Current in a 60 W light bulb when it is connected to a 230 V power supply is A. 0.26 A B. 1.5 A C. 2.6 A D. 3.9 A

Current in a 60 W light bulb when it is connected to a 230 V power

supply is

A. 0.26 A

B. 1.5 A

C. 2.6 A

D. 3.9 A
by

1 Answer

Answer :

0.26 A


by

Related questions

A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Description : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Last Answer : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is ... Omega` B. `46 Omega` C. `26Omega` D. `13 Omega`

Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out

Description : Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out

Last Answer : Three 60 W bulbs are in parallel across the 230 V power line. If one bulb burns out the other two bulbs will remain glowing

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Description : Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Last Answer : a. 40 W bulb

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses

Description : Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

Last Answer : Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume 90 W

The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated

Description : The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor ... Hz supply is  (A) 58.5 A (B) 45.0 A (C) 42.7 A (D) 55.6 A

Last Answer : The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor is connected to a 236 , V 57 Hz supply is 45.0 A 

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Description : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Last Answer : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open the other two bulbs will light.

The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor isA. 15.6 WB. 15 WC. 16 WD. 17 W

Description : Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor is A. 15.6 W B. 15 W C. 16 W D. 17 W

Last Answer : 15.6 W

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... B. 160 W C. `37.5 W` D. 60 W

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... `37.5` W B. 75W C. 80W D. 40 W

Ionisation potential applied across the electrodes of electrostatic tar precipitator is around (A) 230 V AC (B) 60 KV AC (C) 230 V DC (D) 60 KV DC

Description : Ionisation potential applied across the electrodes of electrostatic tar precipitator is around (A) 230 V AC (B) 60 KV AC (C) 230 V DC (D) 60 KV DC

Last Answer : (D) 60 KV DC

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Last Answer : ANSWER: Z -- 3 AMPERES

The resistance of a 230 V, 100 W lamp is

Last Answer : The resistance of a 230 V, 100 W lamp is 529 Ω.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : (C) 3.0 V.

Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : A:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the Bulb (P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Description : The required DC voltage for arc welding is- (1) 6 to 9 V (2) 50 to 60 V (3) 200 to 250 V (4) 90 to 100 V

Last Answer : (3) 200 to 250 V

A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.

Description : A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.

Last Answer : A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a ... is `1.7xx10^(-4) "per"^(@)C`.

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Description : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Last Answer : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes

If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps

Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps

Last Answer : Answer: B

change light bulb in kenmore dryer 26-94052

Description : change light bulb in kenmore dryer 26-94052

Last Answer : Need Answer

For a parallel connection of light bulbs, which of the following statements is correct? w) The resistance of each light bulb must be the same. x) If one goes out they all go out. y) Each of the light bulbs operates independently.

Description : For a parallel connection of light bulbs, which of the following statements is correct? w) The resistance of each light bulb must be the same. x) If one goes out they all go out. y) Each of the light bulbs operates independently.

Last Answer : ANSWER: Y -- EACH OF THE LIGHT BULBS OPERATES INDEPENDENTLY.

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave

Description : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

Last Answer : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is 1.0 A

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be 3.0 V.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary ...

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be: 3.0 V

Three resistors which have different values are connected in series. Which one of the following statements is correct? w) The potential drop across all three resistors is the same. x) The same current passes through all three resistors. y) The same power is dissipated by all three resistors.

Description : Three resistors which have different values are connected in series. Which one of the following statements is correct? w) The potential drop across all three resistors is the same. x) The same current passes through all three resistors. y) The same power is dissipated by all three resistors. 

Last Answer : ANSWER: X -- THE SAME CURRENT PASSES THROUGH ALL THREE RESISTORS. 

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by...

Description : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

Last Answer : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will increase.

Two incandescent light bulbs of 40 W and 60 W rating are connected in series across the mains, then

Description : Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then .  A) The bulbs together consume 100 W B) The bulbs together consume 50 W C) The 60 W bulb glows brighter D) The 40 W bulb glows brighter

Last Answer : Two incandescent light bulbs of 40 Wand 60 W rating are connected in series across the mains, then . The bulbs together consume 50 W 

Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Description : Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Last Answer : ANSWER: 1.25 AMPS 

What happen if we give 220 volts dc supply to the bulb or tube light?

Description : What happen if we give 220 volts dc supply to the bulb or tube light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Description : What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

what happens if we give 220 volts dc supply to the bulb or tube light?

Description : what happens if we give 220 volts dc supply to the bulb or tube light?

Last Answer : A:Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current ... be so high that it may damage the bulb element. Low dc voltage will not damage the appliances

What happen if we give 220 volts dc supply to bulb or tube light?

Description : What happen if we give 220 volts dc supply to bulb or tube light?

Last Answer : Bulbs or devices for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Description : What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Last Answer : Answer: C

How many wires are normally connected to a double- filament light bulb?

Description : How many wires are normally connected to a double- filament light bulb?

Last Answer : 5

A cyclist riding a cycle fitted with a dynamo to a tyre gets bright light in the bulb connected, when he pedals fast. Why?

Description : A cyclist riding a cycle fitted with a dynamo to a tyre gets bright light in the bulb connected, when he pedals fast. Why?

Last Answer : More magnetic lines of force change with respect to the coil, leading to more current being produced.

One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter...

Description : One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant is 400 rev/kWh. The power factor of the load is

Last Answer : One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant is 400 rev/kWh. The power factor of the load is 0.8

A 60 watt light bulb runs for 5 seconds how much energy does it use?

Description : A 60 watt light bulb runs for 5 seconds how much energy does it use?

Last Answer : 300 j of energy

In a filament type light bulb most of the electric power consumed appears as – (1) visible light (2) infra-red rays (3) ultra-violet rays (4) fluorescent light

Description : In a filament type light bulb most of the electric power consumed appears as – (1) visible light (2) infra-red rays (3) ultra-violet rays (4) fluorescent light

Last Answer : (2) infra-red rays Explanation: When electricity is passed through the filament, the filament gets hot. Depending on the temperature of the filament, radiation is emitted from the filament. The ... energy converts into visible light and rest of it is emitted as heat or infrared radiation.