Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs
Last Answer : (C) Used to prevent relative motion between parts
Description : Which of the following are good for parts that are seldom dismantled. a) Through Bolts b) Tap Bolts c) Studs d) Cannot be stated
Last Answer : b) Tap Bolts
Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt
Last Answer : b. Set screws
Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener
Last Answer : d) Helps in locking of the fastener
Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer
Last Answer : (B) Making shank diameter equal to core diameter of threads
Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface
Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut
Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.
Last Answer : (d) never be across the threaded portion
Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses
Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical
Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed
Last Answer : d) None of the listed
Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)
Last Answer : (A) Approaches yield point
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : Clamp coupling employ bolts. a) True b) False
Last Answer : a) True
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : What is type of nut and bolts are used in IPBD?
Last Answer : Non-magnetic stainless steel nut and bolts are used in IPBD to restrict magnetic effect at joints.
Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False
Last Answer : b) False
Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above
Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads
Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d
Last Answer : (A) h = 0.4 d
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (A) h = 0.5 dc
Description : The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size
Last Answer : (B) More than the nut size
Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (B) h = 0.25 dc
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : Self-locking takes place when a) Coefficient of friction is equal to or greater than the tangent of the helix angle b) Coefficient of friction is lesser than or equal to the tangent of the helix ... friction is equal to or greater than the tangent of the helix angle d) None of the mentioned
Last Answer : c) Coefficient of friction is equal to or greater than the tangent of the helix angle
Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned
Last Answer : b) 40/9
Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned
Last Answer : (c) They create very less noise
Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned
Last Answer : b) They create very less noise
Description : ________ captive requires that the cloud accommodate multiple compliance regimes. a) Licensed b) Policy-based c) Variable d) All of the mentioned
Last Answer : Policy-based
Description : Point out the correct statement. a) Google's cloud includes perhaps some 10 data centers worldwide b) Flipkart.com's infrastructure was built to support elastic demand so the system could accommodate ... ) Data centers have been sited to optimize the overall system latency d) All of the mentioned
Last Answer : Data centers have been sited to optimize the overall system latency
Description : Can I use my earring studs in place of a nose ring?
Last Answer : Yes, as long as they are the same size you can interchange earring studs and nose ring studs.
Description : What were the steps taken by the government of Belgium to accommodate different ethnic groups? (a) Constitution prescribes that the number of Dutch and French speaking ministers should be equal in the central government. (b) The government ... and (b) 2(b) and (c) 3 (c) and (d) 4 (a) and (d)
Last Answer : 4 (a) and (d)
Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned
Last Answer : b) Governor
Description : The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned
Last Answer : (d) all of the mentioned
Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned
Last Answer : (d) None of the mentioned
Description : What type of bearing will you recommend for use in the conveyor belt roller? (a) Ball-bearing (b) Roller bearing (c) Magnetic bearing (d) None of the mentioned
Last Answer : (b) Roller bearing
Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned
Last Answer : (b) separable
Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned
Last Answer : (c) Spherical roller thrust bearings and taper roller bearings
Description : Antifriction bearings are (a) sleeve bearings (b) hydrodynamic bearings (c) thin lubricated bearings (d) none of the mentioned
Last Answer : (d) none of the mentioned
Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned
Last Answer : (a) minimum expected life
Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned
Last Answer : (c) both radial and axial loads
Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned
Last Answer : (d) all the mentioned
Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned
Description : Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned
Last Answer : a) Completely