Explain the calibration of single phase electronic energy meter using direct loading.

Explain the calibration of single phase electronic energy meter using direct loading.
by

1 Answer

Answer :

Calibration of Single-phase Electronic Energy Meter by Direct Loading Method: The following figure shows the arrangement of calibration for single phase electronic energy meter. A phase shifter is connected for changing power factor of circuit. The energy readings are taken for different values of current at different power factors. 

electronics2electrical.com 754 - .jpg

electronics2electrical.com 755 - .jpg

by

Related questions

With neat diagram explain calibration of energy meter by direct loading method.

Description : With neat diagram explain calibration of energy meter by direct loading method.

Last Answer : Calibration of Energy Meter by Direct Loading Method:  There are three methods for testing/calibration:  1. Long period dial test  2. Using rotary sub- standard meter  3. Using precision grade instruments  All ... of substandard meter in kWh  Then % error = [(D - DS)/DS] x 100

Describe with block diagram; the construction of single phase electronic energy meter.

Description : Describe with block diagram; the construction of single phase electronic energy meter. 

Last Answer : Construction of Single Phase Electronic Energy Meter: 1. CT reduces current to reasonable value for current scaling network. 2. Voltage & current scaling networks reduce proportionally the ... The ADC converts the square wave frequency analog output to display the energy in Watt-hour.

List the errors occuring in single phase electronic energy meter.

Description : List the errors occuring in single phase electronic energy meter.

Last Answer : Errors in Single Phase Electronic Energy Meter: 1) Error due to wrong sensor opeartion. 2) Error due to temperature. 3) Error due to wrong CT opeartion. 4) Error due to wrong PT opeartion. 5 ... of scaling network. 6) Error due to wrong ADC opeartion. 7) Error due to wrong Display. 

Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Description :  Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Last Answer : Labeled diagram of 3-phase electronic energy meter:

State the purpose of calibration of measuring instruments. Explain the procedure of calibration of D.C. voltmeter by using D.C. potentiometer.

Description : State the purpose of calibration of measuring instruments. Explain the procedure of calibration of D.C. voltmeter by using D.C. potentiometer.

Last Answer : Purpose of calibration : Calibration is the process of evaluating and adjusting the precision and accuracy of measuring equipment. Proper calibration of an instrument allows people to have a safe ... calibration curve can be drawn by plotting the percentage error against the measured voltages. 

State the advantages of electronic energy meter.

Description : State the advantages of electronic energy meter. 

Last Answer : Advantages of Electronic Energy Meter: 1) Low cost. 2) High accuracy. 3) More flexibility. 4) High sensitivity 5) No frictional losses. 6) Less loading effect. 7) High frequency ... for external adjustment. 11) Low load, full load, power factor and creeping adjustments are not required.

Explain direct loading test on single phase transformer with neat circuit diagram.

Description : Explain direct loading test on single phase transformer with neat circuit diagram. 

Last Answer : Direct loading test on single phase transformer with neat circuit diagram:   Direct loading test on transformer is carried out to calculate the losses, efficiency and voltage regulation of the ... voltage.  Efficiency and regulation can be calculated by using following formulae:   

State the meaning of energy meter constant K. State its unit.

Description : State the meaning of energy meter constant K. State its unit.

Last Answer : Meaning of Energy Meter Constant (K): Energy Meter Constant is the no. of revolutions made by disc in meter per unit (kWh) consumption of energy. Unit of energy meter constant K is rev/kWH

A single phase wattmeter rated for 500 V; 5A is having full scale deflection of 1000 watt. What is multiplying factor of the wattmeter?

Description : A single phase wattmeter rated for 500 V; 5A is having full scale deflection of 1000 watt. What is multiplying factor of the wattmeter?

Last Answer : Answer :

Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Description : Draw the circuit diagram for:- i) Measurement of active power in 3-phase load circuit using two wattmeter. ii) Measurement of reactive power in 3-phase load circuit using one wattmeter.

Last Answer : (i) Measurement of active power in 3- phase load circuit using two- wattmeter: (ii) Measurement of reactive power in 3- phase load circuit using one wattmeter

Draw the block diagram of tri-vector meter. State the various measurements possible from tri-vector meter.

Description : Draw the block diagram of tri-vector meter. State the various measurements possible from tri-vector meter.

Last Answer : Various measurements possible from tri-vector meter are: Tri-vector meter is a measuring instrument which measures the kWh, kVArh, the kVAh of a power line. Tri-vector meter is an energy meter ... of supply such as voltage, current, power factor, active load, reactive load, apparent load etc.

Describe with block diagram the working of digital frequency meter.

Description : Describe with block diagram the working of digital frequency meter.

Last Answer : Digital frequency meter: Amplifier: The signal whose frequency is to be measured is first amplified and supplied to the schmitt trigger. Schmitt Trigger: The schmitt trigger convert ... count displayed on counter  t = time interval between start and stop condition of the gate 

State the purpose of four quadrant meter.

Description : State the purpose of four quadrant meter.

Last Answer : Purpose of four quadrant meter:  Four-quadrant meter is basically a bidirectional energy-meter with additional measurement facility. The purposes of four-quadrant meter are: 1) Measurement of energy/power ... and kVARh 3) Time-of-use metering: Bidirectional consumption and demand.

Errors due to frictions of the meter movement, incorrect spring tension, improper calibration or faulty instruments:

Description : Errors due to frictions of the meter movement, incorrect spring tension, improper calibration or faulty instruments:

Last Answer : instrument errors

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

Phantom loading for testing of energy meter is used

Description : Phantom loading for testing of energy meter is used (A) to isolate the current and potential circuits (B) to increase power loss during testing (C) for meters having low current ratings (D) to test meters having a large current rating for which loads may not be available

Last Answer : B

In a single phase induction energy meter, in order to obtain true value of energy, the shunt

Description : In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by   (a) 90o (b) 0o (c) 45o (d) 60o

Last Answer : In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by 90o

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is

Description : The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

Last Answer : The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is 500 W

The current coil of a single-phase energy meter is wound on

Description : The current coil of a single-phase energy meter is wound on (a) One limb of the laminated core (b) Both the limbs of the laminated core with same number of turns (c) Both the limbs of the laminated core with different number of turns (d) The centre of the limb on the laminated core

Last Answer : The current coil of a single-phase energy meter is wound on Both the limbs of the laminated core with same number of turns

One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter...

Description : One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant is 400 rev/kWh. The power factor of the load is

Last Answer : One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant is 400 rev/kWh. The power factor of the load is 0.8

A single phase energy meter has a constant of 1200 revolution/kWh. When a load of 200 W is connected,...

Description : A single phase energy meter has a constant of 1200 revolution/kWh. When a load of 200 W is connected, the disc rotates at 4.2 revolutions per min. If the load is on for 10 hours, the meter records an excess of   (a) 0.1 kWh (b) 0.2 kWh (c) 1.0 kWh (d) 2.0 kWh 

Last Answer : 2

The series magnet of a single phase Energy meter consists of coil of _____.

Last Answer : The series magnet of a single phase Energy meter consists of coil of thick wire of few turns.

Describe the procedure for the measurement of earth resistance by using earth tester.

Description : Describe the procedure for the measurement of earth resistance by using earth tester.

Last Answer : Measurement of earth resistance by using earth tester:  It is connected to earth electrode E, whose resistance is to be measured, and the other spike P and R, as shown in the ... , the deflection of the pointer will indicate directly resistance in ohm of the earth electrode under test. 

Define electrical energy. State its unit.

Description : Define electrical energy. State its unit.

Last Answer : Electrical Energy: Electrical energy is defined as the work done in moving electrical charge in electrical field. OR The total power delivered or consumed by electrical load over specific unit time ... unit of electrical energy is the joule (or watt-second) OR Kilowatt-hour ( kWH ).

Electronic Stability Program is use to a) Assist in braking b) Reducing loss of traction c) Use in ECU d) for proper loading and unloading of weight in vehicle

Description : Electronic Stability Program is use to a) Assist in braking b) Reducing loss of traction c) Use in ECU d) for proper loading and unloading of weight in vehicle

Last Answer : b) Reducing loss of traction

Explain with neat sketch the construction and working principle of megger.

Description : Explain with neat sketch the construction and working principle of megger.

Last Answer : Megger: Construction of Megger : Two coils: the current coil and pressure coil are mounted at an angle on the same spindle and form the part of the moving system. These coils are ... force produces a torque that is used to deflect the pointer of the device which gives some reading.

Explain the effect of power factor on wattmeter reading in two wattmeter method for power measurement.

Description : Explain the effect of power factor on wattmeter reading in two wattmeter method for power measurement.

Last Answer : Effect of P.F. on Reading of Wattmeter in Two Wattmeter Method:

Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Description : Explain with neat sketch; the construction and working principle of Repulsion type moving iron instrument.

Last Answer : Repulsion Type Moving Iron Instrument: Construction: It consist of fixed cylinder hollow coil which carries operating current inside the coil there are two soft iron pieces. One of which is ... magnetized with same polarity a repulsive force act on them and moving iron piece gets deflected. 

Explain the error occurred due to pressure coil inductance of electrodynamometer type wattmeter. How this error is compensated?

Description : Explain the error occurred due to pressure coil inductance of electrodynamometer type wattmeter. How this error is compensated?

Last Answer : For power measurement assume that the pressure coil of wattmeter is purely restitive. Hence current taken by pressure coil Ipc is in phase with voltage across the pressure coil Vpc  ... inductive reactance XL the pressure coil circuit is made purely resistive and the error is eliminated.

Explain with neat sketch, the working of full wave rectifier voltmeter.

Description : Explain with neat sketch, the working of full wave rectifier voltmeter.

Last Answer : Full Wave Rectifier Type Voltmeter: Working of full wave rectifier type A. C. Voltmeter Referring to the circuit diagram, for rectification, a full wave bridge circuit (ABCD) is used. Input ... current passing through meter is given as, which causes full scale deflection of the meter.

Draw a block diagram of electronic energy meter. Write function of each block.

Description : Draw a block diagram of electronic energy meter. Write function of each block.

Last Answer : Electronic Energymeter  Functions of components/blocks: - CT reduces current to reasonable value for current scaling network. - Voltage & current scaling networks reduce proportionally the voltage ... ADC converts the square wave frequency analog output to display the energy in watthour.

Draw and describe working of electronic energy meter.

Description : Draw and describe working of electronic energy meter.

Last Answer : working of electronic energy meter:- 1. CT reduces current to reasonable value for current scaling network. 2. Voltage & current scaling networks reduce proportionally the voltage & ... The ADC converts the square wave frequency analog output to display the energy in watthour. 

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016

Description : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last Answer : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

The meter constant of a single-phase 230 V induction watt hour meter is 400 revolutions per kWh....

Description : The meter constant of a single-phase 230 V induction watt hour meter is 400 revolutions per kWh. The speed of the meter disc for a current of 10 A of 0.9 pf lagging will be

Last Answer : The meter constant of a single-phase 230 V induction watt hour meter is 400 revolutions per kWh. The speed of the meter disc for a current of 10 A of 0.9 pf lagging will be 13.80 rpm

In a household single phase induction type wattmeter, the meter can be reversed by: -

Description :  In a household single phase induction type wattmeter, the meter can be reversed by: - a) reversing the supply terminals b) reversing the load terminal c) opening the meter connection ... opening the meter and reversing the connection of both the potential coil terminals and current coil terminals

Last Answer :  In a household single phase induction type wattmeter, the meter can be reversed by: - opening the meter connection and reversing either the potential coil terminals or current coil terminals 

In a single phase power factor meter the phase difference between the currents in the two pressure coils is?

Last Answer : In a single phase power factor meter the phase difference between the currents in the two pressure coils is exactly 90°.

The two pressure coils of a single phase power factor meter have?

Last Answer : The two pressure coils of a single phase power factor meter have the same dimensions and the same number of turns.

Direct measurement of permeability of the specimen at any stage of loading can be made (A) Only in fixed ring type consolidometer (B) Only in floating ring type consolidometer (C) Both (A) and (B) (D) None of the above

Description : Direct measurement of permeability of the specimen at any stage of loading can be made (A) Only in fixed ring type consolidometer (B) Only in floating ring type consolidometer (C) Both (A) and (B) (D) None of the above

Last Answer : Answer: Option A

What is the difference between Direct Path and Conventional Path loading?

Description : What is the difference between Direct Path and Conventional Path loading?

Last Answer : A conventional path load executes SQL INSERT statements to populate tables in an Oracle database. A direct path load eliminates much of the Oracle database overhead by formatting Oracle data blocks and writing the data blocks directly to the database files.

Define calibration of instruments. Explain why calibration is needed for measuring instruments.

Description : Define calibration of instruments. Explain why calibration is needed for measuring instruments.

Last Answer : Calibration - It is a process of estimating the value of a quantity by comparing that quantity with a standard quantity. Need of calibration: - Calibration defines the accuracy and quality ... aim of calibration is to minimize any measurement uncertainty by ensuring the accuracy of test equipment.

Explain the process of calibration of pressure gauge by Dead Weight Tester.

Description : Explain the process of calibration of pressure gauge by Dead Weight Tester.

Last Answer : Deadweight Testers (DWT) are the primary standard for pressure measurement. A dead weight tester is an instrument that calibrates pressure by determining the weight of force divided by the area the force ... at each gauge reading and ensure that it is within the acceptable accuracy limits.

Explain calibration of capacitive type level measurement.

Description : Explain calibration of capacitive type level measurement.

Last Answer : ➢ Calibration of capacitance type level transmitter 1. Remove the level transmitter from the system(tank). 2. check whether transmitter shows zero reading by connecting with multimeter otherwise release the ... rotate the span screw to 20ma. 3. Repeat these steps and check all readings

Explain the calibration of series type ohmmeter.

Description : Explain the calibration of series type ohmmeter.

Last Answer : Series Ohmmeter If the resistor's value is unknown and has to be measured by placing it in series with the ohmmeter, then that ohmmeter is called series ohmmeter. The circuit diagram of ... hand of the scale respectively. Series ohmmeter is useful for measuring high values of resistances.

need of calibration and explain the procedure to calibrate the instrument.

Description : need of calibration and explain the procedure to calibrate the instrument.

Last Answer : Need of calibration: Every measuring device degrades over time due to normal wear and tear. These changes can be caused by various reasons such as electric or mechanical shock or a hazardous manufacturing ... different magnitude are used to calculate the resistance based on ohm's law.

Explain need of calibration of any instrument.

Description : Explain need of calibration of any instrument.

Last Answer : Calibration is the comparison between measurements: between a standard known value and the unknown value.  There are three main reasons for having instruments calibrated: 1. To ensure readings from an instrument ... . 3. To establish the reliability of the instrument i.e. that it can be trusted.

Define calibration. Explain process of calibration in detail.

Description : Define calibration. Explain process of calibration in detail. 

Last Answer : The process of deriving the value of a quantity by comparing that quantity with a standard quantity is called as calibration. Calibration of instrument is done to obtain correct unknown value of each ... instrument reading. To establish the reliability of the instrument i.e. it can be trusted. 

Explain principles of calibration.

Description : Explain principles of calibration.

Last Answer : The process of deriving the value of a quantity by comparing that quantity with a standard quantity is called as calibration. Calibration of instrument is done to obtain correct unknown value of each scale reading on measuring instrument

In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction motor C. is the armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Last Answer : Answer: B

Which type of AC single-phase motor will also operate on direct current? A. Split-phase B. Series-wound C. Shaded-pole D. Repulsion-start

Description : Which type of AC single-phase motor will also operate on direct current? A. Split-phase B. Series-wound C. Shaded-pole D. Repulsion-start

Last Answer : Answer: B

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2