Description : The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness
Last Answer : (B) Resilience
Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience
Last Answer : (B) Toughness
Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed
Last Answer : a) Elastically
Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Last Answer : (A) Resilience
Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Description : Percentage elongation of a material is a measure of its (A) Ductility (B) Brittleness (C) Toughness (D) Malleability
Last Answer : (A) Ductility
Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience
Last Answer : (C) Hardness
Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness
Last Answer : a) Modulus of elasticity
Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned
Last Answer : a) Ability of material to absorb energy when deformed elastically
Description : Most important property of steels for use in automobile bodies is the (A) Formability (B) Yield strength (C) Toughness (D) Resilience
Last Answer : (A) Formability
Description : A major difference between light cured and chemical cured composite is that during setting or in function the light cured material tends to:******** VERY IMP A. Seal the margins better and ... on time C. Undergo greater colour change D. Shrink more rapidly E. Posses greater fracture toughness
Last Answer : D. Shrink more rapidly
Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue
Last Answer : d) Fatigue
Description : Brittleness is opposite to (a) Toughness (b) Plasticity (c) Malleability (d) None of these
Last Answer : b) Plasticity
Description : The most serious manufacturing defect from fracture toughness point of view is (A) Surface roughness (B) Pores (C) Spherical inclusion (D) Crack
Last Answer : Option D
Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength
Last Answer : Option A
Description : A hollow sphere and a solid sphere of the same material and equal radii are heated to the same temperature. In this case, (A) The cooling rate will be the same for the two spheres and hence the ... equal amount of radiation from the surrounding in the beginning (D) Both (B) & (C)
Last Answer : (D) Both (B) & (C)
Description : A material is able to retain the deformation permanently by virtue of its (A) Elasticity (B) Plasticity (C) Ductility (D) Malleability
Last Answer : (B) Plasticity
Description : Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these
Last Answer : (A) Creep
Description : The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability? (A) Lead (B) Copper (C) Aluminium (D) Wrought iron
Last Answer : (A) Lead
Description : A material subjected __________ must have high resilience. (A) Shock loading (B) Vibration (C) Fatigue (D) Tension
Last Answer : (A) Shock loading
Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit
Last Answer : D) Endurance limit
Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material
Last Answer : c. Energy required to cause failure
Description : Grindability of a material does not depend upon its (A) Elasticity (B) Hardness (C) Toughness (D) Size
Last Answer : (D) Size
Description : Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its ... (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature
Last Answer : (C) Cold working of a metal decreases its fatigue strength
Description : Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness
Last Answer : A) Machinability
Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength
Last Answer : (A) Modulus of elasticity (young's modulus)
Description : _______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive
Last Answer : (A) Hardness
Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue
Last Answer : (B) Toughnes
Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness
Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share
Description : Springs are used, (A) To absorb shocks and vibrations (B) To store and release energy (C) To measure force (D) For any of the above functions
Last Answer : (D) For any of the above functions
Description : Which of the following function can the spring perform? a) Store energy b) Absorb shock c) Measure force d) All of the mentioned
Last Answer : d) All of the mentioned
Description : The springs in brakes and clutches are used (a) To apply forces (b) To measure forces (c) To absorb shocks (d) To absorb strain energy
Last Answer : (a) To apply forces
Description : In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces
Last Answer : (d) To measure forces
Description : The ability of a material to be formed by hammering or rolling is known as _________ a) Malleability b) Ductility c) Harness d) Brittleness
Last Answer : a) Malleability
Description : The property of a material by which it can be beaten or rolled into thin plates, is called (A) Malleability (B) Ductility (C) Plasticity (D) Elasticity
Last Answer : (A) Malleability
Description : The property of a material by which it can be drawn to a smaller section, due to tension, is called (A) Plasticity (B) Ductility (C) Elasticity (D) Malleability
Last Answer : (B) Ductility
Description : The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability
Last Answer : (b) Ductility
Description : The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleabilityy
Last Answer : (c) Ductility
Description : The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability
Last Answer : (d) Malleability
Description : Property of material which allows it to be drawn out into wires is (A) Ductility. (B) Solder ability. (C) Super conductivity. (D) Malleability.
Last Answer : (A) Ductility.
Description : Write on ductility and malleability of material.
Last Answer : Ductility Ductility is the ability of a material to deform plastically without fracture under tensile load. Because of this property , materials can be drawn out into fine wire without fracture ... Gold and silver are highly malleable. Malleable metals usually bend and twist in various shapes.
Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these
Last Answer : B
Description : Detrimental property of a material for shock load applications (a) High density (b) Low toughness (c) High strength (d) Low hardness
Last Answer : (b) Low toughness
Description : Pick out the wrong statement. (A) Bronze is an alloy of copper & tin (B) Brass is an alloy of copper & zinc (C) The alloy named 'German silver' does not contain any silver (D) The ability of a material to fracture without appreciable deformation is called its ductility
Last Answer : (D) The ability of a material to fracture without appreciable deformation is called its ductility
Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality
Description : Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does ... (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface
Last Answer : Option B
Description : Pick out the wrong statement. (A) Loamy soil is the best soil for vigorous plant growth, while the clayey soil is solid and hence the plant roots penetrate with difficulty (B) Large ... vegetables (D) Cereal crops grown on alkaline soil absorb higher amount of fluorides thereby spreading fluorosis
Last Answer : (C) Application of large excess of Potassic fertiliser in soil increases the valuable carotene in fruits and vegetables