When two Belleville sprigs are arranged in series, half deflection is obtained for same force. a) One fourth deflection b) Double deflection c) Four time deflection d) None of the listed

When two Belleville sprigs are arranged in series, half deflection is obtained for same force.

a) One fourth deflection

b) Double deflection

c) Four time deflection

d) None of the listed
by

1 Answer

Answer :

b) Double deflection
by

Related questions

When two Belleville sprigs are arranged in series, half deflection is obtained for same force. (a) One fourth deflection (b) Double deflection (c) Four time deflection (d) None of the listed

Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. (a) One fourth deflection (b) Double deflection (c) Four time deflection (d) None of the listed

Last Answer : (b) Double deflection

When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Last Answer : b) Double force

When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined

Last Answer : (b) Double force

The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Description : The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Last Answer : (C) Belleville (coned disk) spring

Belleville spring can only produce linear load deflection characteristics. a) Only linear b) Linear as well as non linear c) Non-linear d) None of the mentioned

Description : Belleville spring can only produce linear load deflection characteristics. a) Only linear b) Linear as well as non linear c) Non-linear d) None of the mentioned

Last Answer : b) Linear as well as non linear

When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Description : When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Last Answer : (B) Double of original spring

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Surge is a desirable effect in the sprigs. a) True b) False

Description : Surge is a desirable effect in the sprigs. a) True b) False

Last Answer : b) False

The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Description : The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Last Answer : (C) Both (A) and (B)

The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Description : The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Last Answer : (B) Multi-leaf spring

Belleville spring can be used in clutch application. a) True b) False

Description : Belleville spring can be used in clutch application. a) True b) False

Last Answer : a) True

For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Last Answer : b) False

If the distance between two charges is halved, then the force between them becomes (a) Half (b) Double (c) Four times (d) One-fourth

Description : If the distance between two charges is halved, then the force between them becomes (a) Half (b) Double (c) Four times (d) One-fourth

Last Answer : Ans:(c)

For two springs connected in series, the net deflection is equal to the sum of deflection in two springs. a) True b) False

Description : For two springs connected in series, the net deflection is equal to the sum of deflection in two springs. a) True b) False

Last Answer : a) True

The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Last Answer : (c)Belleville spring

Belleville spring can only produce linear load deflection characteristics. (a) Only linear (b) Linear as well as non linear (c) Non-linear (d) None of the mentioned

Description : Belleville spring can only produce linear load deflection characteristics. (a) Only linear (b) Linear as well as non linear (c) Non-linear (d) None of the mentioned

Last Answer : (b) Linear as well as non linear

The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Description : The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Last Answer : (D) all of the above

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

Can concentric springs be used to obtain a force which is not proportional to its deflection? a) True b) False

Description : Can concentric springs be used to obtain a force which is not proportional to its deflection? a) True b) False

Last Answer : a) True

Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Last Answer : d) All of the listed

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Last Answer : b) No, it is done up to plastic stage

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008] (a) Remains unchanged (b) Gets doubled (c) Gets reduced to one-fourth of original value (d) Gets reduced to half of original value

Description : A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008 ... Gets reduced to one-fourth of original value (d) Gets reduced to half of original value

Last Answer : (a) Remains unchanged

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

If a copper wire is increased to double its length, its resistance will become – (1) four times (2) one-fourth (3) double (4) half

Description : If a copper wire is increased to double its length, its resistance will become – (1) four times (2) one-fourth (3) double (4) half

Last Answer : (3) double Explanation: There is a direct relationship between the amount of resistance encountered by charge and the length of wire it must traverse. After all, if resistance occurs as the result of collisions ... the atoms of the wire, then there is likely to be more collisions in a longer wire.

If a copper wire is increased to double its length, its resistance will become (1) four times (2) one–fourth (3) double (4) half

Description : If a copper wire is increased to double its length, its resistance will become (1) four times (2) one–fourth (3) double (4) half

Last Answer : double

When the speed of car is doubled, then what will be the braking force of the car to stop it in the same distance? (1) four times (2) two times (3) half (4) one-fourth

Description : When the speed of car is doubled, then what will be the braking force of the car to stop it in the same distance? (1) four times (2) two times (3) half (4) one-fourth

Last Answer : (1) four times Explanation: Brake force, also known as Brake Power, is a measure of braking power of a vehicle. Suppose a car whose mass is 'x' and is braked from a speed of y km/hr to come to ... the car is four times the original speed i.e. '4v'. Note that all the parameters remain to be same.

When the speed of car is doubled, then what will be the braking force of the car to stop it in the same distance ? (1) four times (2) two times (3) half (4) one-fourth

Description : When the speed of car is doubled, then what will be the braking force of the car to stop it in the same distance ? (1) four times (2) two times (3) half (4) one-fourth

Last Answer :  four times

A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

Last Answer : (c) 689.7N and 4310.3N

A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant

A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact

A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (D) Where there is no lubricant

The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Description : The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Last Answer : (A) Pδ/2

The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ

Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ

Last Answer : b) 8PDɜN/Gd4

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Last Answer : a) My/I

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Which of the following are functions of flywheel? a) Store and release energy during work cycle b) Reduce power capacity of the electric motor c) Reduce amplitude of speed fluctuations d) All of the listed

Description : Which of the following are functions of flywheel? a) Store and release energy during work cycle b) Reduce power capacity of the electric motor c) Reduce amplitude of speed fluctuations d) All of the listed

Last Answer : d) All of the listed

An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Description : An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Last Answer : (d) all of the listed

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Last Answer : (a) minimum expected life

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Last Answer : a) Race rotation factor

Which of the following is expression for stribeck equation?(Number of balls=z)? a) C=kd2z/5 b) C=kd2z/15 c) C=kd2z/10 d) None of the listed

Description : Which of the following is expression for stribeck equation?(Number of balls=z)? a) C=kd2z/5 b) C=kd2z/15 c) C=kd2z/10 d) None of the listed

Last Answer : a) C=kd2z/5

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary