Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Last Answer : b) False

Efficiency of screw depends upon lead of the screw. a) True b) False

Description : Efficiency of screw depends upon lead of the screw. a) True b) False

Last Answer : a) True

Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Last Answer : b) False

Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Last Answer : d. all of the above

Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Last Answer : (C) Cap screw with hexagonal socket head

A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Description : A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Last Answer : (A) Major diameter

The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Description : The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Last Answer : (A) Major diameter

The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Last Answer : (A) (1 - sinφ)/ (1 + sinφ)