Magnetic crack detection method in the welds is destructible examination. a) True b) False

Magnetic crack detection method in the welds is destructible examination.

a) True

b) False
by

1 Answer

Answer :

b) False
by

Related questions

Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Description : Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Last Answer : b) False

Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Last Answer : (i) Shear stress

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4

Description : While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4

Last Answer : b) None of the listed

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t

Description : Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t

Last Answer : c) 250000 t

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Last Answer : a) My/I

For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of the bolts to prevent leakage. c) Immediate replacement is recommended if the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Description : For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of ... the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Last Answer : b) Periodic tightening of the bolts to prevent leakage.

Testing of welds by a) Dye penetrant test b) Magnetic particle inspection c) Radiographic inspection d) All the above*

Description : Testing of welds by a) Dye penetrant test b) Magnetic particle inspection c) Radiographic inspection d) All the above*

Last Answer : d) All the above

Select the wrong statement. (a) The walls of diatoms are easily destructible. (b) ‘Diatomaceous earth’ is formed by the cell walls of diatoms. (c) Diatoms are chief producers in the oceans. (d) Diatoms are microscopic and float passively in water.

Description : Select the wrong statement. (a) The walls of diatoms are easily destructible. (b) ‘Diatomaceous earth’ is formed by the cell walls of diatoms. (c) Diatoms are chief producers in the oceans. (d) Diatoms are microscopic and float passively in water.

Last Answer : (a) The walls of diatoms are easily destructible.

The law of conservation of mass states that ______.  a. mass is indestructible  b. mass is destructible  c. mass is indestructible  d. none of the above

Description : The law of conservation of mass states that ______.  a. mass is indestructible  b. mass is destructible  c. mass is indestructible  d. none of the above

Last Answer : mass is indestructible

Self-Examination Is Key In Early Detection Of Testicular Cancer?

Description : Self-Examination Is Key In Early Detection Of Testicular Cancer?

Last Answer : Contact your physician if you notice any lumps or changes to your testicles or scrotum. Regular self-exams and early detection is essential for the successful treatment of testicular cancer. Some symptoms ... scrotumpain, discomfort, or a dull ache in the testicle, groin, scrotum, or lower abdomen

Keyed joints never lead to stress concentration on shafts. a) True b) False

Description : Keyed joints never lead to stress concentration on shafts. a) True b) False

Last Answer : b) False

Feather key can be used to prevent axial motion between two elements. a) True b) False

Description : Feather key can be used to prevent axial motion between two elements. a) True b) False

Last Answer : b) False

The operation of flywheel is continuous. a) True b) False

Description : The operation of flywheel is continuous. a) True b) False

Last Answer : a) True

Flywheel and governor can be interchanged. a) True b) False

Description : Flywheel and governor can be interchanged. a) True b) False

Last Answer : b) False

Flywheels are used in punching and shear operation. a) True b) False

Description : Flywheels are used in punching and shear operation. a) True b) False

Last Answer : a) True

Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False

Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False

Last Answer : a) True

The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False

Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False

Last Answer : (b) False

For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False

Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False

Last Answer : (a) True

The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False

Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False

Last Answer : (b) False

Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Last Answer : (b) False

Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False

Last Answer : (b) False

A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Last Answer : (a) True

Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Last Answer : (b) False

A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False

Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False

Last Answer : (b) False

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Last Answer : (b) False

Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is generated by the rotation of the journal. [IES-1998] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true

Last Answer : (a) Both A and R are individually true and R is the correct explanation of A

Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (c) A is true but R is false

Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the journal. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal bearings balances the load on the journal. (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true

Last Answer : (a) Both A and R are true and R is the correct explanation of A

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False

Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False

Last Answer : a) True

Hydrostatic and hydrodynamic lubrication are the same thing. a) True b) False

Description : Hydrostatic and hydrodynamic lubrication are the same thing. a) True b) False

Last Answer : b) False

Hydrodynamic bearing is a self-acting bearing. a) True b) False

Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False

Last Answer : a) True

Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Last Answer : b) False

The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False

Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False

Last Answer : b) False

For majority of bearings, actual life is considerably greater than rated life. a) True b) False

Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False

Last Answer : a) True

The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False

Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False

Last Answer : b) False

Stribeck equation gives dynamic load capacity of the bearing. a) True b) False

Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False

Last Answer : b) False

A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False

Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False

Last Answer : a) True

Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False

Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False

Last Answer : b) False

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Last Answer : b) False