A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.

A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.
by

1 Answer

Answer :

A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a ... is `1.7xx10^(-4) "per"^(@)C`.
by
selected by

Related questions

A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady

Description : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of   (a) 250A (b) 50 A (c) 150 A (d) 350 A 

Last Answer : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of 250A

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is

Description : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately? A.385 ohms B.38.5ohms C.3.1 ohms D.31 ohms

Last Answer : 31ohns

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately...

Description : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: A. 385Ω B. 38.5Ω C. 3.1Ω D. 31Ω

Last Answer : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: 31Ω

An electric toaster uses nichrome for its heating element. When a negligibly small current passes through it. It resistance at room temperature `(27.0

Description : An electric toaster uses nichrome for its heating element. When a negligibly small current passes through it. It resistance at room temperature `(27.0

Last Answer : An electric toaster uses nichrome for its heating element. When a negligibly small current passes through it. ... range involved , `1.70xx10^-4C^-1`

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Heating element of an electric heater is made up of _____? A. Tungsten B. Graphite C. Chromium 26 D. Nichrome

Description : Heating element of an electric heater is made up of _____? A. Tungsten B. Graphite C. Chromium 26 D. Nichrome

Last Answer : ANSWER: D

The heating element in an electric iron is made of (a) Nichrome (b) Tungsten (c) Copper (d) Iron

Description : The heating element in an electric iron is made of (a) Nichrome (b) Tungsten (c) Copper (d) Iron

Last Answer : Ans:(a)

Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Description : Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Last Answer : Ans:(d)

An electric iron has a heating element made of – (1) Copper (2) Tungsten (3) Nichrome (4) Zinc

Description : An electric iron has a heating element made of – (1) Copper (2) Tungsten (3) Nichrome (4) Zinc

Last Answer : (3) Nichrome Explanation: Nichrome is used in electric iron because it has high resistance and it is stable in air when hot. Nichrome wire forms a protective layer of chromium oxide. Chemically it is quite stable and does not combine with other atmospheric gases even in high temperature.

Heating element of an electric heater is made up of------? A. Tungsten B. Graphite C. Chromium D. Nichrome (Answer)

Description : Heating element of an electric heater is made up of------? A. Tungsten B. Graphite C. Chromium D. Nichrome (Answer)

Last Answer : D. Nichrome (Answer)

__________ wire is never used for making the heating element. (A) Nichrome (B) Kanthal (C) Invar (D) None of these

Description : __________ wire is never used for making the heating element. (A) Nichrome (B) Kanthal (C) Invar (D) None of these

Last Answer : (C) Invar

An electric iron has a heating element made of : (1) Copper (2) Tungsten (3) Nichrome (4) Zinc

Description : An electric iron has a heating element made of : (1) Copper (2) Tungsten (3) Nichrome (4) Zinc

Last Answer : Nichrome

An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Last Answer : Answer: D

A heating element of a hot plate on an electric cooking range draws 12...

Description : A heating element of a hot plate on an electric cooking range draws 12 amperes from 240 V mains. How many kWh of energy will be consumed in one hour and 15 minutes 

Last Answer : A heating element of a hot plate on an electric cooking range draws 12 amperes from 240 V mains. 3.2 kWh of energy will be consumed in one hour and 15 minutes. 

Does anyone know what happened to Golden-Shellback? Supposedly a company developed a technique for waterproofing electronic gadgets, but after a lot of intial hype and media attention, they seem to have disappeared. Where'd they go?

Description : Does anyone know what happened to Golden-Shellback? Supposedly a company developed a technique for waterproofing electronic gadgets, but after a lot of intial hype and media attention, they seem to have disappeared. Where'd they go?

Last Answer : I remember them, but their treatment was really expensive. There were youtube clips of an iphone playing songs under water, even using the screen to navigate to show it wasn't a dummy phone. That's ... and Gorilla Glass. Then I wouldn't be so paranoid about dropping it in a rain puddle : )

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to...

Description : A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate ... power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

Last Answer : 572var

An alloy used in making heating elements for electric heating device is - (1) Solder (2) Alloy Steel (3) Nichrome (4) German Silver

Description : An alloy used in making heating elements for electric heating device is - (1) Solder (2) Alloy Steel (3) Nichrome (4) German Silver

Last Answer : (3) Nichrome Explanation: Nichrome is a mixture of chromium and nickel. Nichrome wire is a great conductor of electricity. Nichrome is used to make heating coils and other types of elements in household appliances.

Which of the following metals is used for the manufacture of heating elements provided in electric iron? (1) Nickel (2) Chromium (3) Nichrome (4) Tungsten

Description : Which of the following metals is used for the manufacture of heating elements provided in electric iron? (1) Nickel (2) Chromium (3) Nichrome (4) Tungsten

Last Answer : (3) Nichrome Explanation: Nichrome is the most common domestic heating element and is found in many household products. Commonly, items such as toasters, hair dryers and heaters use nichrome coils to ... percent nickel and 20 percent chromium, and its high melting point of 1,400 degrees Celsius.

High resistance electrical heating elements/wire are not made of (A) Maraging steel (B) Nimonic alloys (C) Kanthal wire (D) Nichrome

Description : High resistance electrical heating elements/wire are not made of (A) Maraging steel (B) Nimonic alloys (C) Kanthal wire (D) Nichrome

Last Answer : (A) Maraging steel

The heating elements of electric irons are made of (A) Copper. (B) Nichrome. (C) Constantan. (D) Aluminium.

Description : The heating elements of electric irons are made of (A) Copper. (B) Nichrome. (C) Constantan. (D) Aluminium.

Last Answer : (B) Nichrome.

An alloy used in making heating elements for electric heating device is (1) Solder (2) Alloy Steel (3) Nichrome (4) German Silver

Description : An alloy used in making heating elements for electric heating device is (1) Solder (2) Alloy Steel (3) Nichrome (4) German Silver

Last Answer : Nichrome

Which of the following metals is used for the manufacture of heating elements provided in electric iron ? (1) Nickel (2) Chromium (3) Nichrome (4) Tungsten

Description : Which of the following metals is used for the manufacture of heating elements provided in electric iron ? (1) Nickel (2) Chromium (3) Nichrome (4) Tungsten

Last Answer : Nichrome

What is the power of a portable radio that operates on 24 v two 12 v batteries in series and draws 2.2 a current?

Description : What is the power of a portable radio that operates on 24 v two 12 v batteries in series and draws 2.2 a current?

Last Answer : The power in this case is equal to the voltage, times thecurrent. Because of the units used, the answer will be inwatts.

A graphing calculator uses a 6.0 V battery and draws 2.6 × 10−3 A of current. What is the power rating of the calculator?

Description : A graphing calculator uses a 6.0 V battery and draws 2.6 × 10−3 A of current. What is the power rating of the calculator?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

Abandoned dogs- is there assistance with intial expenses?

Description : Abandoned dogs- is there assistance with intial expenses?

Last Answer : Have you tried calling your local SPCA to see if they could recommend anything for you? I haven’t ever really heard of anything, but if there is something, they would know it.

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (C) Remains unchanged

Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Description : Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Last Answer : Solution: Given, Z1=10+j5, Z2=8+j9, V=200+j0

Current in a 60 W light bulb when it is connected to a 230 V power supply is A. 0.26 A B. 1.5 A C. 2.6 A D. 3.9 A

Description : Current in a 60 W light bulb when it is connected to a 230 V power supply is A. 0.26 A B. 1.5 A C. 2.6 A D. 3.9 A

Last Answer : 0.26 A

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Description : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Last Answer : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes

With the selector switches set for R X 10,000 and the leads placed in the proper receptacles, the needle settles on the '150' mark. What is the resistance value between the leads? EL-0047 A. 1500 ohms B. 150,000 ohms C. 1,500,000 ohms D. 1.5 ohms

Description : With the selector switches set for R X 10,000 and the leads placed in the proper receptacles, the needle settles on the '150' mark. What is the resistance value between the leads? EL-0047 A. 1500 ohms B. 150,000 ohms C. 1,500,000 ohms D. 1.5 ohms

Last Answer : Answer: C

__________ does not contain copper as an alloying element, (A) Nichrome (B) Manganin (C) Perminvar (D) Monel metal

Description : __________ does not contain copper as an alloying element, (A) Nichrome (B) Manganin (C) Perminvar (D) Monel metal

Last Answer : (A) Nichrome

If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Description : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Last Answer : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s.

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

If an electrical heater has three heating elements connected in parallel why does each element have its own fusible link and limit switch?

Description : If an electrical heater has three heating elements connected in parallel why does each element have its own fusible link and limit switch?

Last Answer : What is the answer ?

Nichrome wire is used in an electric heater because _______. (1) It has high resistance (2) It has high melting point (3) It can resist a current upto approx 5 amperes (4) For all of the above reasons

Description : Nichrome wire is used in an electric heater because _______. (1) It has high resistance (2) It has high melting point (3) It can resist a current upto approx 5 amperes (4) For all of the above reasons

Last Answer : (4) For all of the above reasons

Two bulbs consume same energy when operated at `200 V and 300 V` , respectively . When these bulbs are connected in series across a dc source of `500

Description : Two bulbs consume same energy when operated at `200 V and 300 V` , respectively . When these bulbs are connected in series across a dc source of `500

Last Answer : Two bulbs consume same energy when operated at `200 V and 300 V` , respectively . When these bulbs ... ratio of powers consumed across them is `2//3`

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W....

Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR

Do you assume that when a person settles a case outside of court that they are probably guilty and just don’t want the world to hear the details?

Description : Do you assume that when a person settles a case outside of court that they are probably guilty and just don’t want the world to hear the details?

Last Answer : I assume the person is likely guilty, BUT I understand that might not be the case, especially for famous people. I definitely feel the public doesn’t know all of the details and shouldn’t make a quick judgment.

How can attorneys on tv guarantee they can win your case and get you immediate compensation before your case settles?

Description : How can attorneys on tv guarantee they can win your case and get you immediate compensation before your case settles?

Last Answer : They most likely have an insurance company pick up the bill when they lose, as long as they win often enough an insurance company could afford it. Just a guess though.

Who settles the disputes arising in connection with the election -SST 10th

Description : Who settles the disputes arising in connection with the election -SST 10th

Last Answer : The disputes arising in connection with the election of a President is settled down by the Supreme Court of India.

Which is not a correct statement? The Supreme Court: (1) is a watch-dog of citizen's liberty (2) settles electoral disputes of the President and Vice-President of India (3) interprets the Constitution (4) protects the Directive Principles of State Policy

Description : Which is not a correct statement? The Supreme Court: (1) is a watch-dog of citizen's liberty (2) settles electoral disputes of the President and Vice-President of India (3) interprets the Constitution (4) protects the Directive Principles of State Policy

Last Answer : (4) protects the Directive Principles of State Policy Explanation: The Directive Principles of State Policy are guidelines/ principles given to the central and state governments of India, to be kept in ... , contained in Part IV of the Constitution of India, are not enforceable by any court.

NEFT is an electronic fund transfer system that operates on a _________ basis which settles transactions in batches. A. Domain Net Settlement (DNS) B. Defined Net Settlement (DNS) C. Declared Net Settlement (DNS) D. Deferred Net Settlement (DNS)

Description : NEFT is an electronic fund transfer system that operates on a _________ basis which settles transactions in batches. A. Domain Net Settlement (DNS) B. Defined Net Settlement (DNS) C. Declared Net Settlement (DNS) D. Deferred Net Settlement (DNS)

Last Answer : D. Deferred Net Settlement (DNS) Explanation: NEFT is an electronic fund transfer system that operates on a Deferred Net Settlement (DNS) basis which settles transactions in batches. In DNS, the ... till the particular cut-off time. These transactions are netted (payable and receivables) in NEFT.

A particle A of diameter 10 microns settles in an oil of specific gravity 0.9 and viscosity 10 poise under Stoke's law. A particle B with diameter 20microns settling in the same oil will have a settling velocity (A) Same as that of A (B) One fourth as that of A (C) Twice as that of A (D) Four times as that of A

Description : A particle A of diameter 10 microns settles in an oil of specific gravity 0.9 and viscosity 10 poise under Stoke's law. A particle B with diameter 20microns settling in the same oil will have a settling velocity (A) ... ) One fourth as that of A (C) Twice as that of A (D) Four times as that of A

Last Answer : (B) One fourth as that of A

For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Description : For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust (A) Is increased (B) Is decreased (C) Remains unchanged (D) Becomes zero

Last Answer : (B) Is decreased