Fouling factor (A) Is a dimensionless quantity (B) Does not provide a safety factor for design (C) Accounts for additional resistances to heat flow (D) None of these

Fouling factor

(A) Is a dimensionless quantity

(B) Does not provide a safety factor for design

(C) Accounts for additional resistances to heat flow

(D) None of these

by

1 Answer

Answer :

(C) Accounts for additional resistances to heat flow


by

Related questions

Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Description : Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Last Answer : (B) Factor of safety

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Specific __________ is a dimensionless quantity. (A) Heat (B) Humidity (C) Weight (D) None of these

Description : Specific __________ is a dimensionless quantity. (A) Heat (B) Humidity (C) Weight (D) None of these

Last Answer : (D) None of these

Which of the following is correct regarding isolation factor? a) Dimensionless quantity b) Has Newton as its unit c) Has joule as its Unit d) Has Hz as its unit

Description : Which of the following is correct regarding isolation factor? a) Dimensionless quantity b) Has Newton as its unit c) Has joule as its Unit d) Has Hz as its unit

Last Answer : a) Dimensionless quantity

Pick up the correct statement from the following: (A) Coefficient of compressibility is the decrease in void ratio per unit increase of pressure (B) The percent settlement at any time is called degree of consolidation (C) Time factor is a dimensionless quantity (D) All the above

Description : Pick up the correct statement from the following: (A) Coefficient of compressibility is the decrease in void ratio per unit increase of pressure (B) The percent settlement at any time is called degree of consolidation (C) Time factor is a dimensionless quantity (D) All the above

Last Answer : Answer: Option D

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Description : Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Last Answer : (B) 1/U1 - 1/U2

The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Description : The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Last Answer : (D) Nu, Gz

Dimensions of strain are A. [L] B. [M] [L]-1 [T]-2 C. [L]-1 D. It's a dimensionless quantity

Description : Dimensions of strain are A. [L] B. [M] [L]-1 [T]-2 C. [L]-1 D. It's a dimensionless quantity

Last Answer : It's a dimensionless quantity

Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Last Answer : (d) Both (b) and (c)

In SI units, fouling factor is expressed in (A) m2°K/W (B) W/m2°K (C) m2°K (D) m°K/W

Description : In SI units, fouling factor is expressed in (A) m2°K/W (B) W/m2°K (C) m2°K (D) m°K/W

Last Answer : (A) m2°K/W

Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Description : Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Last Answer : (D) None of these

Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Description : Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Last Answer : (D) Density

Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch

Description : Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch chemical-engineering

Last Answer : (B) Triangular pitch

Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Description : Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Last Answer : C) Both 'a' & 'b'

The friction factor is (A) Always inversely proportional to the Reynolds number (B) Not dimensionless (C) Not dependent on the roughness of the pipe (D) None of these

Description : The friction factor is (A) Always inversely proportional to the Reynolds number (B) Not dimensionless (C) Not dependent on the roughness of the pipe (D) None of these

Last Answer : (D) None of these

Which of the following is dimensionless? (A) Angular velocity (B) Fanning friction factor (C) Specific volume (D) None of these

Description : Which of the following is dimensionless? (A) Angular velocity (B) Fanning friction factor (C) Specific volume (D) None of these

Last Answer : (B) Fanning friction factor

The unit of frequency factor in Arrhenius equation is (A) Same as that of rate constant (B) Same as that of activation energy (C) Dimensionless (D) None of these

Description : The unit of frequency factor in Arrhenius equation is (A) Same as that of rate constant (B) Same as that of activation energy (C) Dimensionless (D) None of these

Last Answer : (A) Same as that of rate constant

Sommerfeld number is (A) Similar to bearing characteristic number (B) Similar to Reynold’s number (C) Dimensionless parameter that contains all the design parameters (D) Used to find out dynamic load carrying capacity of the hydrodynamic bearing

Description : Sommerfeld number is (A) Similar to bearing characteristic number (B) Similar to Reynold’s number (C) Dimensionless parameter that contains all the design parameters (D) Used to find out dynamic load carrying capacity of the hydrodynamic bearing

Last Answer : (C) Dimensionless parameter that contains all the design parameters

Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Description : Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Last Answer : (A) Schmidt

Corresponding to Nusselt number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Sherwood (B) Schmidt (C) Peclet (D) Stanton

Description : Corresponding to Nusselt number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Sherwood (B) Schmidt (C) Peclet (D) Stanton

Last Answer : (A) Sherwood

The dimensionless group in mass transfer that is equivalent to Prandtl number in heat transfer is (A) Nusselt number (B) Sherwood number (C) Schmidt number (D) Stanton numbe

Description : The dimensionless group in mass transfer that is equivalent to Prandtl number in heat transfer is (A) Nusselt number (B) Sherwood number (C) Schmidt number (D) Stanton numbe

Last Answer : (C) Schmidt number

The compressibility factor, x, is used for predicting the behavior of nonideal gases. How is the compressibility ty factor defined relative to an ideal gas? (subscript “c”refers to critical value)  A. z = P / Pc  B. z = pV/ RT  C. z = T /Tc  D. z = RT / pV Hint: for an real gases the compressibility factor, x, is an dimensionless constant given by pV=zRT. Therefore z = pV / RT

Description : The compressibility factor, x, is used for predicting the behavior of nonideal gases. How is the compressibility ty factor defined relative to an ideal gas? (subscript c refers to critical value)  A. ... compressibility factor, x, is an dimensionless constant given by pV=zRT. Therefore z = pV / RT

Last Answer : z = pV/ RT

Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress. (A) Working (B) Bearing (C) Yield (D) None of these

Description : Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress. (A) Working (B) Bearing (C) Yield (D) None of these

Last Answer : Option A

Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Description : Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Last Answer : (D) Non uniform direction of velocities at inlet & outlet sections

What additional factor will be changed if the directions of a current flow is changed?

Description : What additional factor will be changed if the directions of a current flow is changed?

Last Answer : direction of magnetic field

Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the(A) Quantity & temperature of waste gas(B) Dust concentration & nature of dust in waste gas(C) Corrosive nature of the waste gas(D) All (A), (B) and (C)

Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)

Last Answer : (B) Dust concentration & nature of dust in waste gas

Heat flux through several resistances in series in analogous to the current flowing through several (A) Resistances in parallel (B) Capacitors in series (C) Resistances in series (D) None of these

Description : Heat flux through several resistances in series in analogous to the current flowing through several (A) Resistances in parallel (B) Capacitors in series (C) Resistances in series (D) None of these

Last Answer : (C) Resistances in series

Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Description : Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Last Answer : (B) Sum of all resistances

In case of a multipass shell and tube heat exchanger, the temperature drop in the fluid (A) Is inversely proportional to the resistance across which the drop occurs (B) And the wall are proportional to individual resistances (C) And the wall is not related (D) None of these

Description : In case of a multipass shell and tube heat exchanger, the temperature drop in the fluid (A) Is inversely proportional to the resistance across which the drop occurs (B) And the wall are proportional to individual resistances (C) And the wall is not related (D) None of these

Last Answer : (B) And the wall are proportional to individual resistances

The overall resistance for heat transfer through a series of flat resistance, is the __________ of the resistances. (A) Average (B) Geometric mean (C) Product (D) Sum

Description : The overall resistance for heat transfer through a series of flat resistance, is the __________ of the resistances. (A) Average (B) Geometric mean (C) Product (D) Sum

Last Answer : (D) Sum

In a shell and tube heat exchanger, (A) The temperature drops in the two fluids and the wall are proportional to individual resistances (B) The temperature drop is inversely proportional to the resistance across which the drop occurs (C) There is no relationship between temperature drop and resistance (D) The relationship is not generalised

Description : In a shell and tube heat exchanger, (A) The temperature drops in the two fluids and the wall are proportional to individual resistances (B) The temperature drop is inversely proportional to ... ) There is no relationship between temperature drop and resistance (D) The relationship is not generalised

Last Answer : (A) The temperature drops in the two fluids and the wall are proportional to individual resistances

Factor of safety in the design of springs is usually (A) 1.5 or less (B) 3 or less (C) 4.5 or less (D) 6 or less

Description : Factor of safety in the design of springs is usually (A) 1.5 or less (B) 3 or less (C) 4.5 or less (D) 6 or less

Last Answer : (A) 1.5 or less

If Q is load factor, S is shape factor and F is factor of safety in elastic design, the following: (A) Q = S + F (B) Q = S - F (C) Q = F - S (D) Q = S × F

Description : If Q is load factor, S is shape factor and F is factor of safety in elastic design, the following:  (A) Q = S + F (B) Q = S - F (C) Q = F - S (D) Q = S × F

Last Answer : (D) Q = S × F

For the design of retaining walls, the minimum factor of safety against overturning is taken as (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Description : For the design of retaining walls, the minimum factor of safety against overturning is taken as (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0

Last Answer : Answer: Option B

Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ A ] 1.15

Partial safety factor for strength of concrete in Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength of concrete in Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ C ] 1.5

Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ A ] 1.15

Partial safety factor for strength of concrete in Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Description : Partial safety factor for strength of concrete in Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65

Last Answer : [ C ] 1.5

In Limit state method of design, the factor of safety for concrete and steel respectively are [ A ] 3.00 and 1.80 [ B ] 1.50 and 1.18 [ C ] 1.50 and 1.15 [ D ] 1.50 and 1.50

Description : In Limit state method of design, the factor of safety for concrete and steel respectively are [ A ] 3.00 and 1.80 [ B ] 1.50 and 1.18 [ C ] 1.50 and 1.15 [ D ] 1.50 and 1.50

Last Answer : [ C ] 1.50 and 1.15

In working stress method of design, the factor of safety for concrete and steel respectively are [ A ] 3.0 and 1.8 [ B ] 3.0 and 1.18 [ C ] 3.0 and 1.15 [ D ] 1.5 and 1.5

Description : In working stress method of design, the factor of safety for concrete and steel respectively are [ A ] 3.0 and 1.8 [ B ] 3.0 and 1.18 [ C ] 3.0 and 1.15 [ D ] 1.5 and 1.5

Last Answer : [ A ] 3.0 and 1.8

Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Description : Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Last Answer : (C) Spark plug fouling

For initial audits, additional matters the auditor may consider in the overall audit strategy and audit plan include the following except a. Major issues including the application of accounting principles or any auditing and reporting standards discussed with management. b. Confirmation of material accounts receivable balance at the end of the year. c. Planned audit procedure to obtain sufficient appropriate audit evidence regarding opening balances. d. Assignment of firm personnel with appropriate levels of capabilities and competence to respond to anticipated significant risks

Description : For initial audits, additional matters the auditor may consider in the overall audit strategy and audit plan include the following except a. Major issues including the application of ... firm personnel with appropriate levels of capabilities and competence to respond to anticipated significant risks

Last Answer : Confirmation of material accounts receivable balance at the end of the year.

How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps

Description : How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps

Last Answer : Answer: A

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Idea discussion - How useful are super freezers as an additional powerless safety precaution?

Description : Idea discussion - How useful are super freezers as an additional powerless safety precaution?

Last Answer : I think it’a a great idea @mattbrowne! It would be costly, but doable in terms of the cost of reactors now.

The work index in Bond's law for crushing of solids has the following dimensions (A) No units (dimensionless) (B) kWh/ton (C) kW/ton (D) kWh.m1/2 /ton

Description : The work index in Bond's law for crushing of solids has the following dimensions (A) No units (dimensionless) (B) kWh/ton (C) kW/ton (D) kWh.m1/2 /ton

Last Answer : (B) kWh/ton

Buckingham-π theorem states that in any physical problem includingn' quantities having 'm' dimensions, the quantities can be arranged into __________ independent dimensionless parameters. (A) m (B) n (C) n-m (D) n/m

Description : Buckingham-π theorem states that in any physical problem includingn' quantities having 'm' dimensions, the quantities can be arranged into __________ independent dimensionless parameters. (A) m (B) n (C) n-m (D) n/m

Last Answer : (C) n-m

Which of the following is a dimensionless parameter? (A) Angular velocity (B) Specific weight (C) Kinematic viscosity (D) None of these

Description : Which of the following is a dimensionless parameter? (A) Angular velocity (B) Specific weight (C) Kinematic viscosity (D) None of these

Last Answer : (D) None of these